3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTC1304-VI0EMF
Microchip Tech · Linear Voltage Regulators (LDO) · DFN-10-EP(3x3)
TC1304-VI0EMF from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SHDN | input | Logic-level shutdown input that starts sequenced up/down of the LDO then the buck output; logic-high above 45% of VIN enables the outputs and logic-low below 15% of VIN turns them off. |
| 2 | VIN2 | power_in | LDO power input supply pin, connected to the variable input source and kept as short as possible from VIN1, with an optional extra capacitor to lower LDO input ripple. |
| 3 | VOUT2 | power_out | Regulated 300 mA LDO output that requires a 1 µF or larger capacitor to AGND for proper operation. |
| 4 | PG | output | Open-drain power-good output for the TC1304 that indicates the monitored output is within 94% of regulation, with a 300 ms delay for processor reset. |
| 5 | AGND | power_in | Analog ground connection that should be tied to the analog ground plane. |
| 6 | VFB/VOUT1 | input | Buck feedback input for the adjustable version (0.8 V to 4.5 V divider center) or buck output sense for the fixed-voltage versions. |
| 7 | AGND | power_in | Second analog ground pin on the TC1304 package (this pin is SHDN1 on the TC1303 variant). |
| 8 | VIN1 | power_in | Buck regulator power input supply pin, connected to a variable input source and kept short with traces to VIN2. |
| 9 | LX | output | Buck inductor connection that carries large switching current, so it must connect directly to the inductor with all connections kept as short as possible. |
| 10 | PGND | power_in | Power ground return for all large-signal currents, which should use a small loop area and length to limit switching-noise coupling. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 2.7 | 5.5 | V | Note 1, Note 2, Note 8 | 7 | |
| Maximum Output Current (buck) | IOUT1_MAX | 500 | mA | Note 1 | 7 | ||
| Maximum Output Current (LDO) | IOUT2_MAX | 300 | mA | Note 1 | 7 | ||
| Operating Current (TC1303C, TC1304) | IQ | 70.1 | 110 | µA | SHDN1 = SHDN2=VIN2, IOUT1 = 0 mA, IOUT2 = 0 mA | 7 | |
| Shutdown Current, combined VIN1 and VIN2 | IIN_SHDN | 0.05 | 1 | µA | SHDN1 = SHDN2 = GND | 7 | |
| SHDN Logic Input Voltage Low | VIL | 15 | %VIN | VIN1 =VIN2 = 2.7V to 5.5V | 7 | ||
| SHDN Logic Input Voltage High | VIH | 45 | %VIN | VIN1 =VIN2 = 2.7V to 5.5V | 7 | ||
| SHDN Input Leakage Current | IIN | -1 | 0.01 | 1 | µA | VIN1 =VIN2 = 2.7V to 5.5V, SHDNX = GND, SHDNY =VIN | 7 |
| Undervoltage Lockout (VOUT1 and VOUT2) | UVLO | 2.4 | 2.55 | 2.7 | V | VIN1 Falling | 7 |
| Adjustable Output Voltage Range | VOUT1 | 0.8 | 4.5 | V | 8 | ||
| Adjustable Reference Feedback Voltage | VFB1 | 0.78 | 0.8 | 0.82 | V | 8 | |
| Output Voltage Tolerance Fixed (buck) | VOUT1 | -2.5 | 0.3 | 2.5 | % | Note 2 | 8 |
| Internal Oscillator Frequency | FOSC | 1.6 | 2 | 2.4 | MHz | 8 | |
| LX Pin Leakage Current | ILX | -1 | 0.01 | 1 | µA | SHDN = 0V, VIN = 5.5V, LX = 0V, LX = 5.5V | 8 |
| Output Voltage Tolerance (LDO) | VOUT2 | -2.5 | 0.3 | 2.5 | % | Note 2 | 8 |
| Line Regulation (LDO) | ∆VOUT2/∆VIN | -0.2 | 0.02 | 0.2 | %/V | (VR+1V) ≤ VIN ≤ 5.5V | 8 |
| Load Regulation, VOUT2 ≥ 2.5V | ∆VOUT2/IOUT2 | -0.75 | -0.08 | 0.75 | % | IOUT2 = 0.1 mA to 300 mA (Note 4) | 8 |
| Load Regulation, VOUT2 < 2.5V | ∆VOUT2/IOUT2 | -0.9 | -0.18 | 0.9 | % | IOUT2 = 0.1 mA to 300 mA (Note 4) | 8 |
| Dropout Voltage, VOUT2 > 2.5V | VIN, VOUT2 | 137 | 205 | mV | IOUT2 = 200 mA (Note 5) | 8 | |
| Power-Good Voltage Range | VPG | 1 | 5.5 | V | TA = 0°C to +70°C, VIN ≤ 2.7, ISINK = 100 µA | 9 | |
| Power-Good Voltage Range | VPG | 1.2 | 5.5 | V | TA = -40°C to +85°C, VIN ≤ 2.7, ISINK = 100 µA | 9 | |
| PG Threshold High (VOUT1 or VOUT2) | VTH_H | 94 | 96 | % of VOUTX | On Rising VOUT1 or VOUT2, VOUTX = VOUT1 or VOUT2 | 9 | |
| PG Threshold Low (VOUT1 or VOUT2) | VTH_L | 89 | 92 | % of VOUTX | On Falling VOUT1 or VOUT2, VOUTX = VOUT1 or VOUT2 | 9 | |
| Wake-Up Time (From SHDN2 mode), VOUT2 | tWK | 31 | 100 | µs | IOUT1 = IOUT2 = 50 mA | 9 | |
| PG Active Time-out Period | tRPU | 140 | 262 | 560 | ms | VOUT1 or VOUT2 = VTH - 100 mV to VTH + 100 mV, ISINK = 1.2 mA | 9 |
| PG Output Voltage Low | PG_VOL | 0.2 | V | VOUT1 or VOUT2 = VTH - 100 mV, IPG = 1.2 mA, VIN2 > 2.7V; IPG = 100 µA, 1.0V < VIN2 < 2.7V | 9 | ||
| VIN - AGND (absolute maximum) | 6 | V | 7 | ||||
| LX to PGND (absolute maximum) | -0.3 | V | Upper limit printed as VIN + 0.3V (not a numeric value) | 7 | |||
| PGND to AGND (absolute maximum) | -0.3 | 0.3 | V | 7 | |||
| Ambient Temperature with Power Applied | -40 | 85 | °C | 7 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Steady state | 10 | |
| Storage Temperature Range | TA | -65 | 150 | °C | 10 | ||
| Maximum Junction Temperature | TJ | 150 | °C | Transient | 10 | ||
| Recommended input capacitor C(VIN1) | C(VIN1) | 4.7 | µF | Table 5-1 recommended capacitor values | 25 | ||
| Recommended buck output capacitor COUT1 | COUT1 | 4.7 | 22 | µF | Table 5-1 recommended capacitor values | 25 | |
| Recommended LDO output capacitor COUT2 | COUT2 | 1 | 10 | µF | Table 5-1 recommended capacitor values | 25 | |
| Recommended inductor DC resistance | DCR | 200 | mΩ | Recommended: less than 200 mΩ | 26 | ||
| Thermal Resistance, 10L-DFN | θJA | 41 | °C/W | Typical 4-layer Board with Internal Ground Plane and 2 Vias in Thermal Pad | 10 |
CAD (KiCad official)
- Symbol:
TC1304-VI0EMF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tc1304-vi0emf-etched.step/tc1304-vi0emf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tc1304-vi0emf.step/tc1304-vi0emf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (38 pp, sha256
9ccb545ec9b0a8b1, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).