Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM9076S-3.3

Texas Instruments · Linear Voltage Regulators (LDO) · TO-263-5

LM9076S-3.3 from Texas Instruments, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Unregulated supply input, operating range 5.35V to 40V (absolute maximum -15V to +55V), needing a 10 µF capacitor plus at least a 0.1 µF ceramic close to the pin.
2 VOUT power_out Regulated 3.3V output rated for 150 mA, requiring a minimum 10 µF output capacitor with 0.5Ω to 4.0Ω ESR for stability.
3 GROUND power_in Ground pin, with the package tab also connected to ground.
4 /RESET output Active-low open-collector delayed reset output that needs an external pull-up resistor of 10 kΩ to 200 kΩ, with an absolute maximum of -0.3V to 20V.
5 CDELAY passive Reset delay timing capacitor pin, charged at a typical 0.42 µA to set tDELAY = VOUT x (CDELAY/IDELAY), with an absolute maximum of -0.3V to VOUT+0.3V.
6 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TO-263-5
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output voltage (LM9076-3.3, -20°C to 85°C) VOUT 3.251 3.3 3.349 V −20°C ≤ TJ ≤ 85°C 3
Output voltage (LM9076-3.3, 1 mA to 150 mA) VOUT 3.234 3.3 3.366 V 1 mA ≤ ILOAD ≤ 150 mA 3
Output voltage (LM9076-3.3, 1 mA to 150 mA, full range) VOUT 3.201 3.3 3.399 V 1mA ≤ ILOAD ≤ 150 mA 3
Output voltage (LM9076-3.3, transient) VOUT 2.97 3.3 3.63 V VIN = 60V, RLOAD = 1 kΩ, t ≤ 40ms 3
Output Voltage Off (reverse battery) -300 0 mV VIN = -15V, Reverse Battery, RLOAD = 1 kΩ 3
Line regulation (9.0V to 16V) ΔVOUT 4 25 mV 9.0V ≤ VIN ≤ 16V, ILOAD = 10 mA 3
Line regulation (16V to 40V) ΔVOUT 17 35 mV 16V ≤ VIN ≤ 40V, ILOAD = 10 mA 3
Load regulation ΔVOUT 42 60 mV 1 mA ≤ ILOAD ≤ 150 mA 3
Dropout voltage (10 mA) VDO 30 50 mV ILOAD = 10 mA 3
Dropout voltage (150 mA) VDO 150 250 mV ILOAD = 150 mA 3
Ground pin current (100 uA load) IGND 25 45 μA 9V ≤ VIN ≤ 16V, ILOAD = 100 uA 3
Ground pin current (10 mA load) IGND 125 160 μA 9V ≤ VIN ≤ 40V, ILOAD = 10 mA 3
Ground pin current (150 mA load) IGND 3.6 4.5 mA 9V ≤ VIN ≤ 16V, ILOAD = 150 mA 3
VOUT short circuit current ISC 200 400 750 mA VIN = 14V, RLOAD = 1Ω 3
Ripple rejection PSRR 50 60 dB VIN = (14VDC) + (1VRMS @ 120Hz), ILOAD = 50 mA 3
Minimum VIN for valid RESET status VOR 1.3 2 V (Note 3) 3
VOUT threshold for RESET low (nom) VTHR 0.83 0.89 0.94 x VOUT (Note 3) 3
RESET pin low voltage VOL 0.2 0.3 V CDELAY < 4.0V, ISINK = 250 µA 3
CDELAY charging current IDELAY -0.7 -0.42 -0.25 uA VIN = 14V, VDELAY = 0V 4
Reset delay time tDELAY 4.7 7.8 13.2 ms VIN = 14V, CDELAY = 0.001 uF; VOUT rising from 0V, Δt from VOUT > VOR to RESET pin HIGH 4
Minimum input voltage DC (absolute maximum) VIN(DC) -15 55 V 2
Positive transient input voltage VIN(+Transient) 70 V t < 10ms, Duty Cycle <1% 2
Negative transient input voltage VIN(-Transient) -50 V t < 1ms, Duty Cycle <1% 2
RESET pin voltage -0.3 20 V 2
CDELAY pin voltage (lower limit) -0.3 V upper limit printed as VOUT +0.3V 2
Storage temperature -65 150 °C 2
Junction temperature (absolute maximum) TJ 175 C 2
ESD HBM -2 2 kV per AEC-Q100-002 2
ESD MM -250 250 V per AEC-Q100-003 2
VIN pin operating range VIN 5.35 40 V 2
Junction temperature operating range TJ -40 125 °C 2
Thermal resistance junction-to-ambient (KTT0005B) θJA 75 °C/W KTT0005B; worst case free air per EIA/JESD51-3 (Note 3) 2
Thermal resistance junction-to-case (KTT0005B) θJC 2.9 °C/W KTT0005B; Note 3 2

CAD (KiCad official)

  • Symbol: LM9076S-3.3
  • Footprint: Package_TO_SOT_SMD:TO-263-5_TabPin6
  • 3D model: TO-263-5 (KiCad packages3D, STEP)
  • 3D model files: lm9076s-3-3-etched.step / lm9076s-3-3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm9076s-3-3.step / lm9076s-3-3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (23 pp, sha256 41d0546b0bedab53, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF