Generated by kicad-footprint-generator · KiCad file format 20260206
TMUX7436FPWR
TI(德州仪器) · IC · TSSOP-16
TMUX7436FPWR from TI(德州仪器), in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SEL1 | input | Logic control input 1; together with EN, the SELx logic inputs determine individual switch states when EN is high, as provided in Table 8-1. |
| 2 | S1A | bidirectional | Overvoltage-protected source pin 1A, can be an input or output. |
| 3 | D1 | bidirectional | Drain pin 1, can be an input or output, and is not overvoltage protected. |
| 4 | S1B | bidirectional | Overvoltage-protected source pin 1B, can be an input or output. |
| 5 | VSS | power_in | Negative power supply, the most negative power-supply potential; may be tied to ground in single-supply use, with a 0.1 µF to 10 µF decoupling capacitor to GND. |
| 6 | GND | power_in | Ground (0 V) reference. |
| 7 | NC | unconnected | No internal connection; this pin can be shorted to GND or left floating. |
| 8 | DR | input | Drain Response input: tying DR to GND pulls the drain to VDD or VSS through a 40 kΩ resistor during an overvoltage fault, while a logic high or floating DR leaves the drain open circuit. |
| 9 | SEL2 | input | Logic control input 2; together with EN, the SELx logic inputs determine individual switch states when EN is high, as provided in Table 8-1. |
| 10 | S2A | bidirectional | Overvoltage-protected source pin 2A, can be an input or output. |
| 11 | D2 | bidirectional | Drain pin 2, can be an input or output, and is not overvoltage protected. |
| 12 | S2B | bidirectional | Overvoltage-protected source pin 2B, can be an input or output. |
| 13 | VDD | power_in | Positive power supply, the most positive power-supply potential; connect a 0.1 µF to 10 µF decoupling capacitor between VDD and GND. |
| 14 | EN | input | Active-high logic enable with an internal 4 MΩ pull-down; all switches become high impedance when EN is low. |
| 15 | FF | output | General fault flag, open-drain and asserted low when an overvoltage is detected on any source pin; connect to an external 1.8 V to 5.5 V supply through a 1 kΩ pull-up. |
| 16 | SF | output | Specific fault flag, open-drain and asserted low when an overvoltage is detected on a specific source pin selected by the SELx states per Table 8-1; connect to an external 1.8 V to 5.5 V supply through a 1 kΩ pull-up. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TI(德州仪器) |
| Package | TSSOP-16 |
| Category | |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD to VSS supply voltage | 48 | V | over operating free-air temperature range | 4 | |||
| VDD to GND | -0.3 | 48 | V | over operating free-air temperature range | 4 | ||
| VSS to GND | -48 | 0.3 | V | over operating free-air temperature range | 4 | ||
| Source input pin (Sx) voltage to GND | VS to GND | -65 | 65 | V | over operating free-air temperature range | 4 | |
| Source input pin (Sx) voltage to VDD | VS to VDD | -90 | V | over operating free-air temperature range | 4 | ||
| Source input pin (Sx) voltage to VSS | VS to VSS | 90 | V | over operating free-air temperature range | 4 | ||
| Logic control input pin voltage (EN, SELx, DR) | VLOGIC | 48 | V | printed minimum is GND -0.7 V; stresses at or below voltage and current ratings at all times | 4 | ||
| Logic output pin voltage (FF, SF) | VxF | 6 | V | printed minimum is GND -0.7 V | 4 | ||
| Logic control input pin current (EN, SELx, DR) | ILOGIC | -30 | 30 | mA | 4 | ||
| Logic output pin current (FF, SF) | IxF | -10 | 10 | mA | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Ambient temperature | TA | -55 | 150 | °C | 4 | ||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Total power dissipation (TSSOP) | Ptot | 650 | mW | TSSOP package; derates linearly above TA = 70°C by 10.1 mW/°C | 4 | ||
| Power supply voltage differential | VDD, VSS | 8 | 44 | V | 8 V ≤ (VDD, VSS) ≤ 44 V; minimum VDD must be met | 5 | |
| Positive power supply voltage | VDD | 5 | 44 | V | 5 | ||
| Source pin (Sx) voltage to GND (fault condition) | VS to GND | -60 | 60 | V | fault condition | 5 | |
| Source pin (Sx) voltage to VDD or VD (fault condition) | VS to VDD | -85 | V | fault condition; may not exceed 85 V from supply pins or drain pins | 5 | ||
| Source pin (Sx) voltage to VSS or VD (fault condition) | VS to VSS | 85 | V | fault condition; may not exceed 85 V from supply pins or drain pins | 5 | ||
| Logic control input pin voltage (EN, SELx, DR) | VLOGIC | 44 | V | printed minimum is GND | 5 | ||
| Logic output pin voltage (FF, SF) | VxF | 5.5 | V | printed minimum is GND; FF is open drain | 5 | ||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Continuous current through switch, 1 channel, TSSOP | IDC | 115 | mA | operating 1 channel; TA = 25°C | 5 | ||
| Continuous current through switch, 1 channel, TSSOP | IDC | 85 | mA | operating 1 channel; TA = 125°C | 5 | ||
| Continuous current through switch, max channels at same time, TSSOP | IDC | 115 | mA | operating max number of channels; TA = 25°C | 5 | ||
| Continuous current through switch, max channels at same time, TSSOP | IDC | 60 | mA | operating max number of channels; TA = 125°C | 5 | ||
| Threshold voltage for fault detector | VT | 0.7 | V | 25°C | 6 | ||
| High-level input voltage | VIH | 1.3 | 44 | V | EN, SELx, DR pins; -40°C to +125°C | 6 | |
| Low-level input voltage | VIL | 0 | 0.8 | V | EN, SELx, DR pins; -40°C to +125°C | 6 | |
| Low-level output voltage | VOL(FLAG) | 0.35 | V | FF and SF pins, IO = 5 mA; -40°C to +125°C | 6 | ||
| Undervoltage lockout threshold voltage (VDD, VSS), rising edge | VUVLO | 5.1 | 5.8 | 6.6 | V | rising edge, single supply; -40°C to +125°C | 6 |
| Undervoltage lockout threshold voltage (VDD, VSS), falling edge | VUVLO | 5 | 5.7 | 6.4 | V | falling edge, single supply; -40°C to +125°C | 6 |
| VDD undervoltage lockout hysteresis | VHYS | 0.2 | V | single supply; -40°C to +125°C | 6 | ||
| Drain resistance to supply rail during overvoltage event on selected source pin | RD(OVP) | 40 | kΩ | 25°C | 6 | ||
| Electrostatic discharge, human body model (HBM) | V(ESD) | -4000 | 4000 | V | per ANSI/ESDA/JEDEC JS-001, all pins | 4 | |
| Electrostatic discharge, charged device model (CDM) | V(ESD) | -750 | 750 | V | per ANSI/ESDA/JEDEC JS-002, all pins | 4 | |
| Junction-to-ambient thermal resistance | RθJA | 100.4 | °C/W | PW (TSSOP) 16-pin package | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 31.3 | °C/W | PW (TSSOP) 16-pin package | 5 | ||
| Junction-to-board thermal resistance | RθJB | 46.4 | °C/W | PW (TSSOP) 16-pin package | 5 | ||
| Junction-to-top characterization parameter | ΨJT | 1.7 | °C/W | PW (TSSOP) 16-pin package | 5 | ||
| Junction-to-board characterization parameter | ΨJB | 45.8 | °C/W | PW (TSSOP) 16-pin package | 5 |
CAD (KiCad official)
- Symbol:
TMUX7436FPWR - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
tmux7436fpwr-etched.step/tmux7436fpwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tmux7436fpwr.step/tmux7436fpwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TI(德州仪器) datasheet (50 pp, sha256
8aea031e72a3f891, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).