3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM75AD-TUDI
Tudi · Temperature Sensors · SOP-8
LM75AD-TUDI from Tudi, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Digital I/O, I2C bus bidirectional data line with open-drain output; needs an external pull-up (about 10 kΩ) and must not float. |
| 2 | SCL | input | Digital input for the I2C bus clock; needs an external pull-up (about 10 kΩ) and must not float. |
| 3 | OS | output | Overtemperature shutdown/interrupt open-drain output with programmable polarity, needing an external pull-up resistor of up to 200 kΩ. |
| 4 | GND | power_in | Ground, connected to the system ground. |
| 5 | A2 | input | Digital input where the user configures I2C address bit 2 (tie to GND or VCC, do not float). |
| 6 | A1 | input | Digital input where the user configures I2C address bit 1 (tie to GND or VCC, do not float). |
| 7 | A0 | input | Digital input where the user configures I2C address bit 0 (tie to GND or VCC, do not float). |
| 8 | VCC | power_in | Power supply input, 2.8 V to 5.5 V, with a decoupling capacitor recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Tudi |
| Package | SOP-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.8 | 5.5 | V | Recommended working conditions | 18 | |
| Operating ambient temperature range | Tamb | -55 | 125 | °C | 2 | ||
| Temperature accuracy | -0.5 | 0.5 | °C | 0°C to +50°C | 2 | ||
| Temperature accuracy | -1 | 1 | °C | -25°C to +100°C | 2 | ||
| I2C bus frequency range (lower limit) | 20 | Hz | I2C bus clock | 2 | |||
| I2C bus frequency range (upper limit) | 400 | kHz | I2C bus clock | 2 | |||
| OS pull-up resistor | 200 | kΩ | OS open-drain output; resistor as large as possible | 11 | |||
| Bus error timeout | tto | 75 | ms | SDA held low | 6 | ||
| ESD protection, HBM | 4500 | V | JESD22-A114 | 2 | |||
| ESD protection, CDM | 1000 | V | JESD22-C101 | 2 | |||
| Latch-up test current | 100 | mA | Latch test per JESD78 | 2 | |||
| SCL/SDA input hysteresis voltage | 500 | mV | SCL and SDA input thresholds | 17 | |||
| POR-related low-voltage duration | 2 | µs | VCC below POR level (about 1.0 V) for longer than this time before reset | 13 | |||
| Shutdown (sleep mode) supply current | 0.1 | µA | Sleep mode | 13 | |||
| Power-on reset threshold voltage | POR | 1 | V | VCC drops below this level | 13 | ||
| Temperature conversion time | tconv(T) | 10 | ms | Normal mode | 3 | ||
| Temperature conversion cycle | Tconv | 100 | ms | Normal mode, one conversion every cycle | 3 | ||
| Temperature resolution (11-bit) | 0.125 | °C | Temperature register | 2 | |||
| Setpoint resolution (Tos, Thyst) | 0.5 | °C | 9-bit Tos and Thyst registers | 11 | |||
| Default overtemperature threshold | Tth(ots) | 80 | °C | Power-on default | 4 | ||
| Default hysteresis temperature | Thyst | 75 | °C | Power-on default | 4 | ||
| Breakdown voltage, address/OS pins | 11 | V | ESD latch-based breakdown, typical | 17 | |||
| Breakdown voltage, SCL/SDA pins | 9.5 | V | ESD latch-based breakdown, typical | 17 | |||
| I2C pull-up resistor (external, SCL and SDA) | 10 | kΩ | Required when bus pull-up is not installed | 6 |
CAD (KiCad official)
- Symbol:
LM75AD-TUDI - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
lm75ad-tudi-etched.step/lm75ad-tudi-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm75ad-tudi.step/lm75ad-tudi.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Tudi datasheet (25 pp, sha256
a48faa5d824b6153, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).