Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3517EFE#PBF

Analog Devices · LED Drivers · TSSOP-16-EP

LT3517EFE#PBF from Analog Devices, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply pin that must be locally bypassed, operating from 3V minimum to 30V maximum for continuous operation (40V nonrepetitive transients).
2 SHDN input Shutdown pin: tie to 1.5V or higher to enable the device or 0.4V or less to disable it.
3 VREF power_out Reference output pin (2V typical) that can supply up to 100µA.
4 RT passive Switching frequency adjustment pin: set the frequency with a resistor to GND (250kHz to 2.5MHz), choose 20% slower than the SYNC frequency when synchronizing, and do not leave it open.
5 SYNC input Frequency synchronization pin for an external clock, with the RT resistor set for a switching frequency 20% slower than the SYNC pulse frequency; tie to ground if not used.
6 SS passive Soft-start pin where a soft-start capacitor is placed; leave open if not in use.
7 PWM input Pulse width modulated input: a low signal turns off the channel, disables the main switch and makes the TG pin high; tie to VREF or SHDN if not used, with an internal 50k resistor to ground.
8 CTRL input LED current adjustment pin that sets the voltage across the sense resistor between ISP and ISN: connect to VREF for the full-scale 100mV threshold or use signals between GND and 1V to modulate LED current.
9 VC output gm error amplifier output pin where the loop is stabilized with an RC network or compensating capacitor.
10 FB input Voltage loop feedback pin (1.01V typical threshold) that works as overvoltage protection for LED drivers: if FB is higher than 1V, the main switch is turned off.
11 TGEN input Top gate enable input: tie to 1.5V or higher to enable the PMOS driver function, or to ground if the TG function is not used, with an internal 40k resistor to ground.
12 ISN input Current sense (-) pin, the inverting input to the current sense amplifier.
13 ISP input Current sense (+) pin, the noninverting input to the current sense amplifier, which also serves as the positive rail for the TG pin driver.
14 TG output Top gate driver output: an inverted PWM signal drives a series PMOS device between VISP and (VISP - 7V) with an internal 7V clamp protecting the PMOS gate; leave unconnected if not used.
15 SW passive Switch pin (internal 1.5A, 45V power switch); minimize the trace at this pin to reduce EMI.
16 SW passive Switch pin (internal 1.5A, 45V power switch); minimize the trace at this pin to reduce EMI.
17 GND power_in Exposed pad and the only GND terminal of the IC, which must be soldered directly to the ground plane for electrical and thermal contact.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package TSSOP-16-EP
Category Nixie Tube Driver/LED Driver
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, SHDN, PWM, TGEN voltage VIN 40 V Note 3 2
SW, ISP, ISN, TG voltage SW 45 V 2
TG pin below ISP pin TG 10 V 2
FB, SYNC, SS, CTRL voltage FB 6 V 2
VC, RT, VREF voltage VC 3 V 2
Operating junction temperature range, LT3517E TJ -40 125 °C LT3517E; Notes 2,4 2
Storage temperature range, TSSOP TSTG -65 150 °C TSSOP 2
Lead temperature, soldering 10 sec, TSSOP 300 °C TSSOP 2
Maximum junction temperature TJMAX 150 °C FE (TSSOP) package 2
Thermal resistance, junction to ambient θJA 40 °C/W FE (TSSOP) package 2
Thermal resistance, junction to case (exposed pad) θJC(PAD) 10 °C/W FE (TSSOP) package 2
Minimum VIN operating voltage VIN 3 V 3
Maximum VIN operating voltage VIN 30 V Continuous operation (Note 3) 3
Current sense voltage (VISP - VISN) VISP-VISN 96 100 103 mV VCTRL = 2V, VISP = 24V, VC = 1V 3
10% scale current sense voltage (VISP - VISN) VISP-VISN 9 mV VCTRL = 100mV, VISP = 24V, VC = 1V 3
Current sense voltage line regulation 0.03 %/V 2V < VISP < 45V 3
Switching frequency fSW 0.85 1 1.15 MHz RT = 16.7k 3
Switching frequency fSW 2.25 2.5 2.7 MHz RT = 4.03k 3
Switching frequency fSW 220 250 270 kHz RT = 91.5k 3
Soft-start pin current ISS 6 9 12 µA SS = 0.5V, out of pin 3
Switch current limit ILIM 1.5 1.9 2.3 A 3
VC idle input bias current IVC -20 0 20 nA PWM = 0V, VC = 1V 3
FB pin threshold VFB 0.98 1.01 1.04 V 3
SHDN voltage high VSHDN 1.2 V 3
SHDN voltage low VSHDN 0.45 V -40°C ≤ TJ ≤ 125°C 3
SHDN voltage low VSHDN 0.4 V 125°C < TJ ≤ 150°C 3
PWM input high voltage VPWM 1.2 V 3
PWM input low voltage VPWM 0.45 V -40°C ≤ TJ ≤ 125°C 3
PWM input low voltage VPWM 0.4 V 125°C < TJ ≤ 150°C 3
TGEN input high voltage VTGEN 1.5 V 4
TGEN input low voltage VTGEN 0.4 V 4
VREF pin voltage VREF 1.96 2 2.04 V IREF = -100µA 4
VREF pin voltage line regulation VREF 0.03 %/V 3V < VIN < 40V 4
SYNC input high voltage VSYNC 1.5 V 3
SYNC input low voltage VSYNC 0.4 V 3

CAD (KiCad official)

  • Symbol: LT3517EFE#PBF
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt3517efe-pbf-etched.step / lt3517efe-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3517efe-pbf.step / lt3517efe-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 f2b5ef8803657e31, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF