component

100 nF Capacitor 0603 - Walsin 0603B104J500CT

Public Made by Adom Basic Part

by adom

0603 MLCC · 100 nF ±5% X7R · 50 V

Overview Files Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity
master
0603b104j500ct / README.md
History Download
John Lauer Footprint per the manufacturer's land pattern (ipc-fallback), derived viewers/lbr/hero rebuilt, lbr-hover on both viewe… a4dcc59 18d ago

100 nF Capacitor 0603 - Walsin 0603B104J500CT

Walsin Technology Corporation 0603B104J500CT: 0603 MLCC, 100 nF ±5% X7R, 50 V. An Adom Basic Part: Adom keeps it on reels for its pick-and-place line, so boards built with it draw on Adom stock.

Key specs

Spec Datasheet
0603 (1608 metric) multilayer ceramic chip capacitor, 1.60 × 0.80 × 0.80 mm body (+0.15/−0.10 mm, thickness code X), 0.40 mm termination bands; reflow or wave soldering p.3
100 nF ±5% (code 104 J), rated 50 VDC, X7R Class II dielectric, code B; listed in the X7R capacitance-range grid at 0603 / 50 V p.2, p.7
X7R temperature characteristic: capacitance within ±15% from −55 to +125 °C p.4, p.14
Dissipation factor ≤3% at 1 kHz / 1.0 Vrms; Class II parts get a 150 °C / 1 h de-aging plus 24 h rest before any measurement p.4, p.12
Insulation resistance 10 GΩ or R×C ≥ 500 Ω·F, whichever is smaller, at rated voltage p.14
Dielectric strength: withstands 250% of rated voltage for 1-5 s with no damage or flashover p.13
High-temperature load life: 1,000 h at 125 °C and 200% of rated voltage; capacitance change within ±12.5% p.18
BaTiO3-based ceramic, Ni inner electrodes, Cu/Ni/Sn termination (code C, pure-Sn outer plating) p.2, p.20
Paper carrier tape, 8 mm wide / 4 mm pocket pitch, 4,000 pcs per 7-inch (φ178 mm) reel, code T; store at 5-40 °C / 20-70% RH, MSL 1 p.11, p.19, p.20

Notes for designers

0603B104J500CT is a 0603 X7R capacitor from Walsin's General Purpose series: 100 nF ±5%, rated 50 VDC, decoded from the ordering table and confirmed in the X7R range grid. (p.2, p.7) It is a BaTiO3-based Class II ceramic, the approval sheet requires a 150 °C de-aging and 24 h rest before capacitance is even measured, a reminder that the label value is history- and drive-level-dependent. (p.4, p.20)

The numbers you design against: capacitance within ±15% from −55 to +125 °C, (p.4, p.14) dissipation factor ≤3% at 1 kHz / 1.0 Vrms, (p.12) insulation resistance 10 GΩ or R×C ≥ 500 Ω·F, (p.14) and a dielectric proofed at 250% of rated voltage. (p.13) Life testing runs 1,000 h at 125 °C and 200% of rated voltage with capacitance held within ±12.5%. (p.18) It ships 4,000 to a 7-inch paper-tape reel and is MSL 1. (p.11, p.20)

Footprint

The datasheet has no land pattern, so the pads are the IPC-7351 nominal pattern (KiCad's standard Capacitor_SMD:C_0603_1608Metric), replacing pads that were off it by up to 0.05 mm.

Source: IPC-7351 nominal (no land pattern in the datasheet): KiCad 10 Capacitor_SMD:C_0603_1608Metric pads.

mm Datasheet KiCad standard (C_0603_1608Metric) Previous This page
Pad length (along the part) none given 0.9 0.9 0.9
Pad width none given 0.95 1 0.95
Gap between pads none given 0.65 0.7 0.65
Centre to centre none given 1.55 1.6 1.55
Overall none given 2.45 2.5 2.45
Corner radius none given 0.225 (ratio 0.25) 0.225 (ratio 0.25) 0.1 (ratio 0.1111)

Corners: KiCad roundrects with the radius held to 0.25 x the smaller pad side and no more than 0.1 mm (IPC-7351C favours rounded corners for paste release); copper area within 1 % of a square-cornered pad.

Chip outline

The part's 3D outline in the standard pose (pad 1 toward the viewer), drawn from the STEP by Adom's OpenCascade service; the part number sits where the laser-etched mark is on the 3D model and reads the same way.

Symbol options

The default symbol is the plain standard symbol. 0603B104J500CT-outline.kicad_sym adds the chip outline beside it; the widget below builds other layouts in the browser and never changes the default.

Ordering
MPN 0603B104J500CT
Manufacturer Walsin Technology Corporation
Adom stock Adom Basic Part, stocked on reels for Adom's pick-and-place line; reel counts on pnp-inventory
Other sources adom-parts-search compares Mouser, DigiKey and JLCPCB

Downloads

File What it is
0603B104J500CT.kicad_sym KiCad symbol (standard symbol, the page default)
0603B104J500CT-outline.kicad_sym KiCad symbol with the 3D chip outline
0603B104J500CT.kicad_mod KiCad footprint (IPC-7351 nominal)
0603B104J500CT.step 3D STEP with the part number laser-etched (default)
0603B104J500CT-unetched.step 3D STEP, bare (no mark)
0603B104J500CT.glb 3D GLB of the etched model (board use)
0603B104J500CT.lbr Fusion 360 / EAGLE library
0603B104J500CT.adom-lbr.json adom-lbr part (converts to Altium, KiCad, EAGLE)
0603B104J500CT-datasheet.pdf Datasheet (release asset)

Provenance

  • Datasheet: MULTILAYER CERAMIC CAPACITORS General Purpose Series (4V to 100V), 0201 to 1812 Sizes, NP0, X7R, X6S, X7S & X5R Dielectrics - Approval Sheet, ASC_General Purpose Series revised Dec. 2023, Walsin Technology Corporation (Passive System Alliance). md5 0306337c43c3c7f2f7e91a237efddd14
  • Footprint: IPC-7351 nominal (no land pattern in the datasheet): KiCad 10 Capacitor_SMD:C_0603_1608Metric pads. Pads set to the IPC-7351 nominal pattern on 2026-10-03.
  • 3D model and symbol: unchanged by the footprint pass; the etched STEP adds a flat virtual part-number mark (an identification aid, not the maker's marking).
  • Earlier passes: provenance/ and CHANGES.md.

More