Generated by kicad-footprint-generator · KiCad file format 20260206
1ED3860MC12MXUMA1
Infineon Technologies · Gate Drive ICs · SOP-16
1ED3860MC12MXUMA1 from Infineon Technologies, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND1 | power_in | Reference ground of the input side; connect directly to the input signal ground. |
| 2 | VCC1 | power_in | Positive input-side supply, to be connected to 5 V or 3.3 V, with a decoupling capacitor placed close to this pin and GND1. |
| 3 | SCL | input | Clock input of the I2C bus, CMOS-compatible at 5 V or 3.3 V and referenced to GND1, with a pull-up resistor to VCC1. |
| 4 | SDA | bidirectional | Serial data I/O of the I2C bus (open-drain, CMOS) for 5 V or 3.3 V microcontroller I/O, referenced to GND1, with a pull-up resistor to VCC1. |
| 5 | RDYC | bidirectional | Open-drain combined ready output (high active), fault-clear input and soft-off input (low active), referenced to GND1 with an external pull-up to VCC1 (typically 2.2 kΩ). |
| 6 | FLT_N | bidirectional | Open-drain fault output (active low) and fault-off input (low active), referenced to GND1 with an external pull-up to VCC1 (typically 2.2 kΩ). |
| 7 | IN | input | Non-inverting gate driver input (5 V or 3.3 V CMOS) with an internal 40 kΩ pull-down that keeps the IGBT off if the pin is not connected. |
| 8 | GND1 | power_in | Reference ground of the input side; connect directly to the input signal ground. |
| 9 | VEE2 | power_in | Negative output-side supply, to be connected to 0 V to -25 V referenced to GND2; if no negative supply is used, all VEE2 pins must be connected to GND2. |
| 10 | CLAMP | power_out | Active Miller clamp output (high-current, connected directly to the IGBT gate), or clamp pre-driver output for an external n-channel MOSFET, or 8-bit ADC sense input between CLAMP and VEE2, depending on register configuration. |
| 11 | OFF | power_out | High-current driver sink output to discharge the IGBT gate through the turn-off gate resistor; it also sinks the soft-off current and serves as sense input for PINSTAT.OFF_PIN and TLTO_LVL. |
| 12 | ON | power_out | High-current driver source output to charge the IGBT gate through the turn-on gate resistor; it is also the sense input for the CLAMP function and PINSTAT.ON_PIN. |
| 13 | DESAT | input | Enhanced desaturation detection input referenced to GND2, connected to the IGBT collector through a protection resistor and high-voltage diode to monitor VCE. |
| 14 | VCC2 | power_in | Positive output-side supply, referenced to GND2, with decoupling capacitors placed close to VCC2-VEE2 and VCC2-GND2. |
| 15 | GND2 | power_in | Reference ground of the output side, connected to the common voltage of a bipolar supply and the IGBT emitter, with decoupling capacitors close to VCC2-GND2 and GND2-VEE2. |
| 16 | VEE2 | power_in | Negative output-side supply, to be connected to 0 V to -25 V referenced to GND2; if no negative supply is used, all VEE2 pins must be connected to GND2. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | SOP-16 |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input to output offset voltage | VOFFSET | 2300 | V | VVEE2,max-VVEE2,min with VVEE2,max ≥ VGND1 ≥ VVEE2,min | 25 | ||
| Supply voltage input side | VVCC1 | -0.3 | 6.5 | V | 25 | ||
| Logic input voltage (IN) | VLogicIN | -0.3 | 6.5 | V | 25 | ||
| Logic input voltage (RDYC, FLT_N) | VLogicRF | -0.3 | 6.5 | V | 25 | ||
| I2C logic input voltage (SDA, SCL) | VLogicI2C | -0.3 | 6.5 | V | 25 | ||
| Open drain logic output current (RDYC, FLT_N) | ILogicOC | 10 | mA | 25 | |||
| I2C logic output current (SDA) | ISDA | 50 | mA | 25 | |||
| Positive supply voltage output side | VVCC2 | -0.3 | 40 | V | 25 | ||
| Negative supply voltage output side | VVEE2 | -40 | 0.3 | V | 25 | ||
| Maximum supply voltage difference output side (VVCC2 - VVEE2) | Vmax2 | 40 | V | 25 | |||
| DESAT input voltage (max printed as VVCC2 + 0.3 V; max value is the offset from VCC2) | VDESAT | -0.3 | 0.3 | V | 25 | ||
| CLAMP input voltage (min printed as VVEE2 - 0.3 V; max as VVCC2 + 0.3 V; values are offsets from VEE2 and VCC2) | VCLAMP | -0.3 | 0.3 | V | 25 | ||
| Maximum CLAMP output current | ICLAMP | 2.4 | A | t < 5 µs | 25 | ||
| Gate driver output voltage (ON, OFF) (min printed as VVEE2 - 0.3 V; max as Vmax2 + 0.3 V; values are offsets) | VOUT | -0.3 | 0.3 | V | 25 | ||
| Maximum CLAMP to VCC2 diode IGBT short circuit clamping time | tCLP | 6 | µs | ICLAMP/OUT = 0.75 A | 25 | ||
| Junction temperature | TJ | -40 | 150 | °C | 25 | ||
| Storage temperature | TStg | -55 | 150 | °C | 25 | ||
| Power dissipation, input side | PD,IN | 100 | mW | @TA = 25 °C | 25 | ||
| Power dissipation, output side | PD,OUT | 700 | mW | @TA = 25°C | 25 | ||
| ESD capability: Human body model | VESDHBM | 2 | kV | 25 | |||
| ESD capability: Charged device model | VESDCDM | 500 | V | 25 | |||
| Supply voltage input side | VVCC1 | 3 | 5.5 | V | 26 | ||
| Logic input voltages (IN, RDYC, FLT_N, SDA, SCL) | VLogicIN | -0.3 | 5.5 | V | 26 | ||
| Positive supply voltage output side | VVCC2 | 13 | 25 | V | 26 | ||
| Negative supply voltage output side | VVEE2 | -25 | 0 | V | 27 | ||
| Supply voltage difference output side (VVCC2 - VVEE2) | Vmax2 | 13 | 35 | V | 27 | ||
| Ambient temperature | TA | -40 | 125 | °C | Note 2: TJ has to be below over temperature protection temperature TOTPOFF | 27 | |
| Switching frequency | fSW | 0 | 250 | kHz | max PD applies | 27 | |
| Common mode transient immunity | /CMTI/ | 0 | 200 | V/ns | VOFFSET,test = 1500 V | 27 | |
| VCC1 UVLO threshold (rising) | VUVLO1H | 2.95 | 3.05 | V | 28 | ||
| VCC1 UVLO threshold (falling) | VUVLO1L | 2.6 | 2.8 | V | 28 | ||
| VCC1 UVLO hysteresis | VHYS1 | 0.1 | 0.14 | V | 28 | ||
| VCC1 quiescent current | IQ1 | 2.4 | 4 | mA | VVCC1 = 3.3 V, IN = High, RDYC = High, FLT_N = High | 28 | |
| VCC1 operating current | IO1 | 2.4 | 4 | mA | VVCC1 = 3.3 V, IN = 16 kHz, 50%, RDYC = High, FLT_N = High, SCL = Low | 28 | |
| VCC2 UVLO threshold (rising), setting 0H | VUVLO2H,0 | 12 | 12.6 | V | UVTLVL.UVVCC2TL = 0H | 28 | |
| VCC2 UVLO threshold (falling), setting 0H | VUVLO2L,0 | 10.4 | 11 | V | 28 | ||
| VCC2 UVLO hysteresis, setting 0H | VHYS2,0 | 0.75 | 1 | V | 28 | ||
| VCC2 UVLO threshold (rising), setting 1H | VUVLO2H,1 | 9.4 | 10 | V | UVTLVL.UVVCC2TL = 1H | 28 | |
| VCC2 UVLO threshold (falling), setting 1H | VUVLO2L,1 | 8 | 8.7 | V | 28 | ||
| VCC2 UVLO hysteresis, setting 1H | VHYS2,1 | 0.6 | 0.7 | V | 28 | ||
| VCC2 quiescent current | IQ2 | 3.9 | 5 | mA | VVCC2 = 15 V, VVEE2 = -8 V, OUT = High, DESAT = Low, DRVCFG.STD_OFF = 0H, DRVFOFF = 00H/01H | 29 | |
| VCC2 operating current | IO2 | 3.9 | 5 | mA | VVCC2 = 15 V, VVEE2 = -8 V, OUT = 16 kHz, 50%, DESAT = Low, CLOAD = 100 pF, DRVCFG.STD_OFF = 0H, DRVFOFF = 00H/01H | 29 | |
| High level clamp voltage (printed as VVCC2 + offset) | VCLAMPH0 | 1.5 | 1.63 | V | ICLAMP = 500 mA | 32 | |
| Clamp threshold voltage (related to VEE2) | VON_CLAMP | 1.5 | 2 | 2.5 | V | 32 | |
| Clamp-driver high level output peak current | ICLAMPH | 0.2 | 0.27 | A | VCC2 = 15 V; VEE2 = 0 V; CCLAMP = 100 nF; RCLAMP = 1 Ω | 32 | |
| Clamp/Clamp-driver output low level current | ICLAMPL,2 | 1.1 | 1.8 | A | VCC2 = 15 V; VEE2 = 0 V; VCLAMP = 2 V; CCLAMP = 100 nF; RCLAMP = 0.1 Ω | 32 | |
| Clamp/Clamp-driver output low level current | ICLAMPL,5 | 2.2 | 3.5 | A | VCC2 = 15 V; VEE2 = 0 V; VCLAMP = 5 V; CCLAMP = 100 nF; RCLAMP = 0.1 Ω | 32 | |
| Clamp/Clamp-driver output low level ON resistance | RDSON,CLP | 0.5 | 0.85 | 1.35 | Ω | ICLAMPL = 200 mA | 32 |
| Input IN to output propagation delay ON | tPDON | 226 | 244 | 270 | ns | CLOAD = 100 pF, VIN = 70%, VOUT=20%, with tINMIN,0 | 34 |
| Input IN to output propagation delay OFF | tPDOFF | 218 | 236 | 262 | ns | CLOAD = 100 pF, VIN = 30%, VOUT=80%, with tINMIN,0 | 34 |
| Input to output propagation delay distortion (tPDOFF - tPDON) | tPDISTO | -23 | -8 | 7 | ns | CLOAD = 100 pF | 34 |
| Input IN to output propagation delay distortion between any devices (tPDON-tPDON) or (tPDOFF-tPDOFF) | tPDD | 30 | ns | same conditions (VIN, VVCC1, VVCC2 and VVEE2, CLOAD, TA, tINMIN,0) | 34 | ||
| Input RDYC or FLT_N to TLTOff output propagation delay (1ED3860M) | tPDRDYCT, tPDFLT_NT | 360 | 417 | 482 | ns | 34 | |
| Rise time 1ED3860M | tRISE | 15 | 30 | ns | CLOAD = 2.2 nF, VOUT: 20% to 80% | 35 | |
| Fall time 1ED3860M | tFALL | 15 | 30 | ns | CLOAD = 2.2 nF, VOUT: 80% to 20% | 35 | |
| DESAT charge current | IDESATC | 470 | 500 | 525 | µA | VDESAT = 0 V | 35 |
| DESAT voltage divider resistance | RDVD | 259 | 312.5 | 366 | kΩ | between DESAT and GND2 pins | 35 |
| DESAT clamp and discharge ON resistance | RDSON,D | 7.7 | 25 | Ω | IDESATD = 200 mA | 35 | |
| Thermal resistance junction to ambient | RTHJA,OUT | 122 | K/W | @TA = 65°C, PD,OUT = 400 mW, PD,IN = 50 mW, 4 layer test PCB | 26 | ||
| Characterization parameter junction to package top, input side | ΨJtop | 8 | K/W | 26 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | pet | Maximum repetitive insulation voltage VIORM 1767 V (peak) | 44 |
CAD (KiCad official)
- Symbol:
1ED3860MC12MXUMA1 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
1ed3860mc12mxuma1-etched.step/1ed3860mc12mxuma1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);1ed3860mc12mxuma1.step/1ed3860mc12mxuma1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (46 pp, sha256
3af8d1dbf1447cd4, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).