3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32G431KBU3
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-32(5x5)
STM32G431KBU3 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Standard operating voltage 1.71 V to 3.6 V; all VDD pins must be connected to the external supply within the permitted range. |
| 2 | PF0-OSC_IN | bidirectional | 5 V tolerant FT_fa I/O (Fm+ capable, analog switch supplied by VDDA) with alternate functions I2C2_SDA, SPI2_NSS/I2S2_WS, TIM1_CH3N and EVENTOUT, and additional functions ADC1_IN10 and OSC_IN (HSE oscillator input). |
| 3 | PF1-OSC_OUT | bidirectional | FT_a I/O (analog switch supplied by VDDA) with alternate functions SPI2_SCK/I2S2_CK and EVENTOUT, and additional functions ADC2_IN10, COMP3_INM and OSC_OUT (HSE oscillator output). |
| 4 | PG10-NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor (NRST); it also provides the MCO alternate function and EVENTOUT. |
| 5 | PA0 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM2_CH1, USART2_CTS, COMP1_OUT, TIM8_BKIN, TIM8_ETR, TIM2_ETR and EVENTOUT, and additional functions ADC12_IN1, COMP1_INM, COMP3_INP, RTC_TAMP2 and WKUP1. |
| 6 | PA1 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions RTC_REFIN, TIM2_CH2, USART2_RTS_DE, TIM15_CH1N and EVENTOUT, and additional functions ADC12_IN2, COMP1_INP, OPAMP1_VINP and OPAMP3_VINP. |
| 7 | PA2 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM2_CH3, USART2_TX, COMP2_OUT, TIM15_CH1, LPUART1_TX, UCPD1_FRSTX and EVENTOUT, and additional functions ADC1_IN3, COMP2_INM, OPAMP1_VOUT and WKUP4/LSCO. |
| 8 | PA3 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM2_CH4, SAI1_CK1, USART2_RX, TIM15_CH2, LPUART1_RX, SAI1_MCLK_A and EVENTOUT, and additional functions ADC1_IN4, COMP2_INP and OPAMP1_VINM/OPAMP1_VINP. |
| 9 | PA4 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM3_CH2, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK, SAI1_FS_B and EVENTOUT, and additional functions ADC2_IN17, DAC1_OUT1 and COMP1_INM. |
| 10 | PA5 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM2_CH1, TIM2_ETR, SPI1_SCK, UCPD1_FRSTX and EVENTOUT, and additional functions ADC2_IN13, DAC1_OUT2, COMP2_INM and OPAMP2_VINM. |
| 11 | PA6 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM16_CH1, TIM3_CH1, TIM8_BKIN, SPI1_MISO, TIM1_BKIN, COMP1_OUT, LPUART1_CTS and EVENTOUT, and additional functions ADC2_IN3 and OPAMP2_VOUT. |
| 12 | PA7 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM17_CH1, TIM3_CH2, TIM8_CH1N, SPI1_MOSI, TIM1_CH1N, COMP2_OUT, UCPD1_FRSTX and EVENTOUT, and additional functions ADC2_IN4, COMP2_INP, OPAMP1_VINP and OPAMP2_VINP. |
| 13 | PB0 | bidirectional | 3.6 V tolerant TT_a I/O (analog switch supplied by VDDA) with alternate functions TIM3_CH3, TIM8_CH2N, TIM1_CH2N, UCPD1_FRSTX and EVENTOUT, and additional functions ADC1_IN15, COMP4_INP, OPAMP2_VINP and OPAMP3_VINP. |
| 14 | VSSA | power_in | Analog ground pin for the ADC, DAC, OPAMP, COMP and VREFBUF blocks; all ground pins must be kept within 50 mV of VSS. |
| 15 | VDDA/VREF+ | power_in | Analog supply pin shared with the VREF+ reference input on this package (VREFBUF_OUT as the alternate option); VDDA is 1.62 V to 3.6 V for ADC or COMP use, 1.71 V to 3.6 V for DAC 1 MSPS or 15 MSPS use, and VREF+ must not exceed VDDA by more than 0.4 V. |
| 16 | VSS | power_in | Ground pin; all VSS pins must be connected to the external ground within the permitted range. |
| 17 | VDD | power_in | Standard operating voltage 1.71 V to 3.6 V; all VDD pins must be connected to the external supply within the permitted range. |
| 18 | PA8 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) with alternate functions MCO, I2C3_SCL, I2C2_SDA, I2S2_MCK, TIM1_CH1, USART1_CK, TIM4_ETR, SAI1_CK2, SAI1_SCK_A and EVENTOUT. |
| 19 | PA9 | bidirectional | 5 V tolerant FT_fd I/O (Fm+ capable, USB Type-C dead battery function) with alternate functions I2C3_SMBA, I2C2_SCL, I2S3_MCK, TIM1_CH2, USART1_TX, TIM15_BKIN, TIM2_CH3, SAI1_FS_A and EVENTOUT, and additional function UCPD1_DBCC1. |
| 20 | PA10 | bidirectional | 5 V tolerant FT_da I/O (USB Type-C dead battery function) with alternate functions TIM17_BKIN, USB_CRS_SYNC, I2C2_SMBA, SPI2_MISO, TIM1_CH3, USART1_RX, TIM2_CH4, TIM8_BKIN, SAI1_D1, SAI1_SD_A and EVENTOUT, and additional function UCPD1_DBCC2. |
| 21 | PA11 | bidirectional | 5 V tolerant FT_u I/O with USB function, alternate functions SPI2_MOSI/I2S2_SD, TIM1_CH1N, USART1_CTS, COMP1_OUT, FDCAN1_RX, TIM4_CH1, TIM1_CH4, TIM1_BKIN2 and EVENTOUT, and additional function USB_DM. |
| 22 | PA12 | bidirectional | 5 V tolerant FT_u I/O with USB function, alternate functions TIM16_CH1, I2SCKIN, TIM1_CH2N, USART1_RTS_DE, COMP2_OUT, FDCAN1_TX, TIM4_CH2, TIM1_ETR and EVENTOUT, and additional function USB_DP. |
| 23 | PA13 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) that after reset is the SWDIO-JTMS debug alternate function with an internal pull-up enabled; other alternate functions are TIM16_CH1N, I2C1_SCL, IR_OUT, USART3_CTS, TIM4_CH3, SAI1_SD_B and EVENTOUT. |
| 24 | PA14 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) that after reset is the SWCLK-JTCK debug alternate function with an internal pull-down enabled; other alternate functions are LPTIM1_OUT, I2C1_SDA, TIM8_CH2, TIM1_BKIN, USART2_TX, SAI1_FS_B and EVENTOUT. |
| 25 | PA15 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) that after reset is the JTDI debug alternate function with an internal pull-up enabled; other alternate functions are TIM2_CH1, TIM8_CH1, I2C1_SCL, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_RX, UART4_RTS_DE, TIM1_BKIN, TIM2_ETR and EVENTOUT. |
| 26 | PB3 | bidirectional | 5 V tolerant FT I/O that after reset is the JTDO-TRACESWO debug alternate function; other alternate functions are TIM2_CH2, TIM4_ETR, USB_CRS_SYNC, TIM8_CH1N, SPI1_SCK, SPI3_SCK/I2S3_CK, USART2_TX, TIM3_ETR, SAI1_SCK_B and EVENTOUT. |
| 27 | PB4 | bidirectional | 5 V tolerant FT_c I/O (USB Type-C PD capable) that after reset is the JTRST debug alternate function with an internal pull-up enabled and a UCPD pull-down (Rd 5.1 kΩ) that can be disabled through UCPD1_DBDIS; other alternate functions are TIM16_CH1, TIM3_CH1, TIM8_CH2N, SPI1_MISO, SPI3_MISO, USART2_RX, TIM17_BKIN, SAI1_MCLK_B, EVENTOUT and additional function UCPD1_CC2. |
| 28 | PB5 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) with alternate functions TIM16_BKIN, TIM3_CH2, TIM8_CH3N, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI/I2S3_SD, USART2_CK, I2C3_SDA, TIM17_CH1, LPTIM1_IN1, SAI1_SD_B and EVENTOUT. |
| 29 | PB6 | bidirectional | 5 V tolerant FT_c I/O (USB Type-C PD capable) with alternate functions TIM16_CH1N, TIM4_CH1, TIM8_CH1, TIM8_ETR, USART1_TX, COMP4_OUT, TIM8_BKIN2, LPTIM1_ETR, SAI1_FS_B and EVENTOUT, and additional function UCPD1_CC1 with a 5.1 kΩ pull-down that is enabled after reset as controlled by PA9. |
| 30 | PB7 | bidirectional | 5 V tolerant FT_f I/O (Fm+ capable) with alternate functions TIM17_CH1N, TIM4_CH2, I2C1_SDA, TIM8_BKIN, USART1_RX, COMP3_OUT, TIM3_CH4, LPTIM1_IN2, UART4_CTS and EVENTOUT, and additional function PVD_IN. |
| 31 | PB8-BOOT0 | input | Dedicated BOOT0 pin, 5 V tolerant FT_f I/O (Fm+ capable) that also provides TIM16_CH1, TIM4_CH3, SAI1_CK1, I2C1_SCL, USART3_RX, COMP1_OUT, FDCAN1_RX, TIM8_CH2, TIM1_BKIN, SAI1_MCLK_A and EVENTOUT; it is recommended to set PB8 out of analog mode after startup to limit consumption if left unconnected. |
| 32 | VSS | power_in | Ground pin; all VSS pins must be connected to the external ground within the permitted range. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VBAT, VREF+) | VDD - VSS | -0.3 | 4 | V | 69 | ||
| Input voltage on FT_xxx pins except FT_c | VIN | -0.3 | V | Min is VSS-0.3; max printed as min(VDD, VDDA)+4.0 V (footnotes 3, 4), not a number | 69 | ||
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | Min is VSS-0.3 | 69 | |
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | Min is VSS-0.3 | 69 | |
| Input voltage on any other pins | VIN | -0.3 | 4 | V | Min is VSS-0.3 | 69 | |
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 69 | |||
| Variations between all the different ground pins (includes VREF-) | /VSSx-VSS/ | 50 | mV | 69 | |||
| Allowed voltage difference for VREF+ > VDDA | VREF+-VDDA | 0.4 | V | 69 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 150 | mA | 70 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 150 | mA | 70 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 70 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 70 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 70 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 70 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 70 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 70 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 70 | |||
| Injected current on FT_xxx, TT_xx, NRST pins | IINJ(PIN) | -5 | 0 | mA | 70 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 70 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 70 | ||
| Maximum junction temperature | TJ | 150 | °C | 70 | |||
| Internal AHB clock frequency | fHCLK | 0 | 170 | MHz | 71 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 170 | MHz | 71 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 170 | MHz | 71 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 71 | ||
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 71 | |
| Analog supply voltage | VDDA | 1.71 | 3.6 | V | DAC 1 MSPS or DAC 15 MSPS | 71 | |
| Analog supply voltage | VDDA | 2 | 3.6 | V | OPAMP used | 71 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 71 | |
| Analog supply voltage | VDDA | 0 | 3.6 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 71 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 71 | ||
| I/O input voltage on TT_xx I/O | VIN | -0.3 | V | Max printed as VDD+0.3 V, not a number | 71 | ||
| I/O input voltage on FT_c I/O | VIN | -0.3 | 5 | V | 71 | ||
| I/O input voltage on all I/O except TT_xx and FT_c | VIN | -0.3 | V | Max printed as MIN(MIN(VDD, VDDA)+3.6 V, 5.5 V), not a number | 71 | ||
| Ambient temperature, maximum power dissipation | TA | -40 | 125 | °C | Suffix 3 version | 71 | |
| Ambient temperature, low-power dissipation | TA | -40 | 130 | °C | Suffix 3 version | 71 | |
| Junction temperature range | TJ | -40 | 130 | °C | Suffix 3 version | 71 | |
| VDD rise time rate | tVDD | 0 | µs/V | Max printed as ∞, not a number | 72 | ||
| VDD fall time rate | tVDD | 10 | µs/V | Max printed as ∞, not a number | 72 | ||
| VDDA rise time rate | tVDDA | 0 | µs/V | Max printed as ∞, not a number | 72 | ||
| VDDA fall time rate | tVDDA | 10 | µs/V | Max printed as ∞, not a number | 72 | ||
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | μs | VDD rising | 72 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 72 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 72 |
| Brown-out reset threshold 1, rising edge | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 72 |
| Brown-out reset threshold 1, falling edge | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 72 |
| Brown-out reset threshold 2, rising edge | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 72 |
| Brown-out reset threshold 2, falling edge | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 72 |
| Brown-out reset threshold 3, rising edge | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 72 |
| Brown-out reset threshold 3, falling edge | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 72 |
| Brown-out reset threshold 4, rising edge | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 72 |
| Brown-out reset threshold 4, falling edge | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 72 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 74 |
| Start time of reference voltage buffer | tstart_vrefint | 8 | 12 | µs | when ADC is enabled | 74 | |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 74 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 74 |
CAD (KiCad official)
- Symbol:
STM32G431KBU3 - Footprint:
Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm - 3D model: UFQFPN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
stm32g431kbu3-etched.step/stm32g431kbu3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32g431kbu3.step/stm32g431kbu3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (197 pp, sha256
caaa126a00ab9e06, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).