3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC6992CS6-2#TRMPBF
Analog Devices · Timers / Clock Oscillators · TSOT-23-6L
LTC6992CS6-2#TRMPBF from Analog Devices, in a TSOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MOD | input | Pulse-width modulation input whose linear control range is 0.1·VSET to 0.9·VSET (approximately 100mV to 900mV); beyond those limits the output clamps at 5% or 95%, or stops oscillating at 0% or 100% duty cycle, depending on the version. |
| 2 | GND | power_in | Ground; tie to a low inductance ground plane for best performance. |
| 3 | SET | input | Frequency-setting input regulated to 1V above GND, with ISET programmable from 1.25µA to 20µA; the output stops oscillating if ISET drops below approximately 500nA, and capacitance on this pin should be kept below 10pF (below 100pF maximum). |
| 4 | DIV | input | Programmable divider and polarity input whose voltage is converted to a 4-bit DIVCODE, where the MSB sets polarity (POL); use 1% resistors for accuracy and limit capacitance to less than 100pF. |
| 5 | V+ | power_in | Supply voltage input operating from 2.25V to 5.5V, which should be kept free from noise and ripple and bypassed directly to GND with a 0.1µF capacitor. |
| 6 | OUT | output | Oscillator output that swings from GND to V+ with an output resistance of approximately 30Ω; a series resistor should be used when driving an LED or other low-impedance load to limit source/sink current to 20mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6L |
| Category | RTC/Clock Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Frequency | fOUT | 3.81 | 1e+06 | Hz | 4 | ||
| Frequency Accuracy | ∆fOUT | -1.7 | 0.8 | 1.7 | % | 3.81Hz ≤ fOUT ≤ 1MHz | 4 |
| Frequency Drift Over Temperature | ∆fOUT/∆T | -0.005 | 0.005 | %/°C | 4 | ||
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.25 | 0.65 | %/V | V+ = 4.5V to 5.5V | 4 | |
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.08 | 0.18 | %/V | V+ = 2.25V to 4.5V | 4 | |
| PWM Duty Cycle Accuracy | ∆D | -3.7 | 3 | 3.7 | % | VMOD = 0.2 • VSET to 0.8 • VSET | 4 |
| PWM Duty Cycle Accuracy | ∆D | -4.9 | 4.5 | 4.9 | % | VMOD < 0.2 • VSET or VMOD > 0.8 • VSET | 4 |
| Maximum Duty Cycle Limit (LTC6992-2) | DMAX | 90.5 | 95 | 99 | % | LTC6992-2/LTC6992-3, POL = 0, VMOD = 1V | 4 |
| Minimum Duty Cycle Limit (LTC6992-2) | DMIN | 1 | 5 | 9.5 | % | LTC6992-2/LTC6992-4, POL = 0, VMOD = 0V | 4 |
| V+ Operating Supply Voltage Range | V+ | 2.25 | 5.5 | V | 4 | ||
| Supply Current | IS | 365 | 450 | µA | RL = ∞, RSET = 50k, NDIV = 1, V+ = 5.5V | 4 | |
| Supply Current | IS | 225 | 285 | µA | RL = ∞, RSET = 50k, NDIV = 1, V+ = 2.25V | 4 | |
| Supply Current | IS | 350 | 420 | µA | RL = ∞, RSET = 50k, NDIV = 4, V+ = 5.5V | 4 | |
| Supply Current | IS | 225 | 280 | µA | RL = ∞, RSET = 50k, NDIV = 4, V+ = 2.25V | 4 | |
| Supply Current | IS | 325 | 390 | µA | RL = ∞, RSET = 50k, NDIV ≥ 16, V+ = 5.5V | 4 | |
| Supply Current | IS | 215 | 265 | µA | RL = ∞, RSET = 50k, NDIV ≥ 16, V+ = 2.25V | 4 | |
| Supply Current | IS | 120 | 170 | µA | RL = ∞, RSET = 800k, NDIV = 1 to 16,384, V+ = 5.5V | 4 | |
| Supply Current | IS | 105 | 150 | µA | RL = ∞, RSET = 800k, NDIV = 1 to 16,384, V+ = 2.25V | 4 | |
| VSET Voltage at SET Pin | VSET | 0.97 | 1 | 1.03 | V | 5 | |
| VSET Drift Over Temperature | ∆VSET/∆T | -75 | 75 | µV/°C | 5 | ||
| Frequency-Setting Resistor | RSET | 50 | 800 | kΩ | 5 | ||
| MOD Pin Input Current | IMOD | -10 | 10 | nA | 5 | ||
| DIV Pin Valid Code Range Deviation | ∆VDIV/∆V+ | -1.5 | 1.5 | % | Deviation from Ideal VDIV/V+ = (DIVCODE + 0.5)/16 | 5 | |
| DIV Pin Input Current | IDIV | -10 | 10 | nA | 5 | ||
| Output Current | IOUT(MAX) | -20 | 20 | mA | V+ = 2.7V to 5.5V | 5 | |
| High Level Output Voltage | VOH | 5.45 | 5.48 | V | V+ = 5.5V, IOUT = -1mA | 5 | |
| High Level Output Voltage | VOH | 4.84 | 5.15 | V | V+ = 5.5V, IOUT = -16mA | 5 | |
| High Level Output Voltage | VOH | 3.24 | 3.27 | V | V+ = 3.3V, IOUT = -1mA | 5 | |
| High Level Output Voltage | VOH | 2.75 | 2.99 | V | V+ = 3.3V, IOUT = -10mA | 5 | |
| High Level Output Voltage | VOH | 2.17 | 2.21 | V | V+ = 2.25V, IOUT = -1mA | 5 | |
| High Level Output Voltage | VOH | 1.58 | 1.88 | V | V+ = 2.25V, IOUT = -8mA | 5 | |
| Low Level Output Voltage | VOL | 0.02 | 0.04 | V | V+ = 5.5V, IOUT = 1mA | 5 | |
| Low Level Output Voltage | VOL | 0.26 | 0.54 | V | V+ = 5.5V, IOUT = 16mA | 5 | |
| Low Level Output Voltage | VOL | 0.03 | 0.05 | V | V+ = 3.3V, IOUT = 1mA | 5 | |
| Low Level Output Voltage | VOL | 0.22 | 0.46 | V | V+ = 3.3V, IOUT = 10mA | 5 | |
| Low Level Output Voltage | VOL | 0.03 | 0.07 | V | V+ = 2.25V, IOUT = 1mA | 5 | |
| Supply Voltage (V+) to GND | V+ | 6 | V | Referenced to GND | 2 | ||
| Operating Temperature Range, LTC6992C | TOP | -40 | 85 | °C | LTC6992C (Note 2) | 2 | |
| Specified Temperature Range, LTC6992C | TSPEC | 0 | 70 | °C | LTC6992C (Note 3) | 2 | |
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Junction-to-Ambient Thermal Resistance, S6 Package | θJA | 192 | °C/W | S6 6-lead TSOT-23 package | 2 | ||
| Junction-to-Case Thermal Resistance, S6 Package | θJC | 51 | °C/W | S6 6-lead TSOT-23 package | 2 |
CAD (KiCad official)
- Symbol:
LTC6992CS6-2#TRMPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6L (KiCad packages3D, STEP)
- 3D model files:
ltc6992cs6-2-trmpbf-etched.step/ltc6992cs6-2-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6992cs6-2-trmpbf.step/ltc6992cs6-2-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (34 pp, sha256
a3a751f584fe2fcb, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).