component
LM9076S-3.3
Public Made by Adomby adom
Texas Instruments Linear Voltage Regulators (LDO), TO-263-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
LM9076S-3.3
Texas Instruments · Linear Voltage Regulators (LDO) · TO-263-5
LM9076S-3.3 from Texas Instruments, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Unregulated supply input, operating range 5.35V to 40V (absolute maximum -15V to +55V), needing a 10 µF capacitor plus at least a 0.1 µF ceramic close to the pin. |
| 2 | VOUT | power_out | Regulated 3.3V output rated for 150 mA, requiring a minimum 10 µF output capacitor with 0.5Ω to 4.0Ω ESR for stability. |
| 3 | GROUND | power_in | Ground pin, with the package tab also connected to ground. |
| 4 | /RESET | output | Active-low open-collector delayed reset output that needs an external pull-up resistor of 10 kΩ to 200 kΩ, with an absolute maximum of -0.3V to 20V. |
| 5 | CDELAY | passive | Reset delay timing capacitor pin, charged at a typical 0.42 µA to set tDELAY = VOUT x (CDELAY/IDELAY), with an absolute maximum of -0.3V to VOUT+0.3V. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage (LM9076-3.3, -20°C to 85°C) | VOUT | 3.251 | 3.3 | 3.349 | V | −20°C ≤ TJ ≤ 85°C | 3 |
| Output voltage (LM9076-3.3, 1 mA to 150 mA) | VOUT | 3.234 | 3.3 | 3.366 | V | 1 mA ≤ ILOAD ≤ 150 mA | 3 |
| Output voltage (LM9076-3.3, 1 mA to 150 mA, full range) | VOUT | 3.201 | 3.3 | 3.399 | V | 1mA ≤ ILOAD ≤ 150 mA | 3 |
| Output voltage (LM9076-3.3, transient) | VOUT | 2.97 | 3.3 | 3.63 | V | VIN = 60V, RLOAD = 1 kΩ, t ≤ 40ms | 3 |
| Output Voltage Off (reverse battery) | -300 | 0 | mV | VIN = -15V, Reverse Battery, RLOAD = 1 kΩ | 3 | ||
| Line regulation (9.0V to 16V) | ΔVOUT | 4 | 25 | mV | 9.0V ≤ VIN ≤ 16V, ILOAD = 10 mA | 3 | |
| Line regulation (16V to 40V) | ΔVOUT | 17 | 35 | mV | 16V ≤ VIN ≤ 40V, ILOAD = 10 mA | 3 | |
| Load regulation | ΔVOUT | 42 | 60 | mV | 1 mA ≤ ILOAD ≤ 150 mA | 3 | |
| Dropout voltage (10 mA) | VDO | 30 | 50 | mV | ILOAD = 10 mA | 3 | |
| Dropout voltage (150 mA) | VDO | 150 | 250 | mV | ILOAD = 150 mA | 3 | |
| Ground pin current (100 uA load) | IGND | 25 | 45 | μA | 9V ≤ VIN ≤ 16V, ILOAD = 100 uA | 3 | |
| Ground pin current (10 mA load) | IGND | 125 | 160 | μA | 9V ≤ VIN ≤ 40V, ILOAD = 10 mA | 3 | |
| Ground pin current (150 mA load) | IGND | 3.6 | 4.5 | mA | 9V ≤ VIN ≤ 16V, ILOAD = 150 mA | 3 | |
| VOUT short circuit current | ISC | 200 | 400 | 750 | mA | VIN = 14V, RLOAD = 1Ω | 3 |
| Ripple rejection | PSRR | 50 | 60 | dB | VIN = (14VDC) + (1VRMS @ 120Hz), ILOAD = 50 mA | 3 | |
| Minimum VIN for valid RESET status | VOR | 1.3 | 2 | V | (Note 3) | 3 | |
| VOUT threshold for RESET low (nom) | VTHR | 0.83 | 0.89 | 0.94 | x VOUT | (Note 3) | 3 |
| RESET pin low voltage | VOL | 0.2 | 0.3 | V | CDELAY < 4.0V, ISINK = 250 µA | 3 | |
| CDELAY charging current | IDELAY | -0.7 | -0.42 | -0.25 | uA | VIN = 14V, VDELAY = 0V | 4 |
| Reset delay time | tDELAY | 4.7 | 7.8 | 13.2 | ms | VIN = 14V, CDELAY = 0.001 uF; VOUT rising from 0V, Δt from VOUT > VOR to RESET pin HIGH | 4 |
| Minimum input voltage DC (absolute maximum) | VIN(DC) | -15 | 55 | V | 2 | ||
| Positive transient input voltage | VIN(+Transient) | 70 | V | t < 10ms, Duty Cycle <1% | 2 | ||
| Negative transient input voltage | VIN(-Transient) | -50 | V | t < 1ms, Duty Cycle <1% | 2 | ||
| RESET pin voltage | -0.3 | 20 | V | 2 | |||
| CDELAY pin voltage (lower limit) | -0.3 | V | upper limit printed as VOUT +0.3V | 2 | |||
| Storage temperature | -65 | 150 | °C | 2 | |||
| Junction temperature (absolute maximum) | TJ | 175 | C | 2 | |||
| ESD HBM | -2 | 2 | kV | per AEC-Q100-002 | 2 | ||
| ESD MM | -250 | 250 | V | per AEC-Q100-003 | 2 | ||
| VIN pin operating range | VIN | 5.35 | 40 | V | 2 | ||
| Junction temperature operating range | TJ | -40 | 125 | °C | 2 | ||
| Thermal resistance junction-to-ambient (KTT0005B) | θJA | 75 | °C/W | KTT0005B; worst case free air per EIA/JESD51-3 (Note 3) | 2 | ||
| Thermal resistance junction-to-case (KTT0005B) | θJC | 2.9 | °C/W | KTT0005B; Note 3 | 2 |
CAD (KiCad official)
- Symbol:
LM9076S-3.3 - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
lm9076s-3-3-etched.step/lm9076s-3-3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm9076s-3-3.step/lm9076s-3-3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (23 pp, sha256
41d0546b0bedab53, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).