Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LT3517EFE#PBF
Analog Devices · LED Drivers · TSSOP-16-EP
LT3517EFE#PBF from Analog Devices, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply pin that must be locally bypassed, operating from 3V minimum to 30V maximum for continuous operation (40V nonrepetitive transients). |
| 2 | SHDN | input | Shutdown pin: tie to 1.5V or higher to enable the device or 0.4V or less to disable it. |
| 3 | VREF | power_out | Reference output pin (2V typical) that can supply up to 100µA. |
| 4 | RT | passive | Switching frequency adjustment pin: set the frequency with a resistor to GND (250kHz to 2.5MHz), choose 20% slower than the SYNC frequency when synchronizing, and do not leave it open. |
| 5 | SYNC | input | Frequency synchronization pin for an external clock, with the RT resistor set for a switching frequency 20% slower than the SYNC pulse frequency; tie to ground if not used. |
| 6 | SS | passive | Soft-start pin where a soft-start capacitor is placed; leave open if not in use. |
| 7 | PWM | input | Pulse width modulated input: a low signal turns off the channel, disables the main switch and makes the TG pin high; tie to VREF or SHDN if not used, with an internal 50k resistor to ground. |
| 8 | CTRL | input | LED current adjustment pin that sets the voltage across the sense resistor between ISP and ISN: connect to VREF for the full-scale 100mV threshold or use signals between GND and 1V to modulate LED current. |
| 9 | VC | output | gm error amplifier output pin where the loop is stabilized with an RC network or compensating capacitor. |
| 10 | FB | input | Voltage loop feedback pin (1.01V typical threshold) that works as overvoltage protection for LED drivers: if FB is higher than 1V, the main switch is turned off. |
| 11 | TGEN | input | Top gate enable input: tie to 1.5V or higher to enable the PMOS driver function, or to ground if the TG function is not used, with an internal 40k resistor to ground. |
| 12 | ISN | input | Current sense (-) pin, the inverting input to the current sense amplifier. |
| 13 | ISP | input | Current sense (+) pin, the noninverting input to the current sense amplifier, which also serves as the positive rail for the TG pin driver. |
| 14 | TG | output | Top gate driver output: an inverted PWM signal drives a series PMOS device between VISP and (VISP - 7V) with an internal 7V clamp protecting the PMOS gate; leave unconnected if not used. |
| 15 | SW | passive | Switch pin (internal 1.5A, 45V power switch); minimize the trace at this pin to reduce EMI. |
| 16 | SW | passive | Switch pin (internal 1.5A, 45V power switch); minimize the trace at this pin to reduce EMI. |
| 17 | GND | power_in | Exposed pad and the only GND terminal of the IC, which must be soldered directly to the ground plane for electrical and thermal contact. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSSOP-16-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, SHDN, PWM, TGEN voltage | VIN | 40 | V | Note 3 | 2 | ||
| SW, ISP, ISN, TG voltage | SW | 45 | V | 2 | |||
| TG pin below ISP pin | TG | 10 | V | 2 | |||
| FB, SYNC, SS, CTRL voltage | FB | 6 | V | 2 | |||
| VC, RT, VREF voltage | VC | 3 | V | 2 | |||
| Operating junction temperature range, LT3517E | TJ | -40 | 125 | °C | LT3517E; Notes 2,4 | 2 | |
| Storage temperature range, TSSOP | TSTG | -65 | 150 | °C | TSSOP | 2 | |
| Lead temperature, soldering 10 sec, TSSOP | 300 | °C | TSSOP | 2 | |||
| Maximum junction temperature | TJMAX | 150 | °C | FE (TSSOP) package | 2 | ||
| Thermal resistance, junction to ambient | θJA | 40 | °C/W | FE (TSSOP) package | 2 | ||
| Thermal resistance, junction to case (exposed pad) | θJC(PAD) | 10 | °C/W | FE (TSSOP) package | 2 | ||
| Minimum VIN operating voltage | VIN | 3 | V | 3 | |||
| Maximum VIN operating voltage | VIN | 30 | V | Continuous operation (Note 3) | 3 | ||
| Current sense voltage (VISP - VISN) | VISP-VISN | 96 | 100 | 103 | mV | VCTRL = 2V, VISP = 24V, VC = 1V | 3 |
| 10% scale current sense voltage (VISP - VISN) | VISP-VISN | 9 | mV | VCTRL = 100mV, VISP = 24V, VC = 1V | 3 | ||
| Current sense voltage line regulation | 0.03 | %/V | 2V < VISP < 45V | 3 | |||
| Switching frequency | fSW | 0.85 | 1 | 1.15 | MHz | RT = 16.7k | 3 |
| Switching frequency | fSW | 2.25 | 2.5 | 2.7 | MHz | RT = 4.03k | 3 |
| Switching frequency | fSW | 220 | 250 | 270 | kHz | RT = 91.5k | 3 |
| Soft-start pin current | ISS | 6 | 9 | 12 | µA | SS = 0.5V, out of pin | 3 |
| Switch current limit | ILIM | 1.5 | 1.9 | 2.3 | A | 3 | |
| VC idle input bias current | IVC | -20 | 0 | 20 | nA | PWM = 0V, VC = 1V | 3 |
| FB pin threshold | VFB | 0.98 | 1.01 | 1.04 | V | 3 | |
| SHDN voltage high | VSHDN | 1.2 | V | 3 | |||
| SHDN voltage low | VSHDN | 0.45 | V | -40°C ≤ TJ ≤ 125°C | 3 | ||
| SHDN voltage low | VSHDN | 0.4 | V | 125°C < TJ ≤ 150°C | 3 | ||
| PWM input high voltage | VPWM | 1.2 | V | 3 | |||
| PWM input low voltage | VPWM | 0.45 | V | -40°C ≤ TJ ≤ 125°C | 3 | ||
| PWM input low voltage | VPWM | 0.4 | V | 125°C < TJ ≤ 150°C | 3 | ||
| TGEN input high voltage | VTGEN | 1.5 | V | 4 | |||
| TGEN input low voltage | VTGEN | 0.4 | V | 4 | |||
| VREF pin voltage | VREF | 1.96 | 2 | 2.04 | V | IREF = -100µA | 4 |
| VREF pin voltage line regulation | VREF | 0.03 | %/V | 3V < VIN < 40V | 4 | ||
| SYNC input high voltage | VSYNC | 1.5 | V | 3 | |||
| SYNC input low voltage | VSYNC | 0.4 | V | 3 |
CAD (KiCad official)
- Symbol:
LT3517EFE#PBF - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt3517efe-pbf-etched.step/lt3517efe-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3517efe-pbf.step/lt3517efe-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
f2b5ef8803657e31, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).