Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TMUX7436FPWR

TI(德州仪器) · IC · TSSOP-16

TMUX7436FPWR from TI(德州仪器), in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SEL1 input Logic control input 1; together with EN, the SELx logic inputs determine individual switch states when EN is high, as provided in Table 8-1.
2 S1A bidirectional Overvoltage-protected source pin 1A, can be an input or output.
3 D1 bidirectional Drain pin 1, can be an input or output, and is not overvoltage protected.
4 S1B bidirectional Overvoltage-protected source pin 1B, can be an input or output.
5 VSS power_in Negative power supply, the most negative power-supply potential; may be tied to ground in single-supply use, with a 0.1 µF to 10 µF decoupling capacitor to GND.
6 GND power_in Ground (0 V) reference.
7 NC unconnected No internal connection; this pin can be shorted to GND or left floating.
8 DR input Drain Response input: tying DR to GND pulls the drain to VDD or VSS through a 40 kΩ resistor during an overvoltage fault, while a logic high or floating DR leaves the drain open circuit.
9 SEL2 input Logic control input 2; together with EN, the SELx logic inputs determine individual switch states when EN is high, as provided in Table 8-1.
10 S2A bidirectional Overvoltage-protected source pin 2A, can be an input or output.
11 D2 bidirectional Drain pin 2, can be an input or output, and is not overvoltage protected.
12 S2B bidirectional Overvoltage-protected source pin 2B, can be an input or output.
13 VDD power_in Positive power supply, the most positive power-supply potential; connect a 0.1 µF to 10 µF decoupling capacitor between VDD and GND.
14 EN input Active-high logic enable with an internal 4 MΩ pull-down; all switches become high impedance when EN is low.
15 FF output General fault flag, open-drain and asserted low when an overvoltage is detected on any source pin; connect to an external 1.8 V to 5.5 V supply through a 1 kΩ pull-up.
16 SF output Specific fault flag, open-drain and asserted low when an overvoltage is detected on a specific source pin selected by the SELx states per Table 8-1; connect to an external 1.8 V to 5.5 V supply through a 1 kΩ pull-up.

Key specifications

Parameter Value
Manufacturer TI(德州仪器)
Package TSSOP-16
Category
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD to VSS supply voltage 48 V over operating free-air temperature range 4
VDD to GND -0.3 48 V over operating free-air temperature range 4
VSS to GND -48 0.3 V over operating free-air temperature range 4
Source input pin (Sx) voltage to GND VS to GND -65 65 V over operating free-air temperature range 4
Source input pin (Sx) voltage to VDD VS to VDD -90 V over operating free-air temperature range 4
Source input pin (Sx) voltage to VSS VS to VSS 90 V over operating free-air temperature range 4
Logic control input pin voltage (EN, SELx, DR) VLOGIC 48 V printed minimum is GND -0.7 V; stresses at or below voltage and current ratings at all times 4
Logic output pin voltage (FF, SF) VxF 6 V printed minimum is GND -0.7 V 4
Logic control input pin current (EN, SELx, DR) ILOGIC -30 30 mA 4
Logic output pin current (FF, SF) IxF -10 10 mA 4
Storage temperature Tstg -65 150 °C 4
Ambient temperature TA -55 150 °C 4
Junction temperature TJ 150 °C 4
Total power dissipation (TSSOP) Ptot 650 mW TSSOP package; derates linearly above TA = 70°C by 10.1 mW/°C 4
Power supply voltage differential VDD, VSS 8 44 V 8 V ≤ (VDD, VSS) ≤ 44 V; minimum VDD must be met 5
Positive power supply voltage VDD 5 44 V 5
Source pin (Sx) voltage to GND (fault condition) VS to GND -60 60 V fault condition 5
Source pin (Sx) voltage to VDD or VD (fault condition) VS to VDD -85 V fault condition; may not exceed 85 V from supply pins or drain pins 5
Source pin (Sx) voltage to VSS or VD (fault condition) VS to VSS 85 V fault condition; may not exceed 85 V from supply pins or drain pins 5
Logic control input pin voltage (EN, SELx, DR) VLOGIC 44 V printed minimum is GND 5
Logic output pin voltage (FF, SF) VxF 5.5 V printed minimum is GND; FF is open drain 5
Ambient temperature TA -40 125 °C 5
Continuous current through switch, 1 channel, TSSOP IDC 115 mA operating 1 channel; TA = 25°C 5
Continuous current through switch, 1 channel, TSSOP IDC 85 mA operating 1 channel; TA = 125°C 5
Continuous current through switch, max channels at same time, TSSOP IDC 115 mA operating max number of channels; TA = 25°C 5
Continuous current through switch, max channels at same time, TSSOP IDC 60 mA operating max number of channels; TA = 125°C 5
Threshold voltage for fault detector VT 0.7 V 25°C 6
High-level input voltage VIH 1.3 44 V EN, SELx, DR pins; -40°C to +125°C 6
Low-level input voltage VIL 0 0.8 V EN, SELx, DR pins; -40°C to +125°C 6
Low-level output voltage VOL(FLAG) 0.35 V FF and SF pins, IO = 5 mA; -40°C to +125°C 6
Undervoltage lockout threshold voltage (VDD, VSS), rising edge VUVLO 5.1 5.8 6.6 V rising edge, single supply; -40°C to +125°C 6
Undervoltage lockout threshold voltage (VDD, VSS), falling edge VUVLO 5 5.7 6.4 V falling edge, single supply; -40°C to +125°C 6
VDD undervoltage lockout hysteresis VHYS 0.2 V single supply; -40°C to +125°C 6
Drain resistance to supply rail during overvoltage event on selected source pin RD(OVP) 40 kΩ 25°C 6
Electrostatic discharge, human body model (HBM) V(ESD) -4000 4000 V per ANSI/ESDA/JEDEC JS-001, all pins 4
Electrostatic discharge, charged device model (CDM) V(ESD) -750 750 V per ANSI/ESDA/JEDEC JS-002, all pins 4
Junction-to-ambient thermal resistance RθJA 100.4 °C/W PW (TSSOP) 16-pin package 5
Junction-to-case (top) thermal resistance RθJC(top) 31.3 °C/W PW (TSSOP) 16-pin package 5
Junction-to-board thermal resistance RθJB 46.4 °C/W PW (TSSOP) 16-pin package 5
Junction-to-top characterization parameter ΨJT 1.7 °C/W PW (TSSOP) 16-pin package 5
Junction-to-board characterization parameter ΨJB 45.8 °C/W PW (TSSOP) 16-pin package 5

CAD (KiCad official)

  • Symbol: TMUX7436FPWR
  • Footprint: Package_SO:TSSOP-16_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: tmux7436fpwr-etched.step / tmux7436fpwr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tmux7436fpwr.step / tmux7436fpwr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TI(德州仪器) datasheet (50 pp, sha256 8aea031e72a3f891, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF