3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMR14030QDPRRQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(4x4)
LMR14030QDPRRQ1 from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Bootstrap capacitor connection point for high-side MOSFET gate driver; connect high-quality 0.1μF capacitor between BOOT and SW pins. |
| 2 | VIN | power_in | Power supply input, operating voltage range 4V to 40V; connection to supply and bypass capacitor with shortest possible path to ground. |
| 3 | VIN | power_in | Power supply input, operating voltage range 4V to 40V; dual connection point to minimize supply path inductance. |
| 4 | EN | input | Enable control input with internal 1μA pull-up current source; pull below 1.2V threshold to disable device, above 1.2V to enable; under-voltage lockout can be adjusted with external resistor divider. |
| 5 | RT/SYNC | input | Frequency programming resistor to ground or external clock input; programs switching frequency 200kHz to 2.5MHz with resistor, or 250kHz to 2.3MHz with external clock; clock levels high ≥1.7V, low ≤0.5V, minimum pulse width ≥30ns. |
| 6 | SS | input | Soft-start capacitor connection point; charges at 3μA internal current to program soft-start time; maximum capacitor value 4.7nF for WSON package. |
| 7 | FB | input | Feedback voltage input from output divider to set VOUT; internal reference voltage 0.75V; do not allow short to ground during operation. |
| 8 | PGOOD | tri_state | Open-drain power good output flag indicating output voltage within regulation range (94-109% of VREF tolerance); requires 10kΩ to 100kΩ external pull-up resistor; maximum pin voltage 7V. |
| 9 | GND | power_in | System ground reference and return path for all circuits. |
| 10 | SW | output | Switching output node connected to internal low-side MOSFET and output power inductor; output voltage swings between ground and approximately VIN. |
| 11 | Thermal Pad | power_in | Primary thermal dissipation path for the die; must be connected to PCB ground plane to minimize junction-to-board thermal impedance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN to GND | -0.3 | 44 | V | 4 | |||
| BOOT to GND | -0.3 | 49 | V | 4 | |||
| SS to GND | -0.3 | 5 | V | 4 | |||
| FB to GND (DPR package) | -0.3 | 7 | V | 4 | |||
| RT/SYNC to GND | -0.3 | 3.6 | V | 4 | |||
| PGOOD to GND | -0.3 | 7 | V | 4 | |||
| BOOT to SW (DPR package) | 6.5 | V | 4 | ||||
| SW to GND | -3 | 44 | V | 4 | |||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VIN | 4 | 40 | V | 4 | |||
| VOUT | 0.8 | 28 | V | 4 | |||
| BOOT | 45 | V | 4 | ||||
| SW | -1 | 40 | V | 4 | |||
| FB | 0 | 5 | V | 4 | |||
| EN | 0 | 40 | V | 4 | |||
| RT/SYNC | 0 | 3.3 | V | 4 | |||
| SS | 0 | 3 | V | 4 | |||
| PGOOD to GND | 0 | 5 | V | 4 | |||
| Switching frequency range, RT mode | 200 | 2500 | kHz | 4 | |||
| Switching frequency range, SYNC mode | 250 | 2300 | kHz | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| VIN operating input voltage | VIN | 4 | 40 | V | 5 | ||
| UVLO rising threshold | 3.5 | 3.7 | 3.9 | V | 上升阈值 | 5 | |
| Shutdown supply current | ISHDN | 1 | 3 | μA | VEN = 0V, TJ = 25°C, 4.0V ≤ VIN ≤ 40V | 5 | |
| EN threshold voltage | VEN_TH | 1.05 | 1.2 | 1.38 | V | 5 | |
| PGOOD leakage current, high-level output | IPG | 10 | 200 | nA | VPull-Up = 5V | 5 | |
| PGOOD low-level output voltage | VPG_LOW | 0.1 | V | IPull-Up = 1mA | 5 | ||
| Minimum VIN for valid PGOOD output | VIN_PG_MIN | 1.6 | 1.95 | V | IPull-Up = 100μA 时,VPull-Up < 5V | 5 | |
| Feedback voltage | VFB | 0.744 | 0.75 | 0.756 | V | TJ = 25°C | 5 |
| Feedback voltage | VFB | 0.735 | 0.75 | 0.765 | V | TJ = -40°C to 125°C | 5 |
| High-side MOSFET on-resistance | RDS_ON | 90 | 180 | mΩ | VIN = 12V | 6 | |
| Current limit | ILIMT | 4.1 | 5.5 | 7.7 | A | VIN = 12V,TJ = -40°C 至 125°C,开环 | 6 |
| Switching frequency | fSW | 1758 | 1912 | 2066 | kHz | RT = 11.5kΩ | 6 |
| SYNC mode switching frequency range | 250 | 2300 | kHz | 6 | |||
| SYNC clock high voltage threshold | VSYNC_HI | 1.7 | V | 6 | |||
| SYNC clock low voltage threshold | VSYNC_LO | 0.5 | V | 6 | |||
| Minimum SYNC input pulse width | TSYNC_MIN | 30 | ns | 在 500kHz 时测得,VSYNC_HI > 3V,VSYNC_LO < 0.3V | 6 | ||
| UVLO hysteresis | 285 | mV | 5 | ||||
| Quiescent supply current (non-switching) | IQ | 40 | μA | VFB = 1.0V, TJ = 25°C | 5 | ||
| EN pin current at enable threshold +50mV | IEN_PIN | -4.6 | μA | 使能阈值 +50mV | 5 | ||
| EN pin current at enable threshold -50mV | IEN_PIN | -1 | μA | 使能阈值 -50mV | 5 | ||
| EN hysteresis current | IEN_HYS | -3.6 | μA | 5 | |||
| SS pin current | ISS | -3 | μA | TJ = 25°C | 5 | ||
| PGOOD undervoltage trip threshold (good) | VPG_UV | 94 | % | 电源正常(FB 电压百分比) | 5 | ||
| PGOOD undervoltage trip threshold (bad) | VPG_UV | 92 | % | 电源不良(FB 电压百分比) | 5 | ||
| PGOOD overvoltage trip threshold (bad) | VPG_OV | 109 | % | 电源不良(FB 电压百分比) | 5 | ||
| PGOOD overvoltage trip threshold (good) | VPG_OV | 107 | % | 电源正常(FB 电压百分比) | 5 | ||
| PGOOD recovery hysteresis | VPG_HYS | 2 | % | FB voltage % | 5 | ||
| Thermal shutdown threshold | TSHDN | 170 | °C | 6 | |||
| Thermal shutdown hysteresis | THYS | 12 | °C | 6 | |||
| PLL lock-in time | TLOCK_IN | 100 | µs | 在 500kHz 时测得 | 6 | ||
| Minimum controllable on-time | TON_MIN | 75 | ns | VIN = 12V,ILoad = 1A | 6 | ||
| Maximum duty cycle | DMAX | 97 | % | fSW = 200kHz | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 36.5 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 0.3 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 13.8 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 35.2 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 3.1 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 13.6 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
LMR14030QDPRRQ1 - Footprint:
Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm - 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lmr14030qdprrq1-etched.step/lmr14030qdprrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr14030qdprrq1.step/lmr14030qdprrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
1f91b09fa6ebdebe, retrieved 2026-10-03, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).