Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

1ED3860MC12MXUMA1

Infineon Technologies · Gate Drive ICs · SOP-16

1ED3860MC12MXUMA1 from Infineon Technologies, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND1 power_in Reference ground of the input side; connect directly to the input signal ground.
2 VCC1 power_in Positive input-side supply, to be connected to 5 V or 3.3 V, with a decoupling capacitor placed close to this pin and GND1.
3 SCL input Clock input of the I2C bus, CMOS-compatible at 5 V or 3.3 V and referenced to GND1, with a pull-up resistor to VCC1.
4 SDA bidirectional Serial data I/O of the I2C bus (open-drain, CMOS) for 5 V or 3.3 V microcontroller I/O, referenced to GND1, with a pull-up resistor to VCC1.
5 RDYC bidirectional Open-drain combined ready output (high active), fault-clear input and soft-off input (low active), referenced to GND1 with an external pull-up to VCC1 (typically 2.2 kΩ).
6 FLT_N bidirectional Open-drain fault output (active low) and fault-off input (low active), referenced to GND1 with an external pull-up to VCC1 (typically 2.2 kΩ).
7 IN input Non-inverting gate driver input (5 V or 3.3 V CMOS) with an internal 40 kΩ pull-down that keeps the IGBT off if the pin is not connected.
8 GND1 power_in Reference ground of the input side; connect directly to the input signal ground.
9 VEE2 power_in Negative output-side supply, to be connected to 0 V to -25 V referenced to GND2; if no negative supply is used, all VEE2 pins must be connected to GND2.
10 CLAMP power_out Active Miller clamp output (high-current, connected directly to the IGBT gate), or clamp pre-driver output for an external n-channel MOSFET, or 8-bit ADC sense input between CLAMP and VEE2, depending on register configuration.
11 OFF power_out High-current driver sink output to discharge the IGBT gate through the turn-off gate resistor; it also sinks the soft-off current and serves as sense input for PINSTAT.OFF_PIN and TLTO_LVL.
12 ON power_out High-current driver source output to charge the IGBT gate through the turn-on gate resistor; it is also the sense input for the CLAMP function and PINSTAT.ON_PIN.
13 DESAT input Enhanced desaturation detection input referenced to GND2, connected to the IGBT collector through a protection resistor and high-voltage diode to monitor VCE.
14 VCC2 power_in Positive output-side supply, referenced to GND2, with decoupling capacitors placed close to VCC2-VEE2 and VCC2-GND2.
15 GND2 power_in Reference ground of the output side, connected to the common voltage of a bipolar supply and the IGBT emitter, with decoupling capacitors close to VCC2-GND2 and GND2-VEE2.
16 VEE2 power_in Negative output-side supply, to be connected to 0 V to -25 V referenced to GND2; if no negative supply is used, all VEE2 pins must be connected to GND2.

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package SOP-16
Category Power Management
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input to output offset voltage VOFFSET 2300 V VVEE2,max-VVEE2,min with VVEE2,max ≥ VGND1 ≥ VVEE2,min 25
Supply voltage input side VVCC1 -0.3 6.5 V 25
Logic input voltage (IN) VLogicIN -0.3 6.5 V 25
Logic input voltage (RDYC, FLT_N) VLogicRF -0.3 6.5 V 25
I2C logic input voltage (SDA, SCL) VLogicI2C -0.3 6.5 V 25
Open drain logic output current (RDYC, FLT_N) ILogicOC 10 mA 25
I2C logic output current (SDA) ISDA 50 mA 25
Positive supply voltage output side VVCC2 -0.3 40 V 25
Negative supply voltage output side VVEE2 -40 0.3 V 25
Maximum supply voltage difference output side (VVCC2 - VVEE2) Vmax2 40 V 25
DESAT input voltage (max printed as VVCC2 + 0.3 V; max value is the offset from VCC2) VDESAT -0.3 0.3 V 25
CLAMP input voltage (min printed as VVEE2 - 0.3 V; max as VVCC2 + 0.3 V; values are offsets from VEE2 and VCC2) VCLAMP -0.3 0.3 V 25
Maximum CLAMP output current ICLAMP 2.4 A t < 5 µs 25
Gate driver output voltage (ON, OFF) (min printed as VVEE2 - 0.3 V; max as Vmax2 + 0.3 V; values are offsets) VOUT -0.3 0.3 V 25
Maximum CLAMP to VCC2 diode IGBT short circuit clamping time tCLP 6 µs ICLAMP/OUT = 0.75 A 25
Junction temperature TJ -40 150 °C 25
Storage temperature TStg -55 150 °C 25
Power dissipation, input side PD,IN 100 mW @TA = 25 °C 25
Power dissipation, output side PD,OUT 700 mW @TA = 25°C 25
ESD capability: Human body model VESDHBM 2 kV 25
ESD capability: Charged device model VESDCDM 500 V 25
Supply voltage input side VVCC1 3 5.5 V 26
Logic input voltages (IN, RDYC, FLT_N, SDA, SCL) VLogicIN -0.3 5.5 V 26
Positive supply voltage output side VVCC2 13 25 V 26
Negative supply voltage output side VVEE2 -25 0 V 27
Supply voltage difference output side (VVCC2 - VVEE2) Vmax2 13 35 V 27
Ambient temperature TA -40 125 °C Note 2: TJ has to be below over temperature protection temperature TOTPOFF 27
Switching frequency fSW 0 250 kHz max PD applies 27
Common mode transient immunity /CMTI/ 0 200 V/ns VOFFSET,test = 1500 V 27
VCC1 UVLO threshold (rising) VUVLO1H 2.95 3.05 V 28
VCC1 UVLO threshold (falling) VUVLO1L 2.6 2.8 V 28
VCC1 UVLO hysteresis VHYS1 0.1 0.14 V 28
VCC1 quiescent current IQ1 2.4 4 mA VVCC1 = 3.3 V, IN = High, RDYC = High, FLT_N = High 28
VCC1 operating current IO1 2.4 4 mA VVCC1 = 3.3 V, IN = 16 kHz, 50%, RDYC = High, FLT_N = High, SCL = Low 28
VCC2 UVLO threshold (rising), setting 0H VUVLO2H,0 12 12.6 V UVTLVL.UVVCC2TL = 0H 28
VCC2 UVLO threshold (falling), setting 0H VUVLO2L,0 10.4 11 V 28
VCC2 UVLO hysteresis, setting 0H VHYS2,0 0.75 1 V 28
VCC2 UVLO threshold (rising), setting 1H VUVLO2H,1 9.4 10 V UVTLVL.UVVCC2TL = 1H 28
VCC2 UVLO threshold (falling), setting 1H VUVLO2L,1 8 8.7 V 28
VCC2 UVLO hysteresis, setting 1H VHYS2,1 0.6 0.7 V 28
VCC2 quiescent current IQ2 3.9 5 mA VVCC2 = 15 V, VVEE2 = -8 V, OUT = High, DESAT = Low, DRVCFG.STD_OFF = 0H, DRVFOFF = 00H/01H 29
VCC2 operating current IO2 3.9 5 mA VVCC2 = 15 V, VVEE2 = -8 V, OUT = 16 kHz, 50%, DESAT = Low, CLOAD = 100 pF, DRVCFG.STD_OFF = 0H, DRVFOFF = 00H/01H 29
High level clamp voltage (printed as VVCC2 + offset) VCLAMPH0 1.5 1.63 V ICLAMP = 500 mA 32
Clamp threshold voltage (related to VEE2) VON_CLAMP 1.5 2 2.5 V 32
Clamp-driver high level output peak current ICLAMPH 0.2 0.27 A VCC2 = 15 V; VEE2 = 0 V; CCLAMP = 100 nF; RCLAMP = 1 Ω 32
Clamp/Clamp-driver output low level current ICLAMPL,2 1.1 1.8 A VCC2 = 15 V; VEE2 = 0 V; VCLAMP = 2 V; CCLAMP = 100 nF; RCLAMP = 0.1 Ω 32
Clamp/Clamp-driver output low level current ICLAMPL,5 2.2 3.5 A VCC2 = 15 V; VEE2 = 0 V; VCLAMP = 5 V; CCLAMP = 100 nF; RCLAMP = 0.1 Ω 32
Clamp/Clamp-driver output low level ON resistance RDSON,CLP 0.5 0.85 1.35 Ω ICLAMPL = 200 mA 32
Input IN to output propagation delay ON tPDON 226 244 270 ns CLOAD = 100 pF, VIN = 70%, VOUT=20%, with tINMIN,0 34
Input IN to output propagation delay OFF tPDOFF 218 236 262 ns CLOAD = 100 pF, VIN = 30%, VOUT=80%, with tINMIN,0 34
Input to output propagation delay distortion (tPDOFF - tPDON) tPDISTO -23 -8 7 ns CLOAD = 100 pF 34
Input IN to output propagation delay distortion between any devices (tPDON-tPDON) or (tPDOFF-tPDOFF) tPDD 30 ns same conditions (VIN, VVCC1, VVCC2 and VVEE2, CLOAD, TA, tINMIN,0) 34
Input RDYC or FLT_N to TLTOff output propagation delay (1ED3860M) tPDRDYCT, tPDFLT_NT 360 417 482 ns 34
Rise time 1ED3860M tRISE 15 30 ns CLOAD = 2.2 nF, VOUT: 20% to 80% 35
Fall time 1ED3860M tFALL 15 30 ns CLOAD = 2.2 nF, VOUT: 80% to 20% 35
DESAT charge current IDESATC 470 500 525 µA VDESAT = 0 V 35
DESAT voltage divider resistance RDVD 259 312.5 366 kΩ between DESAT and GND2 pins 35
DESAT clamp and discharge ON resistance RDSON,D 7.7 25 Ω IDESATD = 200 mA 35
Thermal resistance junction to ambient RTHJA,OUT 122 K/W @TA = 65°C, PD,OUT = 400 mW, PD,IN = 50 mW, 4 layer test PCB 26
Characterization parameter junction to package top, input side ΨJtop 8 K/W 26

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing pet Maximum repetitive insulation voltage VIORM 1767 V (peak) 44

CAD (KiCad official)

  • Symbol: 1ED3860MC12MXUMA1
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOP-16 (KiCad packages3D, STEP)
  • 3D model files: 1ed3860mc12mxuma1-etched.step / 1ed3860mc12mxuma1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 1ed3860mc12mxuma1.step / 1ed3860mc12mxuma1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (46 pp, sha256 3af8d1dbf1447cd4, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF