Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TC1304-VI0EMF

Microchip Tech · Linear Voltage Regulators (LDO) · DFN-10-EP(3x3)

TC1304-VI0EMF from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SHDN input Logic-level shutdown input that starts sequenced up/down of the LDO then the buck output; logic-high above 45% of VIN enables the outputs and logic-low below 15% of VIN turns them off.
2 VIN2 power_in LDO power input supply pin, connected to the variable input source and kept as short as possible from VIN1, with an optional extra capacitor to lower LDO input ripple.
3 VOUT2 power_out Regulated 300 mA LDO output that requires a 1 µF or larger capacitor to AGND for proper operation.
4 PG output Open-drain power-good output for the TC1304 that indicates the monitored output is within 94% of regulation, with a 300 ms delay for processor reset.
5 AGND power_in Analog ground connection that should be tied to the analog ground plane.
6 VFB/VOUT1 input Buck feedback input for the adjustable version (0.8 V to 4.5 V divider center) or buck output sense for the fixed-voltage versions.
7 AGND power_in Second analog ground pin on the TC1304 package (this pin is SHDN1 on the TC1303 variant).
8 VIN1 power_in Buck regulator power input supply pin, connected to a variable input source and kept short with traces to VIN2.
9 LX output Buck inductor connection that carries large switching current, so it must connect directly to the inductor with all connections kept as short as possible.
10 PGND power_in Power ground return for all large-signal currents, which should use a small loop area and length to limit switching-noise coupling.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage VIN 2.7 5.5 V Note 1, Note 2, Note 8 7
Maximum Output Current (buck) IOUT1_MAX 500 mA Note 1 7
Maximum Output Current (LDO) IOUT2_MAX 300 mA Note 1 7
Operating Current (TC1303C, TC1304) IQ 70.1 110 µA SHDN1 = SHDN2=VIN2, IOUT1 = 0 mA, IOUT2 = 0 mA 7
Shutdown Current, combined VIN1 and VIN2 IIN_SHDN 0.05 1 µA SHDN1 = SHDN2 = GND 7
SHDN Logic Input Voltage Low VIL 15 %VIN VIN1 =VIN2 = 2.7V to 5.5V 7
SHDN Logic Input Voltage High VIH 45 %VIN VIN1 =VIN2 = 2.7V to 5.5V 7
SHDN Input Leakage Current IIN -1 0.01 1 µA VIN1 =VIN2 = 2.7V to 5.5V, SHDNX = GND, SHDNY =VIN 7
Undervoltage Lockout (VOUT1 and VOUT2) UVLO 2.4 2.55 2.7 V VIN1 Falling 7
Adjustable Output Voltage Range VOUT1 0.8 4.5 V 8
Adjustable Reference Feedback Voltage VFB1 0.78 0.8 0.82 V 8
Output Voltage Tolerance Fixed (buck) VOUT1 -2.5 0.3 2.5 % Note 2 8
Internal Oscillator Frequency FOSC 1.6 2 2.4 MHz 8
LX Pin Leakage Current ILX -1 0.01 1 µA SHDN = 0V, VIN = 5.5V, LX = 0V, LX = 5.5V 8
Output Voltage Tolerance (LDO) VOUT2 -2.5 0.3 2.5 % Note 2 8
Line Regulation (LDO) ∆VOUT2/∆VIN -0.2 0.02 0.2 %/V (VR+1V) ≤ VIN ≤ 5.5V 8
Load Regulation, VOUT2 ≥ 2.5V ∆VOUT2/IOUT2 -0.75 -0.08 0.75 % IOUT2 = 0.1 mA to 300 mA (Note 4) 8
Load Regulation, VOUT2 < 2.5V ∆VOUT2/IOUT2 -0.9 -0.18 0.9 % IOUT2 = 0.1 mA to 300 mA (Note 4) 8
Dropout Voltage, VOUT2 > 2.5V VIN, VOUT2 137 205 mV IOUT2 = 200 mA (Note 5) 8
Power-Good Voltage Range VPG 1 5.5 V TA = 0°C to +70°C, VIN ≤ 2.7, ISINK = 100 µA 9
Power-Good Voltage Range VPG 1.2 5.5 V TA = -40°C to +85°C, VIN ≤ 2.7, ISINK = 100 µA 9
PG Threshold High (VOUT1 or VOUT2) VTH_H 94 96 % of VOUTX On Rising VOUT1 or VOUT2, VOUTX = VOUT1 or VOUT2 9
PG Threshold Low (VOUT1 or VOUT2) VTH_L 89 92 % of VOUTX On Falling VOUT1 or VOUT2, VOUTX = VOUT1 or VOUT2 9
Wake-Up Time (From SHDN2 mode), VOUT2 tWK 31 100 µs IOUT1 = IOUT2 = 50 mA 9
PG Active Time-out Period tRPU 140 262 560 ms VOUT1 or VOUT2 = VTH - 100 mV to VTH + 100 mV, ISINK = 1.2 mA 9
PG Output Voltage Low PG_VOL 0.2 V VOUT1 or VOUT2 = VTH - 100 mV, IPG = 1.2 mA, VIN2 > 2.7V; IPG = 100 µA, 1.0V < VIN2 < 2.7V 9
VIN - AGND (absolute maximum) 6 V 7
LX to PGND (absolute maximum) -0.3 V Upper limit printed as VIN + 0.3V (not a numeric value) 7
PGND to AGND (absolute maximum) -0.3 0.3 V 7
Ambient Temperature with Power Applied -40 85 °C 7
Operating Junction Temperature Range TJ -40 125 °C Steady state 10
Storage Temperature Range TA -65 150 °C 10
Maximum Junction Temperature TJ 150 °C Transient 10
Recommended input capacitor C(VIN1) C(VIN1) 4.7 µF Table 5-1 recommended capacitor values 25
Recommended buck output capacitor COUT1 COUT1 4.7 22 µF Table 5-1 recommended capacitor values 25
Recommended LDO output capacitor COUT2 COUT2 1 10 µF Table 5-1 recommended capacitor values 25
Recommended inductor DC resistance DCR 200 mΩ Recommended: less than 200 mΩ 26
Thermal Resistance, 10L-DFN θJA 41 °C/W Typical 4-layer Board with Internal Ground Plane and 2 Vias in Thermal Pad 10

CAD (KiCad official)

  • Symbol: TC1304-VI0EMF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tc1304-vi0emf-etched.step / tc1304-vi0emf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tc1304-vi0emf.step / tc1304-vi0emf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (38 pp, sha256 9ccb545ec9b0a8b1, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF