Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL78229ARZ-T7A

RENESAS · DC-DC Controllers · TQFN-40-EP(6x6)

ISL78229ARZ-T7A from RENESAS, in a TQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SLOPE passive Programs the internal slope compensation slope via a resistor connected from SLOPE to GND.
2 FB input Inverting input of the voltage-loop error amplifier, set by a resistor network to VOUT, also feeds the output OV and UV comparators.
3 COMP output Output of the transconductance error amplifier Gm1 for the voltage loop, with the compensation network placed between COMP and ground.
4 SS passive A capacitor from SS to ground sets the soft-start ramp rate and soft-start time (5µA charging current).
5 IMON output Average current monitor output for the sum of the two phase inductor currents (sum of CSA outputs plus 17µA offset), used for average current limiting and protection (fault above 2V).
6 TRACK input External reference input for the output voltage loop, analog or digital per ATRK/DTRK, connected to VCC if unused.
7 ADDR1 input Logic input that with ADDR2 selects one of four PMBus slave addresses.
8 ADDR2 input Logic input that with ADDR1 selects one of four PMBus slave addresses.
9 PGOOD output Open-drain power-good output, pulled up to VCC, high when output is within OV/UV thresholds and soft-start is completed.
10 FSYNC bidirectional Sets switching frequency (50kHz to 1.1MHz) via a resistor to ground, or synchronizes to an external clock (minimum pulse width 20ns).
11 SGND power_in Signal ground for internal sensitive analog circuits, connect to a large quiet copper ground plane.
12 SDA bidirectional Serial bus data input/output that requires a pull-up.
13 SCL input Serial bus clock input that requires a pull-up.
14 SALERT output PMBus alert open-drain output pulled low when a fault is detected, requires a pull-up.
15 NTC input External temperature sensor input with 20µA current source out of the pin through an NTC resistor to GND, read by the internal ADC.
16 DE/PHDRP input Selects Diode Emulation, DE plus phase dropping, or CCM mode (VCC, FLOAT, or GND).
17 RBLANK passive A resistor to ground programs the current-sense blanking time (minimum on-time) after LG turns on.
18 PLLCOMP passive Compensation node for the switching clock PLL, using a second-order passive loop filter to ground.
19 EN input Threshold-sensitive enable input, enables above 1.2V and disables below 0.95V clearing all fault states.
20 CLKOUT output Clock output at one phase's switching frequency delayed 90° from LG1 rising edge, for 4-phase operation via the second IC's FSYNC.
21 BOOT2 power_in Bias supply for the Phase 2 high-side driver, with recommended 0.47µF capacitor in series with 1.5Ω to PH2, or tied to ground to disable high-side drivers.
22 UG2 output Phase 2 high-side gate driver output.
23 PH2 passive Phase 2 high-side gate drive return, connected to the high-side MOSFET source and low-side MOSFET drain.
24 LG2 output Phase 2 low-side gate driver output connected to the Phase 2 low-side MOSFET gates.
25 PGND power_in Return path for the low-side MOSFET drivers, connected to the ground plane through several vias close to the IC.
26 PVCC power_out Output of the internal linear regulator biasing drivers and VCC, operating range 4.75V to 5.5V with minimum 10µF decoupling to PGND.
27 LG1 output Phase 1 low-side gate driver output connected to the Phase 1 low-side MOSFET gates.
28 PH1 passive Phase 1 high-side gate drive return, connected to the high-side MOSFET source and low-side MOSFET drain.
29 UG1 output Phase 1 high-side MOSFET gate drive output.
30 BOOT1 power_in Bias supply for the Phase 1 high-side driver, with recommended 0.47µF capacitor in series with 1.5Ω to PH1, or tied to ground to disable high-side drivers.
31 VIN power_in Supply input to the internal linear regulator, not to exceed 55V in normal operation and withstands transients up to 60V.
32 ISEN1N input Negative input to the Phase 1 current sense amplifier sensing inductor current through a series sense resistor.
33 ISEN1P input Positive input to the Phase 1 current sense amplifier.
34 ISEN2N input Negative input to the Phase 2 current sense amplifier sensing inductor current through a series sense resistor.
35 ISEN2P input Positive input to the Phase 2 current sense amplifier.
36 NC unconnected Not electrically connected internally.
37 HIC/LATCH input Selects Hiccup (HIGH) or Latch-off (LOW) response to faults.
38 ATRK/DTRK input Selects TRACK pin input format, HIGH for analog and LOW for digital signals.
39 RDT passive A resistor to ground programs the dead times between UGx and LGx transitions to prevent shoot-through.
40 VCC power_in Bias power input for internal analog circuitry, 4.75V to 5.5V, with minimum 1µF ceramic decoupling.
41 PAD passive Bottom thermal pad, not an electrical connection, to be connected to a large PCB ground copper plane with multiple vias.

Key specifications

Parameter Value
Manufacturer RENESAS
Package TQFN-40-EP(6x6)
Category Power Supply Chip
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 5 55 V Switching, internal LDO dropout (VIN - PVCC) less than 0.25V 9
Input Supply Current (switching) IQ_SW 8 10 mA EN = 5V, VIN = 12V, RFSYNC = 40.2k (fSW = 300kHz), LGx = UGx = OPEN 9
Input Supply Current (non-switching) IQ_NON-SW 6 8.5 mA EN = 5V, VIN = 12V, non-switching, LGx = UGx = OPEN 9
Shutdown Supply Current to VIN I_SD_VIN_55V 0.2 1 µA EN = GND, VIN = 55V 9
ISENx Shutdown Bias Current I_SD_ISENxP/N -1 0 1 µA EN = GND, VIN = 55V, ISENx pin = 55V 9
VIN OVP Rising Threshold 56.5 58 59.5 V EN = 5V, VIN rising 9
LDO Voltage (PVCC) VPVCC 5 5.2 5.4 V VIN = 6V to 55V, CPVCC = 4.7µF, IPVCC = 10mA 9
LDO Current Limit IOC_LDO 130 195 250 mA VIN = 6V, VPVCC = 4.5V 9
LDO Output Short Current Limit IOCFB_LDO 50 100 160 mA VIN = 6V, VPVCC = 0V 9
Rising VCC POR Threshold VPORH_VCC 4.35 4.5 4.75 V 10
Falling VCC POR Threshold VPORL_VCC 4.05 4.15 4.25 V 10
Rising PVCC POR Threshold VPORH_PVCC 4.35 4.5 4.75 V 10
Falling PVCC POR Threshold VPORL_PVCC 3 3.2 3.4 V 10
Enable Threshold Rising VENH 1.13 1.21 1.33 V EN rising 10
Enable Threshold Falling VENL 0.85 0.95 1.1 V EN falling 10
EN Input Impedance 2 6 MΩ EN = 4V 10
PWM Switching Frequency FOSC 46 50.2 54.5 kHz RFSYNC = 249kΩ (0.1%) 10
PWM Switching Frequency FOSC 142 150 156 kHz RFSYNC = 82.5kΩ (0.1%) 10
PWM Switching Frequency FOSC 290 300 310 kHz RFSYNC = 40.2kΩ (0.1%) 10
PWM Switching Frequency FOSC 990 1100 1170 kHz RFSYNC = 10kΩ (0.1%) 10
Minimum ON-Time tMINON_1 315 410 525 ns Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 80kΩ (0.1%) 10
Minimum ON-Time tMINON_2 175 260 325 ns Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 50kΩ (0.1%) 10
Minimum ON-Time tMINON_3 100 140 180 ns Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 25kΩ (0.1%) 10
Minimum ON-Time tMINON_4 75 90 105 ns Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 10k 10
Maximum Duty Cycle DMAX 88.5 89 90.5 % VCOMP = 3.5V, fSW = 300kHz, RDT = 18.2kΩ, CUG = CLG = OPEN 10
Soft-Start Current ISS 4.5 5 5.5 µA 11
Soft-Start Prebias Voltage Accuracy -25 0 25 mV VFB = 500mV 11
Soft-Start Clamp Voltage VSSCLAMP 3.25 3.47 3.7 V 11
System Reference Accuracy 1.576 1.6 1.62 V Measured at the FB pin 11
FB Pin Input Bias Current -0.05 0.01 0.05 µA VFB = 1.6V, TRACK = Open 11
Gm1 Maximum Output Voltage 3.5 3.7 V 11
Gm1 Minimum Output Voltage 0.1 0.3 V 11
SLOPE Pin Voltage 480 500 520 mV 11
SLOPE Accuracy -20 0 20 % RSLOPE = 20k (0.1%) 11
SLOPE Accuracy -20 3 20 % RSLOPE = 40.2k (0.1%) 11
ISENxP/ISENxN Bias Current ISENxP/N_BIAS 100 123 150 µA Sourcing out of pin, EN = 5V, VISENxN = VISENxP, VCM = 4V to 55V 12
Zero Crossing Detection Threshold VZCD_CSA -4 1.3 6 mV RSET = 665Ω (0.1%) 12
VIMON Phase-Drop Falling Threshold VPHDRP_TH_F 1 1.1 1.2 V Drop off Phase 2 12
VIMON Phase-Add Rising Threshold VPHADD_TH_R 1.05 1.15 1.25 V Add back Phase 2 12
VIMON Phase-Drop Threshold Hysteresis VPHDRP_HYS 45 50 55 mV 12
Peak Current Cycle-by-Cycle Limit Threshold VOC1 40 53 65 mV IOC1_TH = 80µA, RSETx = 665Ω (0.1%) 12
Peak Current Fault Protection Threshold VOC2 55 70 85 mV IOC2_TH = 105µA, RSETx = 665Ω (0.1%) 12
IMON Current Accuracy 27 28.3 29.5 µA VRSENx = 30mV, RSETx = 665Ω (0.1%), ISENxP/N at 4V or 55V CM 13
IMON Offset Current 16 17 18 µA VRSENx = 0V, RSET = 665Ω (0.1%) 13
Constant Current Control Reference Accuracy VREFCC 1.575 1.6 1.625 V Measure the IMON pin 13
OC_AVG Fault Threshold at IMON 1.9 2 2.1 V 13
BOOT-PH UVLO Detection Threshold 2.8 3 3.2 V 13
BOOT-PH UVLO Hysteresis 0.09 0.15 0.22 V 13
Dead Time UG Falling to LG Rising tDT1 55 70 85 ns CUG = CLG = OPEN, RDT = 10k (0.1%) 13
Dead Time LG Falling to UG Rising tDT2 65 80 95 ns CUG = CLG = OPEN, RDT = 10k (0.1%) 13
Dead Time UG Falling to LG Rising tDT1 85 100 115 ns CUG = CLG = OPEN, RDT = 18.2kΩ (0.1%) 13
Dead Time LG Falling to UG Rising tDT2 95 110 125 ns CUG = CLG = OPEN, RDT = 18.2kΩ (0.1%) 13
Dead Time UG Falling to LG Rising tDT1 185 210 240 ns CUG = CLG = OPEN, RDT = 50kΩ (0.1%) 13
Dead Time LG Falling to UG Rising tDT2 205 230 260 ns CUG = CLG = OPEN, RDT = 50kΩ (0.1%) 13
Dead Time UG Falling to LG Rising tDT1 235 265 295 ns CUG = CLG = OPEN, RDT = 64.9kΩ (0.1%) 13
Dead Time LG Falling to UG Rising tDT2 260 290 320 ns CUG = CLG = OPEN, RDT = 64.9kΩ (0.1%) 13
FB Overvoltage Rising Trip Threshold VFBOV_RISE 118 120 122 % Percentage of VDAC output reference (default VREF = 1.6V) 13
FB Overvoltage Falling Recovery Threshold VFBOV_FALL 114 116 118 % Percentage of VDAC output reference (default VREF = 1.6V) 13
Undervoltage Falling Trip Threshold VFBUVREF_FALL 78 80 82 % Percentage of VDAC output reference (default VREF = 1.6V) 14
Undervoltage Rising Recovery Threshold VFBUVREF_RISE 82.5 84 86.5 % Percentage of VDAC output reference (default VREF = 1.6V) 14
PGOOD Low Voltage 0.06 0.4 V PGOOD LOW, IPGOOD = 0.5mA 14
NTC Output Sourcing Current 19 20 21 µA EN >2V, pin voltage = 0V 15
Operational Junction Temperature Range TJ -40 125 °C Automotive 9
PVCC, VCC Operating Voltage PVCC, VCC 4.75 5.5 V 9
VIN Absolute Maximum VIN -0.3 60 V 9
Thermal Resistance Junction-Ambient θJA 28 °C/W 40 Ld 6x6 WFQFN, Notes 4, 5 9
Thermal Resistance Junction-Case θJC 1.2 °C/W 40 Ld 6x6 WFQFN, Notes 4, 5 9

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper SGND 11 Signal ground pin that the internal sensitive analog circuits refer to. Connect this pin to a large copper ground plane free 4

CAD (KiCad official)

  • Symbol: ISL78229ARZ-T7A
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: TQFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: isl78229arz-t7a-etched.step / isl78229arz-t7a-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl78229arz-t7a.step / isl78229arz-t7a.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (72 pp, sha256 bf1d64560e236c82, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF