Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM4550BVH

Texas Instruments · Audio Interface ICs · LQFP-48(7x7)

LM4550BVH from Texas Instruments, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DVDD1 power_in Digital supply pin; DVDD operates from 3 V to 5.5 V per the recommended operating conditions.
2 XTL_IN input 24.576 MHz crystal or external oscillator input (standard logic levels), used only in Primary mode, with a 1 MΩ resistor across pins 2 and 3 when a crystal is fitted.
3 XTL_OUT output 24.576 MHz crystal output used with XTL_IN; left open (NC) when an external oscillator is used or when the codec is in a Secondary mode.
4 DVSS1 power_in Digital ground pin.
5 SDATA_OUT input AC Link output frame input from the AC '97 digital audio controller to the codec, sampled by the LM4550B on the falling edge of BIT_CLK.
6 BIT_CLK bidirectional AC Link clock: an output in Primary mode providing 12.288 MHz (the 24.576 MHz XTL_IN signal divided by two), and an input in any Secondary mode.
7 DVSS2 power_in Digital ground pin.
8 SDATA_IN output AC Link input frame output from the codec to the AC '97 controller, clocked by the LM4550B on the rising edge of BIT_CLK.
9 DVDD2 power_in Digital supply pin; DVDD operates from 3 V to 5.5 V per the recommended operating conditions.
10 SYNC input AC Link frame marker input defining 256-BIT_CLK frames (48 kHz positive pulse, 6.25% duty cycle), and also an active-high asynchronous Warm Reset input.
11 RESET# input Active-low Cold Reset input that must be used to initialize the LM4550B after power-on once the supplies have stabilized, returning registers and internal circuits to defaults.
12 PC_BEEP input Line-level mono input (1 Vrms nominal) mixed into the stereo mix with volume muted or adjustable from 0 dB to -45 dB in 3-dB steps, and switched directly to LINE_OUT during Cold Reset.
13 PHONE input Line-level mono input (1 Vrms nominal) selectable at the Record Select Mux or mixed into the stereo mix, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
14 AUX_L input Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
15 AUX_R input Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
16 VIDEO_L input Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
17 VIDEO_R input Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
18 CD_L input Left stereo line-level CD input (1 Vrms nominal) referenced to CD_GND, selectable for the left ADC or mixed into Stereo Mix 3D with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
19 CD_GND input AC ground reference for CD_L and CD_R that is not a DC ground and must be AC-coupled to the common stereo source ground.
20 CD_R input Right stereo line-level CD input (1 Vrms nominal) referenced to CD_GND, selectable for the right ADC or mixed into Stereo Mix 3D with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
21 MIC1 input Mono microphone input muxed to a boost amplifier with 0 dB or 20 dB gain (nominal input 1 Vrms or 0.1 Vrms respectively).
22 MIC2 input Mono microphone input muxed to a boost amplifier with 0 dB or 20 dB gain (nominal input 1 Vrms or 0.1 Vrms respectively).
23 LINE_IN_L input Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps.
24 LINE_IN_R input Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5 dB steps.
25 AVDD1 power_in Analog supply pin; AVDD operates from 4.2 V to 5.5 V per the recommended operating conditions.
26 AVSS1 power_in Analog ground pin.
27 VREF power_in Nominal 2.2 V internal reference that is not intended to source or sink current and should be bypassed with 3.3 µF and 0.1 µF on short traces.
28 VREF_OUT output Nominal 2.2 V reference output that can source up to 5 mA and can be used to bias a microphone.
29 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
30 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
31 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
32 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
33 3DP output Positive pin of the TI 3D Sound enhancement circuit, which requires a 0.022 µF capacitor between 3DP and 3DN and should be left open (NC) if 3D Sound is not needed.
34 3DN output Negative pin of the TI 3D Sound enhancement circuit, which requires a 0.022 µF capacitor between 3DP and 3DN and should be left open (NC) if 3D Sound is not needed.
35 LINE_OUT_L output Left stereo line-level output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Master Volume register.
36 LINE_OUT_R output Right stereo line-level output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Master Volume register.
37 MONO_OUT output Mono line-level output (1 Vrms nominal) fed from a microphone input or the mono sum of Stereo Mix 3D, with level muted or adjustable from 0 dB to -46.5 dB in 1.5-dB steps.
38 AVDD2 power_in Analog supply 2 pin; AVDD operates from 4.2 V to 5.5 V per the recommended operating conditions.
39 HP_OUT_L output Left stereo headphone output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Headphone Volume register.
40 HP_OUT_C input AC ground reference for HP_OUT_L and HP_OUT_R that must be capacitively coupled to analog ground with short traces and is not a DC ground.
41 HP_OUT_R output Right stereo headphone output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Headphone Volume register.
42 AVSS2 power_in Analog ground 2 pin.
43 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
44 NC unconnected Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground.
45 ID0# input Inverted-polarity Codec Identity pin: tying it to ground sets the ID0 bit to 1, tying it to DVDD sets it to 0, and leaving it open pulls it high internally.
46 ID1# input Inverted-polarity Codec Identity pin: tying it to ground sets the ID1 bit to 1, tying it to DVDD sets it to 0, and leaving it open pulls it high internally.
47 EAPD output External Amplifier Power-Down output set by the EAPD bit (D15) of register 26h, with its logic level set by DVDD and a default of 0 that enables the external amplifier.
48 CIN input Chain-In input that passes another codec's SDATA_IN through when the chain feature is used, and may be left open (NC) only when the chain feature is disabled.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package LQFP-48(7x7)
Category Communication Interface Chip
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Temperature range (operating free-air, TMIN to TMAX) TA -40 85 °C −40°C ≤ TA ≤ 85°C 8
Analog Supply Range AVDD 4.2 5.5 V 8
Digital Supply Range DVDD 3 5.5 V 8
Analog Supply Range (electrical characteristics) AVDD 4.2 5.5 V 9
Digital Supply Range (electrical characteristics) DVDD 3 5.5 V 9
Supply Voltage 6 V 8
Storage Temperature Tstg -65 150 °C 8
Input Voltage -0.3 V 8
Junction Temperature 150 °C 8
Soldering Information, LQFP package, vapor phase (60 sec) 215 °C Vapor phase, 60 sec 8
Soldering Information, LQFP package, infrared (15 sec) 220 °C Infrared, 15 sec 8
Digital Quiescent Power Supply Current DIDD 34 mA DVDD = 5 V 9
Digital Quiescent Power Supply Current DIDD 19 mA DVDD = 3.3 V 9
Analog Quiescent Power Supply Current AIDD 53 mA AVDD = 5 V 9
Digital Shutdown Current IDSD 19 µA PR6543210 = 1111111 9
Analog Shutdown Current IASD 70 µA PR6543210 = 1111111 9
Reference Voltage VREF 2.16 V No pullup resistor 9
Power Supply Rejection Ratio PSRR 40 dB 9
CD Input to Line Output Dynamic Range (THD+N) 90 97 dB -60 dB input, THD+N 9
Total Harmonic Distortion THD 0.013 0.02 % VO = -3 dB, f = 1 kHz, RL = 10 kΩ 9
Crosstalk Xtalk -95 dB CD Left to Right 9
Input Impedance ZIN 10 40 kΩ All Analog Inputs 9
Input Capacitance CIN 3.7 7 pF 9
Interchannel Gain Mismatch 0.1 dB CD Left to Right 9
Record Gain Mute Attenuation 86 dB 9
Mixer Section Mute Attenuation 86 dB 9
ADC Dynamic Range 86 90 dB -60-dB input THD+N, A-weighted 9
DAC Dynamic Range 82 89 dB -60-dB input THD+N, A-weighted 10
DAC Frequency Response 20 21 kHz 10
DAC Group Delay 0.36 1 ms Sample Freq. = 48 kHz 10
Out of Band Energy -40 dB 28.8 kHz to 100 kHz, relative to 1 Vrms DAC output (footnote 7) 10
Stop Band Rejection 70 dB 10
Discrete Tones DT -96 dB 10
Analog Output Mute Attenuation 86 dB 10
Headphone Amplifier THD+N 0.02 % Loopthrough mode; RL = 32 Ω, f = 1 kHz, Pout = 50 mW 10
Output Impedance HP_OUT_L, HP_OUT_R ZOUT 0.65 2.75 Ω HP_OUT_L, HP_OUT_R 10
Output Impedance LINE_OUT_L, LINE_OUT_R, MONO_OUT ZOUT 220 500 Ω LINE_OUT_L, LINE_OUT_R, MONO_OUT 10
Input Leakage Current IL -10 10 µA AC Link inputs 10
Tri-state Leakage Current IL -10 10 µA High impedance AC Link outputs 10
AC-Link I/O capacitance Cin 4 7.5 pF SDout, BitClk, SDin, Sync, Reset# only 10
Output drive current IDR 5 mA AC Link outputs 10
Thermal resistance, junction-to-ambient (RθJA) RθJA 74 °C/W 9
AD Resolution 18 Bits 9
DAC Resolution 18 Bits 10
Frequency Response, -1-dB Bandwidth 20 kHz 10
Record Gain AS Step Size AS 1.5 dB 0 dB to 22.5 dB 9
Mixer AS Step Size AS 1.5 dB 12 dB to -34.5 dB 9
Analog Output AS Step Size AS 1.5 dB 0 dB to -46.5 dB 10

CAD (KiCad official)

  • Symbol: LM4550BVH
  • Footprint: Package_QFP:LQFP-48_7x7mm_P0.5mm
  • 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: lm4550bvh-etched.step / lm4550bvh-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm4550bvh.step / lm4550bvh.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (48 pp, sha256 1a933ad130f95d0b, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF