3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownINA209AIPWR
Texas Instruments · Current Sense Amplifiers · TSSOP-16
INA209AIPWR from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN+ | power_in | Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range ±40mV to ±320mV depending on PGA gain setting; common-mode range 0V to 26V. |
| 2 | VIN- | power_in | Negative differential shunt voltage input; connect to negative side of shunt resistor; bus voltage measured from this pin to ground; common-mode range 0V to 26V. |
| 3 | Convert | input | Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4µs to initiate conversion; tie high if unused. |
| 4 | GND | power_in | Ground connection; must be connected together with pin 11 to system ground. |
| 5 | VS+ | power_in | Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 10. |
| 6 | GPIO | bidirectional | General-purpose input/output with totem-pole output topology; user-programmable via Critical DAC+ register; default state is high-impedance input; can be configured as output 0, output 1, or Hi-Z. |
| 7 | Critical | tri_state | Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5µs of overload condition detection. |
| 8 | Overlimit | tri_state | Open-drain over-limit watchdog output; active-low; transparent (non-latched) by default; responds to over-limit comparator thresholds for bus voltage and power limits. |
| 9 | Warning | tri_state | Open-drain warning watchdog output; active-low; transparent (non-latched) by default; responds to warning comparator thresholds with programmable delay 0 to 1.5s. |
| 10 | VS+ | power_in | Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 5. |
| 11 | GND | power_in | Ground connection; must be connected together with pin 4 to system ground. |
| 12 | SCL | bidirectional | I²C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout. |
| 13 | SDA | bidirectional | I²C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout. |
| 14 | A0 | input | Address input pin; sets slave address bits A0 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND. |
| 15 | A1 | input | Address input pin; sets slave address bits A1 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND. |
| 16 | SMBus Alert | tri_state | Open-drain SMBus alert output; active-low; responds to warning, over-limit, critical faults, or conversion ready states; latched and cleared by status register read or alert response; controlled via SMBus Alert Mask/Enable Control Register. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Amplifiers/Comparators |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VS | 6 | V | 2 | |||
| Differential input voltage (VIN+) - (VIN-) | -26 | 26 | V | 2 | |||
| Analog inputs VIN+, VIN- common-mode | -0.3 | 26 | V | 2 | |||
| Open-drain digital outputs | -0.3 | 6 | V | referenced to GND | 2 | ||
| GPIO, Convert pins | -0.3 | V | referenced to GND; max printed as VS + 0.3 V | 2 | |||
| Input current into any pin | 5 | mA | 2 | ||||
| Open-drain digital output current | 10 | mA | 2 | ||||
| Operating temperature | -40 | 125 | °C | over operating free-air temperature range | 2 | ||
| Storage temperature | -65 | 150 | °C | 2 | |||
| Junction temperature | 150 | °C | 2 | ||||
| ESD rating Human Body Model | 2000 | V | 2 | ||||
| ESD rating Charged-Device Model | 1000 | V | 2 | ||||
| ESD rating Machine Model | 150 | V | 2 | ||||
| Full-scale current sense (input) voltage range | 0 | 40 | mV | PGA = ÷ 1 | 3 | ||
| Full-scale current sense (input) voltage range | 0 | 80 | mV | PGA = ÷ 2 | 3 | ||
| Full-scale current sense (input) voltage range | 0 | 160 | mV | PGA = ÷ 4 | 3 | ||
| Full-scale current sense (input) voltage range | 0 | 320 | mV | PGA = ÷ 8 | 3 | ||
| Bus voltage (input voltage) range | 0 | 32 | V | BRNG = 1 | 3 | ||
| Bus voltage (input voltage) range | 0 | 16 | V | BRNG = 0 | 3 | ||
| Common-mode rejection ratio CMRR | CMRR | 100 | 120 | dB | VIN+ = 0V to 26V | 3 | |
| Offset voltage, RTI | VOS | -100 | 10 | 100 | µV | PGA = ÷ 1; typ printed ±10 | 3 |
| Offset voltage, RTI | VOS | -125 | 20 | 125 | µV | PGA = ÷ 2; typ printed ±20 | 3 |
| Offset voltage, RTI | VOS | -150 | 30 | 150 | µV | PGA = ÷ 4; typ printed ±30 | 3 |
| Offset voltage, RTI | VOS | -200 | 40 | 200 | µV | PGA = ÷ 8; typ printed ±40 | 3 |
| Current sense gain error | -40 | 40 | m% | 3 | |||
| Input leakage VIN+ pin | -0.5 | 0.1 | 0.5 | µA | Power-Down Mode | 3 | |
| Input leakage VIN- pin | -0.5 | 0.1 | 0.5 | µA | Power-Down Mode | 3 | |
| Current measurement error | -0.5 | 0.2 | 0.5 | % | 3 | ||
| Current measurement error | -1 | 1 | % | over Temperature | 3 | ||
| Bus voltage measurement error | -0.5 | 0.2 | 0.5 | % | 3 | ||
| Bus voltage measurement error | -1 | 1 | % | over Temperature | 3 | ||
| Critical DAC accuracy | -1 | 0.5 | 1 | % | 3 | ||
| Critical DAC comparator offset | -1.6 | 0.3 | 1.6 | mV | 3 | ||
| ADC conversion time 12-bit | 532 | 586 | µs | 4 | |||
| ADC conversion time 11-bit | 276 | 304 | µs | 4 | |||
| ADC conversion time 10-bit | 148 | 163 | µs | 4 | |||
| ADC conversion time 9-bit | 84 | 93 | µs | 4 | |||
| Minimum convert input low time | 4 | µs | 4 | ||||
| SMBus timeout | 28 | 35 | ms | resets interface when SCL or SDA low for over 28 ms | 4 | ||
| Input logic level high | VIH | 6 | V | min printed as 0.7 (VS) | 4 | ||
| Input logic level low | VIL | -0.3 | V | max printed as 0.3 (VS) | 4 | ||
| GPIO pin output low | 0.15 | 0.4 | V | ISINK = 3mA | 4 | ||
| Open-drain logic '0' output level | 0.15 | 0.4 | V | ISINK = 3mA | 4 | ||
| High-level output leakage current | 0.1 | 1 | µA | VOUT = VS | 4 | ||
| Leakage input current | 0.1 | 1 | µA | 0 ≤ VIN ≤ VS | 4 | ||
| Operating supply range | VS | 3 | 5.5 | V | 4 | ||
| Quiescent current | IQ | 1 | 1.5 | mA | 4 | ||
| Quiescent current, power-down mode | IQ | 6 | 15 | µA | power-down mode | 4 | |
| Specified temperature range | -25 | 85 | °C | boldface limits apply over this range | 4 | ||
| Operating temperature range | -40 | 125 | °C | 4 | |||
| Thermal resistance junction-to-ambient TSSOP-16 | θJA | 150 | °C/W | TSSOP-16 | 4 |
CAD (KiCad official)
- Symbol:
INA209AIPWR - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
ina209aipwr-etched.step/ina209aipwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ina209aipwr.step/ina209aipwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (50 pp, sha256
fc088bc8d26a494f, retrieved 2026-09-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).