3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLSF0102DCTR
Texas Instruments · Translators / Level Shifters · SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch
LSF0102DCTR from Texas Instruments, in a SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground reference for the device. |
| 2 | Vref_A | power_in | Reference supply voltage for the A-side, operational from 0.95 V to 5.5 V and required to be the lowest voltage level across all inputs and outputs. |
| 3 | A1 | bidirectional | Auto-bidirectional data port on the low-side (A) channel 1; recommended input/output voltage range is 0 V to 5.5 V. |
| 4 | A2 | bidirectional | Auto-bidirectional data port on the low-side (A) channel 2; recommended input/output voltage range is 0 V to 5.5 V. |
| 5 | B2 | bidirectional | Auto-bidirectional data port on the high-side (B) channel 2; pull-up resistors are always required on the high side. |
| 6 | B1 | bidirectional | Auto-bidirectional data port on the high-side (B) channel 1; pull-up resistors are always required on the high side. |
| 7 | Vref_B | power_in | Reference supply for the B-side that biases the device, operational from 1.8 V to 5.5 V and recommended to be at least Vref_A + 0.8 V; a 0.1 µF filter capacitor is recommended. |
| 8 | EN | input | Enable input that must be tied directly to Vref_B and pulled up to VCCB through a 200 kΩ bias resistor; driving it LOW places all I/O pins in high impedance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch |
| Category | Logic |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input clamp voltage | VIK | -1.2 | V | II = -18mA, VEN = 0 | 6 | ||
| High-level input current | IIH | 5 | µA | VI = 5V, VEN = 0 | 6 | ||
| Supply current | ICC | 6 | µA | Vref_B = VEN = 5.5V, Vref_A = 4.5V, IO = 0, VI = VCC or GND | 6 | ||
| Input/output capacitance (off) | Cio(off) | 4 | 6 | pF | VO = 3V or 0, VEN = 0 | 6 | |
| Input/output capacitance (on) | Cio(on) | 10.5 | 12.5 | pF | VO = 3V or 0, VEN = 3V | 6 | |
| Reference input capacitance | CI(ref_A/B/EN) | 11 | pF | VI = 3V or 0 | 6 | ||
| On-state resistance, Vref_A = 3.3V, Vref_B = VEN = 5V | ron | 8 | Ω | VI = 0, IO = 64mA | 6 | ||
| On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 5V | ron | 9 | Ω | VI = 0, IO = 64mA | 6 | ||
| On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 5V | ron | 10 | Ω | VI = 0, IO = 64mA | 6 | ||
| On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 5V | ron | 10 | Ω | VI = 0, IO = 32mA | 6 | ||
| On-state resistance, Vref_A = 2.5V, Vref_B = VEN = 5V | ron | 15 | Ω | VI = 0, IO = 32mA | 6 | ||
| On-state resistance, Vref_A = 3.3V, Vref_B = VEN = 5V | ron | 9 | Ω | VI = 1.8V, IO = 15mA | 6 | ||
| On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 3.3V | ron | 18 | Ω | VI = 1.0V, IO = 10mA | 6 | ||
| On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 3.3V | ron | 20 | Ω | VI = 0V, IO = 10mA | 6 | ||
| On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 1.8V | ron | 30 | Ω | VI = 0V, IO = 10mA | 6 | ||
| Input/output voltage | VI/O | 0 | 5.5 | V | 5 | ||
| Reference voltage | Vref_A/B/EN | 0 | 5.5 | V | 5 | ||
| Pass transistor current | IPASS | 64 | mA | 5 | |||
| Operating free-air temperature | TA | -40 | 125 | °C | 5 | ||
| Reference voltage (A) | Vref_A | 0.9 | 5.5 | V | 18 | ||
| Input voltage | VI | -0.5 | 7 | V | 5 | ||
| Input/output voltage | VI/O | -0.5 | 7 | V | 5 | ||
| Continuous channel current | 128 | mA | 5 | ||||
| Input clamp current | IIK | -50 | mA | VI < 0 | 5 | ||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 5 | ||
| Junction-to-ambient thermal resistance (DCT) | RθJA | 220 | °C/W | DCT (SM8) 8-pin | 5 | ||
| Junction-to-case (top) thermal resistance (DCT) | RθJC(top) | 128.1 | °C/W | DCT (SM8) 8-pin | 5 | ||
| Junction-to-board thermal resistance (DCT) | RθJB | 135.6 | °C/W | DCT (SM8) 8-pin | 5 | ||
| Junction-to-top characterization parameter (DCT) | ψJT | 56 | °C/W | DCT (SM8) 8-pin | 5 | ||
| Junction-to-board characterization parameter (DCT) | ψJB | 134 | °C/W | DCT (SM8) 8-pin | 5 |
CAD (Adom-generated)
- Symbol:
LSF0102DCTR - Footprint:
Adom_Gen:Texas_Instruments_LSF0102_2543ce - 3D model: generated to fit the land (STEP)
- 3D model files:
lsf0102dctr-etched.step/lsf0102dctr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lsf0102dctr.step/lsf0102dctr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
4a9ba815d97f7478, retrieved 2026-11-18) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: TI DCT0008A Example Board Layout (lsf0102.pdf p.28, drawing 4220784): 8X (1.1) x 8X (0.4) pads, 6X (0.65) pitch, (3.8) between pad-row centres, read from this part's own sheet; land from part-reviewer's DCT0008A template (sn74lvc1g74dctr).