Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LSF0102DCTR

Texas Instruments · Translators / Level Shifters · SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch

LSF0102DCTR from Texas Instruments, in a SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 GND power_in Ground reference for the device.
2 Vref_A power_in Reference supply voltage for the A-side, operational from 0.95 V to 5.5 V and required to be the lowest voltage level across all inputs and outputs.
3 A1 bidirectional Auto-bidirectional data port on the low-side (A) channel 1; recommended input/output voltage range is 0 V to 5.5 V.
4 A2 bidirectional Auto-bidirectional data port on the low-side (A) channel 2; recommended input/output voltage range is 0 V to 5.5 V.
5 B2 bidirectional Auto-bidirectional data port on the high-side (B) channel 2; pull-up resistors are always required on the high side.
6 B1 bidirectional Auto-bidirectional data port on the high-side (B) channel 1; pull-up resistors are always required on the high side.
7 Vref_B power_in Reference supply for the B-side that biases the device, operational from 1.8 V to 5.5 V and recommended to be at least Vref_A + 0.8 V; a 0.1 µF filter capacitor is recommended.
8 EN input Enable input that must be tied directly to Vref_B and pulled up to VCCB through a 200 kΩ bias resistor; driving it LOW places all I/O pins in high impedance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-8 (TI DCT, SM8) 2.95 x 4 mm, 0.65 pitch
Category Logic
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input clamp voltage VIK -1.2 V II = -18mA, VEN = 0 6
High-level input current IIH 5 µA VI = 5V, VEN = 0 6
Supply current ICC 6 µA Vref_B = VEN = 5.5V, Vref_A = 4.5V, IO = 0, VI = VCC or GND 6
Input/output capacitance (off) Cio(off) 4 6 pF VO = 3V or 0, VEN = 0 6
Input/output capacitance (on) Cio(on) 10.5 12.5 pF VO = 3V or 0, VEN = 3V 6
Reference input capacitance CI(ref_A/B/EN) 11 pF VI = 3V or 0 6
On-state resistance, Vref_A = 3.3V, Vref_B = VEN = 5V ron 8 Ω VI = 0, IO = 64mA 6
On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 5V ron 9 Ω VI = 0, IO = 64mA 6
On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 5V ron 10 Ω VI = 0, IO = 64mA 6
On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 5V ron 10 Ω VI = 0, IO = 32mA 6
On-state resistance, Vref_A = 2.5V, Vref_B = VEN = 5V ron 15 Ω VI = 0, IO = 32mA 6
On-state resistance, Vref_A = 3.3V, Vref_B = VEN = 5V ron 9 Ω VI = 1.8V, IO = 15mA 6
On-state resistance, Vref_A = 1.8V, Vref_B = VEN = 3.3V ron 18 Ω VI = 1.0V, IO = 10mA 6
On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 3.3V ron 20 Ω VI = 0V, IO = 10mA 6
On-state resistance, Vref_A = 1.0V, Vref_B = VEN = 1.8V ron 30 Ω VI = 0V, IO = 10mA 6
Input/output voltage VI/O 0 5.5 V 5
Reference voltage Vref_A/B/EN 0 5.5 V 5
Pass transistor current IPASS 64 mA 5
Operating free-air temperature TA -40 125 °C 5
Reference voltage (A) Vref_A 0.9 5.5 V 18
Input voltage VI -0.5 7 V 5
Input/output voltage VI/O -0.5 7 V 5
Continuous channel current 128 mA 5
Input clamp current IIK -50 mA VI < 0 5
Junction temperature TJ 150 °C 5
Storage temperature range Tstg -65 150 °C 5
Junction-to-ambient thermal resistance (DCT) RθJA 220 °C/W DCT (SM8) 8-pin 5
Junction-to-case (top) thermal resistance (DCT) RθJC(top) 128.1 °C/W DCT (SM8) 8-pin 5
Junction-to-board thermal resistance (DCT) RθJB 135.6 °C/W DCT (SM8) 8-pin 5
Junction-to-top characterization parameter (DCT) ψJT 56 °C/W DCT (SM8) 8-pin 5
Junction-to-board characterization parameter (DCT) ψJB 134 °C/W DCT (SM8) 8-pin 5

CAD (Adom-generated)

  • Symbol: LSF0102DCTR
  • Footprint: Adom_Gen:Texas_Instruments_LSF0102_2543ce
  • 3D model: generated to fit the land (STEP)
  • 3D model files: lsf0102dctr-etched.step / lsf0102dctr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lsf0102dctr.step / lsf0102dctr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (42 pp, sha256 4a9ba815d97f7478, retrieved 2026-11-18)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: TI DCT0008A Example Board Layout (lsf0102.pdf p.28, drawing 4220784): 8X (1.1) x 8X (0.4) pads, 6X (0.65) pitch, (3.8) between pad-row centres, read from this part's own sheet; land from part-reviewer's DCT0008A template (sn74lvc1g74dctr).

Datasheet PDF