component
LM4550BVH
Public Made by Adomby adom
Texas Instruments Audio Interface ICs, LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
LM4550BVH
Texas Instruments · Audio Interface ICs · LQFP-48(7x7)
LM4550BVH from Texas Instruments, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DVDD1 | power_in | Digital supply pin; DVDD operates from 3 V to 5.5 V per the recommended operating conditions. |
| 2 | XTL_IN | input | 24.576 MHz crystal or external oscillator input (standard logic levels), used only in Primary mode, with a 1 MΩ resistor across pins 2 and 3 when a crystal is fitted. |
| 3 | XTL_OUT | output | 24.576 MHz crystal output used with XTL_IN; left open (NC) when an external oscillator is used or when the codec is in a Secondary mode. |
| 4 | DVSS1 | power_in | Digital ground pin. |
| 5 | SDATA_OUT | input | AC Link output frame input from the AC '97 digital audio controller to the codec, sampled by the LM4550B on the falling edge of BIT_CLK. |
| 6 | BIT_CLK | bidirectional | AC Link clock: an output in Primary mode providing 12.288 MHz (the 24.576 MHz XTL_IN signal divided by two), and an input in any Secondary mode. |
| 7 | DVSS2 | power_in | Digital ground pin. |
| 8 | SDATA_IN | output | AC Link input frame output from the codec to the AC '97 controller, clocked by the LM4550B on the rising edge of BIT_CLK. |
| 9 | DVDD2 | power_in | Digital supply pin; DVDD operates from 3 V to 5.5 V per the recommended operating conditions. |
| 10 | SYNC | input | AC Link frame marker input defining 256-BIT_CLK frames (48 kHz positive pulse, 6.25% duty cycle), and also an active-high asynchronous Warm Reset input. |
| 11 | RESET# | input | Active-low Cold Reset input that must be used to initialize the LM4550B after power-on once the supplies have stabilized, returning registers and internal circuits to defaults. |
| 12 | PC_BEEP | input | Line-level mono input (1 Vrms nominal) mixed into the stereo mix with volume muted or adjustable from 0 dB to -45 dB in 3-dB steps, and switched directly to LINE_OUT during Cold Reset. |
| 13 | PHONE | input | Line-level mono input (1 Vrms nominal) selectable at the Record Select Mux or mixed into the stereo mix, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 14 | AUX_L | input | Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 15 | AUX_R | input | Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 16 | VIDEO_L | input | Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 17 | VIDEO_R | input | Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 18 | CD_L | input | Left stereo line-level CD input (1 Vrms nominal) referenced to CD_GND, selectable for the left ADC or mixed into Stereo Mix 3D with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 19 | CD_GND | input | AC ground reference for CD_L and CD_R that is not a DC ground and must be AC-coupled to the common stereo source ground. |
| 20 | CD_R | input | Right stereo line-level CD input (1 Vrms nominal) referenced to CD_GND, selectable for the right ADC or mixed into Stereo Mix 3D with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 21 | MIC1 | input | Mono microphone input muxed to a boost amplifier with 0 dB or 20 dB gain (nominal input 1 Vrms or 0.1 Vrms respectively). |
| 22 | MIC2 | input | Mono microphone input muxed to a boost amplifier with 0 dB or 20 dB gain (nominal input 1 Vrms or 0.1 Vrms respectively). |
| 23 | LINE_IN_L | input | Left stereo line-level input (1 Vrms nominal) selectable for the left ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5-dB steps. |
| 24 | LINE_IN_R | input | Right stereo line-level input (1 Vrms nominal) selectable for the right ADC or mixed into Stereo Mix 3D, with level adjustable from 12 dB to -34.5 dB in 1.5 dB steps. |
| 25 | AVDD1 | power_in | Analog supply pin; AVDD operates from 4.2 V to 5.5 V per the recommended operating conditions. |
| 26 | AVSS1 | power_in | Analog ground pin. |
| 27 | VREF | power_in | Nominal 2.2 V internal reference that is not intended to source or sink current and should be bypassed with 3.3 µF and 0.1 µF on short traces. |
| 28 | VREF_OUT | output | Nominal 2.2 V reference output that can source up to 5 mA and can be used to bias a microphone. |
| 29 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 30 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 31 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 32 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 33 | 3DP | output | Positive pin of the TI 3D Sound enhancement circuit, which requires a 0.022 µF capacitor between 3DP and 3DN and should be left open (NC) if 3D Sound is not needed. |
| 34 | 3DN | output | Negative pin of the TI 3D Sound enhancement circuit, which requires a 0.022 µF capacitor between 3DP and 3DN and should be left open (NC) if 3D Sound is not needed. |
| 35 | LINE_OUT_L | output | Left stereo line-level output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Master Volume register. |
| 36 | LINE_OUT_R | output | Right stereo line-level output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Master Volume register. |
| 37 | MONO_OUT | output | Mono line-level output (1 Vrms nominal) fed from a microphone input or the mono sum of Stereo Mix 3D, with level muted or adjustable from 0 dB to -46.5 dB in 1.5-dB steps. |
| 38 | AVDD2 | power_in | Analog supply 2 pin; AVDD operates from 4.2 V to 5.5 V per the recommended operating conditions. |
| 39 | HP_OUT_L | output | Left stereo headphone output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Headphone Volume register. |
| 40 | HP_OUT_C | input | AC ground reference for HP_OUT_L and HP_OUT_R that must be capacitively coupled to analog ground with short traces and is not a DC ground. |
| 41 | HP_OUT_R | output | Right stereo headphone output (1 Vrms nominal) fed from Stereo Mix, adjustable or muted from 0 dB to -46.5 dB in 1.5-dB steps through the Headphone Volume register. |
| 42 | AVSS2 | power_in | Analog ground 2 pin. |
| 43 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 44 | NC | unconnected | Not used; leave open (NC), or for second-source applications connect to a noise-free AVDD or AVSS supply or ground. |
| 45 | ID0# | input | Inverted-polarity Codec Identity pin: tying it to ground sets the ID0 bit to 1, tying it to DVDD sets it to 0, and leaving it open pulls it high internally. |
| 46 | ID1# | input | Inverted-polarity Codec Identity pin: tying it to ground sets the ID1 bit to 1, tying it to DVDD sets it to 0, and leaving it open pulls it high internally. |
| 47 | EAPD | output | External Amplifier Power-Down output set by the EAPD bit (D15) of register 26h, with its logic level set by DVDD and a default of 0 that enables the external amplifier. |
| 48 | CIN | input | Chain-In input that passes another codec's SDATA_IN through when the chain feature is used, and may be left open (NC) only when the chain feature is disabled. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-48(7x7) |
| Category | Communication Interface Chip |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature range (operating free-air, TMIN to TMAX) | TA | -40 | 85 | °C | −40°C ≤ TA ≤ 85°C | 8 | |
| Analog Supply Range | AVDD | 4.2 | 5.5 | V | 8 | ||
| Digital Supply Range | DVDD | 3 | 5.5 | V | 8 | ||
| Analog Supply Range (electrical characteristics) | AVDD | 4.2 | 5.5 | V | 9 | ||
| Digital Supply Range (electrical characteristics) | DVDD | 3 | 5.5 | V | 9 | ||
| Supply Voltage | 6 | V | 8 | ||||
| Storage Temperature | Tstg | -65 | 150 | °C | 8 | ||
| Input Voltage | -0.3 | V | 8 | ||||
| Junction Temperature | 150 | °C | 8 | ||||
| Soldering Information, LQFP package, vapor phase (60 sec) | 215 | °C | Vapor phase, 60 sec | 8 | |||
| Soldering Information, LQFP package, infrared (15 sec) | 220 | °C | Infrared, 15 sec | 8 | |||
| Digital Quiescent Power Supply Current | DIDD | 34 | mA | DVDD = 5 V | 9 | ||
| Digital Quiescent Power Supply Current | DIDD | 19 | mA | DVDD = 3.3 V | 9 | ||
| Analog Quiescent Power Supply Current | AIDD | 53 | mA | AVDD = 5 V | 9 | ||
| Digital Shutdown Current | IDSD | 19 | µA | PR6543210 = 1111111 | 9 | ||
| Analog Shutdown Current | IASD | 70 | µA | PR6543210 = 1111111 | 9 | ||
| Reference Voltage | VREF | 2.16 | V | No pullup resistor | 9 | ||
| Power Supply Rejection Ratio | PSRR | 40 | dB | 9 | |||
| CD Input to Line Output Dynamic Range (THD+N) | 90 | 97 | dB | -60 dB input, THD+N | 9 | ||
| Total Harmonic Distortion | THD | 0.013 | 0.02 | % | VO = -3 dB, f = 1 kHz, RL = 10 kΩ | 9 | |
| Crosstalk | Xtalk | -95 | dB | CD Left to Right | 9 | ||
| Input Impedance | ZIN | 10 | 40 | kΩ | All Analog Inputs | 9 | |
| Input Capacitance | CIN | 3.7 | 7 | pF | 9 | ||
| Interchannel Gain Mismatch | 0.1 | dB | CD Left to Right | 9 | |||
| Record Gain Mute Attenuation | 86 | dB | 9 | ||||
| Mixer Section Mute Attenuation | 86 | dB | 9 | ||||
| ADC Dynamic Range | 86 | 90 | dB | -60-dB input THD+N, A-weighted | 9 | ||
| DAC Dynamic Range | 82 | 89 | dB | -60-dB input THD+N, A-weighted | 10 | ||
| DAC Frequency Response | 20 | 21 | kHz | 10 | |||
| DAC Group Delay | 0.36 | 1 | ms | Sample Freq. = 48 kHz | 10 | ||
| Out of Band Energy | -40 | dB | 28.8 kHz to 100 kHz, relative to 1 Vrms DAC output (footnote 7) | 10 | |||
| Stop Band Rejection | 70 | dB | 10 | ||||
| Discrete Tones | DT | -96 | dB | 10 | |||
| Analog Output Mute Attenuation | 86 | dB | 10 | ||||
| Headphone Amplifier THD+N | 0.02 | % | Loopthrough mode; RL = 32 Ω, f = 1 kHz, Pout = 50 mW | 10 | |||
| Output Impedance HP_OUT_L, HP_OUT_R | ZOUT | 0.65 | 2.75 | Ω | HP_OUT_L, HP_OUT_R | 10 | |
| Output Impedance LINE_OUT_L, LINE_OUT_R, MONO_OUT | ZOUT | 220 | 500 | Ω | LINE_OUT_L, LINE_OUT_R, MONO_OUT | 10 | |
| Input Leakage Current | IL | -10 | 10 | µA | AC Link inputs | 10 | |
| Tri-state Leakage Current | IL | -10 | 10 | µA | High impedance AC Link outputs | 10 | |
| AC-Link I/O capacitance | Cin | 4 | 7.5 | pF | SDout, BitClk, SDin, Sync, Reset# only | 10 | |
| Output drive current | IDR | 5 | mA | AC Link outputs | 10 | ||
| Thermal resistance, junction-to-ambient (RθJA) | RθJA | 74 | °C/W | 9 | |||
| AD Resolution | 18 | Bits | 9 | ||||
| DAC Resolution | 18 | Bits | 10 | ||||
| Frequency Response, -1-dB Bandwidth | 20 | kHz | 10 | ||||
| Record Gain AS Step Size | AS | 1.5 | dB | 0 dB to 22.5 dB | 9 | ||
| Mixer AS Step Size | AS | 1.5 | dB | 12 dB to -34.5 dB | 9 | ||
| Analog Output AS Step Size | AS | 1.5 | dB | 0 dB to -46.5 dB | 10 |
CAD (KiCad official)
- Symbol:
LM4550BVH - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
lm4550bvh-etched.step/lm4550bvh-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm4550bvh.step/lm4550bvh.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
1a933ad130f95d0b, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).