3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownISL78229ARZ-T7A
RENESAS · DC-DC Controllers · TQFN-40-EP(6x6)
ISL78229ARZ-T7A from RENESAS, in a TQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SLOPE | passive | Programs the internal slope compensation slope via a resistor connected from SLOPE to GND. |
| 2 | FB | input | Inverting input of the voltage-loop error amplifier, set by a resistor network to VOUT, also feeds the output OV and UV comparators. |
| 3 | COMP | output | Output of the transconductance error amplifier Gm1 for the voltage loop, with the compensation network placed between COMP and ground. |
| 4 | SS | passive | A capacitor from SS to ground sets the soft-start ramp rate and soft-start time (5µA charging current). |
| 5 | IMON | output | Average current monitor output for the sum of the two phase inductor currents (sum of CSA outputs plus 17µA offset), used for average current limiting and protection (fault above 2V). |
| 6 | TRACK | input | External reference input for the output voltage loop, analog or digital per ATRK/DTRK, connected to VCC if unused. |
| 7 | ADDR1 | input | Logic input that with ADDR2 selects one of four PMBus slave addresses. |
| 8 | ADDR2 | input | Logic input that with ADDR1 selects one of four PMBus slave addresses. |
| 9 | PGOOD | output | Open-drain power-good output, pulled up to VCC, high when output is within OV/UV thresholds and soft-start is completed. |
| 10 | FSYNC | bidirectional | Sets switching frequency (50kHz to 1.1MHz) via a resistor to ground, or synchronizes to an external clock (minimum pulse width 20ns). |
| 11 | SGND | power_in | Signal ground for internal sensitive analog circuits, connect to a large quiet copper ground plane. |
| 12 | SDA | bidirectional | Serial bus data input/output that requires a pull-up. |
| 13 | SCL | input | Serial bus clock input that requires a pull-up. |
| 14 | SALERT | output | PMBus alert open-drain output pulled low when a fault is detected, requires a pull-up. |
| 15 | NTC | input | External temperature sensor input with 20µA current source out of the pin through an NTC resistor to GND, read by the internal ADC. |
| 16 | DE/PHDRP | input | Selects Diode Emulation, DE plus phase dropping, or CCM mode (VCC, FLOAT, or GND). |
| 17 | RBLANK | passive | A resistor to ground programs the current-sense blanking time (minimum on-time) after LG turns on. |
| 18 | PLLCOMP | passive | Compensation node for the switching clock PLL, using a second-order passive loop filter to ground. |
| 19 | EN | input | Threshold-sensitive enable input, enables above 1.2V and disables below 0.95V clearing all fault states. |
| 20 | CLKOUT | output | Clock output at one phase's switching frequency delayed 90° from LG1 rising edge, for 4-phase operation via the second IC's FSYNC. |
| 21 | BOOT2 | power_in | Bias supply for the Phase 2 high-side driver, with recommended 0.47µF capacitor in series with 1.5Ω to PH2, or tied to ground to disable high-side drivers. |
| 22 | UG2 | output | Phase 2 high-side gate driver output. |
| 23 | PH2 | passive | Phase 2 high-side gate drive return, connected to the high-side MOSFET source and low-side MOSFET drain. |
| 24 | LG2 | output | Phase 2 low-side gate driver output connected to the Phase 2 low-side MOSFET gates. |
| 25 | PGND | power_in | Return path for the low-side MOSFET drivers, connected to the ground plane through several vias close to the IC. |
| 26 | PVCC | power_out | Output of the internal linear regulator biasing drivers and VCC, operating range 4.75V to 5.5V with minimum 10µF decoupling to PGND. |
| 27 | LG1 | output | Phase 1 low-side gate driver output connected to the Phase 1 low-side MOSFET gates. |
| 28 | PH1 | passive | Phase 1 high-side gate drive return, connected to the high-side MOSFET source and low-side MOSFET drain. |
| 29 | UG1 | output | Phase 1 high-side MOSFET gate drive output. |
| 30 | BOOT1 | power_in | Bias supply for the Phase 1 high-side driver, with recommended 0.47µF capacitor in series with 1.5Ω to PH1, or tied to ground to disable high-side drivers. |
| 31 | VIN | power_in | Supply input to the internal linear regulator, not to exceed 55V in normal operation and withstands transients up to 60V. |
| 32 | ISEN1N | input | Negative input to the Phase 1 current sense amplifier sensing inductor current through a series sense resistor. |
| 33 | ISEN1P | input | Positive input to the Phase 1 current sense amplifier. |
| 34 | ISEN2N | input | Negative input to the Phase 2 current sense amplifier sensing inductor current through a series sense resistor. |
| 35 | ISEN2P | input | Positive input to the Phase 2 current sense amplifier. |
| 36 | NC | unconnected | Not electrically connected internally. |
| 37 | HIC/LATCH | input | Selects Hiccup (HIGH) or Latch-off (LOW) response to faults. |
| 38 | ATRK/DTRK | input | Selects TRACK pin input format, HIGH for analog and LOW for digital signals. |
| 39 | RDT | passive | A resistor to ground programs the dead times between UGx and LGx transitions to prevent shoot-through. |
| 40 | VCC | power_in | Bias power input for internal analog circuitry, 4.75V to 5.5V, with minimum 1µF ceramic decoupling. |
| 41 | PAD | passive | Bottom thermal pad, not an electrical connection, to be connected to a large PCB ground copper plane with multiple vias. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TQFN-40-EP(6x6) |
| Category | Power Supply Chip |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 5 | 55 | V | Switching, internal LDO dropout (VIN - PVCC) less than 0.25V | 9 | |
| Input Supply Current (switching) | IQ_SW | 8 | 10 | mA | EN = 5V, VIN = 12V, RFSYNC = 40.2k (fSW = 300kHz), LGx = UGx = OPEN | 9 | |
| Input Supply Current (non-switching) | IQ_NON-SW | 6 | 8.5 | mA | EN = 5V, VIN = 12V, non-switching, LGx = UGx = OPEN | 9 | |
| Shutdown Supply Current to VIN | I_SD_VIN_55V | 0.2 | 1 | µA | EN = GND, VIN = 55V | 9 | |
| ISENx Shutdown Bias Current | I_SD_ISENxP/N | -1 | 0 | 1 | µA | EN = GND, VIN = 55V, ISENx pin = 55V | 9 |
| VIN OVP Rising Threshold | 56.5 | 58 | 59.5 | V | EN = 5V, VIN rising | 9 | |
| LDO Voltage (PVCC) | VPVCC | 5 | 5.2 | 5.4 | V | VIN = 6V to 55V, CPVCC = 4.7µF, IPVCC = 10mA | 9 |
| LDO Current Limit | IOC_LDO | 130 | 195 | 250 | mA | VIN = 6V, VPVCC = 4.5V | 9 |
| LDO Output Short Current Limit | IOCFB_LDO | 50 | 100 | 160 | mA | VIN = 6V, VPVCC = 0V | 9 |
| Rising VCC POR Threshold | VPORH_VCC | 4.35 | 4.5 | 4.75 | V | 10 | |
| Falling VCC POR Threshold | VPORL_VCC | 4.05 | 4.15 | 4.25 | V | 10 | |
| Rising PVCC POR Threshold | VPORH_PVCC | 4.35 | 4.5 | 4.75 | V | 10 | |
| Falling PVCC POR Threshold | VPORL_PVCC | 3 | 3.2 | 3.4 | V | 10 | |
| Enable Threshold Rising | VENH | 1.13 | 1.21 | 1.33 | V | EN rising | 10 |
| Enable Threshold Falling | VENL | 0.85 | 0.95 | 1.1 | V | EN falling | 10 |
| EN Input Impedance | 2 | 6 | MΩ | EN = 4V | 10 | ||
| PWM Switching Frequency | FOSC | 46 | 50.2 | 54.5 | kHz | RFSYNC = 249kΩ (0.1%) | 10 |
| PWM Switching Frequency | FOSC | 142 | 150 | 156 | kHz | RFSYNC = 82.5kΩ (0.1%) | 10 |
| PWM Switching Frequency | FOSC | 290 | 300 | 310 | kHz | RFSYNC = 40.2kΩ (0.1%) | 10 |
| PWM Switching Frequency | FOSC | 990 | 1100 | 1170 | kHz | RFSYNC = 10kΩ (0.1%) | 10 |
| Minimum ON-Time | tMINON_1 | 315 | 410 | 525 | ns | Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 80kΩ (0.1%) | 10 |
| Minimum ON-Time | tMINON_2 | 175 | 260 | 325 | ns | Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 50kΩ (0.1%) | 10 |
| Minimum ON-Time | tMINON_3 | 100 | 140 | 180 | ns | Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 25kΩ (0.1%) | 10 |
| Minimum ON-Time | tMINON_4 | 75 | 90 | 105 | ns | Minimum duty cycle, CUG = CLG = OPEN, RBLANK = 10k | 10 |
| Maximum Duty Cycle | DMAX | 88.5 | 89 | 90.5 | % | VCOMP = 3.5V, fSW = 300kHz, RDT = 18.2kΩ, CUG = CLG = OPEN | 10 |
| Soft-Start Current | ISS | 4.5 | 5 | 5.5 | µA | 11 | |
| Soft-Start Prebias Voltage Accuracy | -25 | 0 | 25 | mV | VFB = 500mV | 11 | |
| Soft-Start Clamp Voltage | VSSCLAMP | 3.25 | 3.47 | 3.7 | V | 11 | |
| System Reference Accuracy | 1.576 | 1.6 | 1.62 | V | Measured at the FB pin | 11 | |
| FB Pin Input Bias Current | -0.05 | 0.01 | 0.05 | µA | VFB = 1.6V, TRACK = Open | 11 | |
| Gm1 Maximum Output Voltage | 3.5 | 3.7 | V | 11 | |||
| Gm1 Minimum Output Voltage | 0.1 | 0.3 | V | 11 | |||
| SLOPE Pin Voltage | 480 | 500 | 520 | mV | 11 | ||
| SLOPE Accuracy | -20 | 0 | 20 | % | RSLOPE = 20k (0.1%) | 11 | |
| SLOPE Accuracy | -20 | 3 | 20 | % | RSLOPE = 40.2k (0.1%) | 11 | |
| ISENxP/ISENxN Bias Current | ISENxP/N_BIAS | 100 | 123 | 150 | µA | Sourcing out of pin, EN = 5V, VISENxN = VISENxP, VCM = 4V to 55V | 12 |
| Zero Crossing Detection Threshold | VZCD_CSA | -4 | 1.3 | 6 | mV | RSET = 665Ω (0.1%) | 12 |
| VIMON Phase-Drop Falling Threshold | VPHDRP_TH_F | 1 | 1.1 | 1.2 | V | Drop off Phase 2 | 12 |
| VIMON Phase-Add Rising Threshold | VPHADD_TH_R | 1.05 | 1.15 | 1.25 | V | Add back Phase 2 | 12 |
| VIMON Phase-Drop Threshold Hysteresis | VPHDRP_HYS | 45 | 50 | 55 | mV | 12 | |
| Peak Current Cycle-by-Cycle Limit Threshold | VOC1 | 40 | 53 | 65 | mV | IOC1_TH = 80µA, RSETx = 665Ω (0.1%) | 12 |
| Peak Current Fault Protection Threshold | VOC2 | 55 | 70 | 85 | mV | IOC2_TH = 105µA, RSETx = 665Ω (0.1%) | 12 |
| IMON Current Accuracy | 27 | 28.3 | 29.5 | µA | VRSENx = 30mV, RSETx = 665Ω (0.1%), ISENxP/N at 4V or 55V CM | 13 | |
| IMON Offset Current | 16 | 17 | 18 | µA | VRSENx = 0V, RSET = 665Ω (0.1%) | 13 | |
| Constant Current Control Reference Accuracy | VREFCC | 1.575 | 1.6 | 1.625 | V | Measure the IMON pin | 13 |
| OC_AVG Fault Threshold at IMON | 1.9 | 2 | 2.1 | V | 13 | ||
| BOOT-PH UVLO Detection Threshold | 2.8 | 3 | 3.2 | V | 13 | ||
| BOOT-PH UVLO Hysteresis | 0.09 | 0.15 | 0.22 | V | 13 | ||
| Dead Time UG Falling to LG Rising | tDT1 | 55 | 70 | 85 | ns | CUG = CLG = OPEN, RDT = 10k (0.1%) | 13 |
| Dead Time LG Falling to UG Rising | tDT2 | 65 | 80 | 95 | ns | CUG = CLG = OPEN, RDT = 10k (0.1%) | 13 |
| Dead Time UG Falling to LG Rising | tDT1 | 85 | 100 | 115 | ns | CUG = CLG = OPEN, RDT = 18.2kΩ (0.1%) | 13 |
| Dead Time LG Falling to UG Rising | tDT2 | 95 | 110 | 125 | ns | CUG = CLG = OPEN, RDT = 18.2kΩ (0.1%) | 13 |
| Dead Time UG Falling to LG Rising | tDT1 | 185 | 210 | 240 | ns | CUG = CLG = OPEN, RDT = 50kΩ (0.1%) | 13 |
| Dead Time LG Falling to UG Rising | tDT2 | 205 | 230 | 260 | ns | CUG = CLG = OPEN, RDT = 50kΩ (0.1%) | 13 |
| Dead Time UG Falling to LG Rising | tDT1 | 235 | 265 | 295 | ns | CUG = CLG = OPEN, RDT = 64.9kΩ (0.1%) | 13 |
| Dead Time LG Falling to UG Rising | tDT2 | 260 | 290 | 320 | ns | CUG = CLG = OPEN, RDT = 64.9kΩ (0.1%) | 13 |
| FB Overvoltage Rising Trip Threshold | VFBOV_RISE | 118 | 120 | 122 | % | Percentage of VDAC output reference (default VREF = 1.6V) | 13 |
| FB Overvoltage Falling Recovery Threshold | VFBOV_FALL | 114 | 116 | 118 | % | Percentage of VDAC output reference (default VREF = 1.6V) | 13 |
| Undervoltage Falling Trip Threshold | VFBUVREF_FALL | 78 | 80 | 82 | % | Percentage of VDAC output reference (default VREF = 1.6V) | 14 |
| Undervoltage Rising Recovery Threshold | VFBUVREF_RISE | 82.5 | 84 | 86.5 | % | Percentage of VDAC output reference (default VREF = 1.6V) | 14 |
| PGOOD Low Voltage | 0.06 | 0.4 | V | PGOOD LOW, IPGOOD = 0.5mA | 14 | ||
| NTC Output Sourcing Current | 19 | 20 | 21 | µA | EN >2V, pin voltage = 0V | 15 | |
| Operational Junction Temperature Range | TJ | -40 | 125 | °C | Automotive | 9 | |
| PVCC, VCC Operating Voltage | PVCC, VCC | 4.75 | 5.5 | V | 9 | ||
| VIN Absolute Maximum | VIN | -0.3 | 60 | V | 9 | ||
| Thermal Resistance Junction-Ambient | θJA | 28 | °C/W | 40 Ld 6x6 WFQFN, Notes 4, 5 | 9 | ||
| Thermal Resistance Junction-Case | θJC | 1.2 | °C/W | 40 Ld 6x6 WFQFN, Notes 4, 5 | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | SGND 11 Signal ground pin that the internal sensitive analog circuits refer to. Connect this pin to a large copper ground plane free | 4 |
CAD (KiCad official)
- Symbol:
ISL78229ARZ-T7A - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: TQFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
isl78229arz-t7a-etched.step/isl78229arz-t7a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl78229arz-t7a.step/isl78229arz-t7a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (72 pp, sha256
bf1d64560e236c82, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).