Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS54418ARTER

Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)

TPS54418ARTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply voltage, 2.95 V to 6 V.
2 VIN power_in Input supply voltage, 2.95 V to 6 V.
3 GND power_in Power ground; this pin should be electrically connected directly to the power pad under the device.
4 GND power_in Power ground; this pin should be electrically connected directly to the power pad under the device.
5 AGND power_in Analog ground should be electrically connected to GND close to the device.
6 VSENSE input Inverting node of the transconductance (gm) error amplifier.
7 COMP output Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin.
8 RT/CLK bidirectional Resistor timing or external clock input pin.
9 SS bidirectional Slow-start pin; an external capacitor connected to this pin sets the output voltage rise time.
10 PH output Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET.
11 PH output Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET.
12 PH output Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET.
13 BOOT input A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the BOOT UVLO minimum, the output is forced off until the capacitor is refreshed.
14 PWRGD output Open-drain output that asserts low if output voltage is low due to thermal shutdown, overcurrent, over/under-voltage or EN shutdown; absolute maximum sink current is 10 mA.
15 EN input Enable pin with internal pull-up current source; pull below 1.2 V to disable and float to enable, and can set the on/off threshold with two additional resistors.
16 VIN power_in Input supply voltage, 2.95 V to 6 V.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-16-EP(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage EN, PWRGD, VIN -0.3 7 V 4
Input voltage RT/CLK -0.3 6 V 4
Input voltage COMP, SS, VSENSE -0.3 3 V 4
Output voltage BOOT-PH 8 V 4
Output voltage PH -0.6 7 V 4
Output voltage PH (10 ns transient) -2 7 V 10 ns transient 4
Source current EN, RT/CLK 100 µA 4
Sink current COMP, SS 100 µA 4
Sink current PWRGD 10 mA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input voltage VVIN 3 6 V 4
Operating junction temperature TJ -40 150 °C 4
Junction-to-ambient thermal resistance RθJA 50 °C/W 4
Junction-to-ambient thermal resistance (test board) RθJA 37 °C/W JEDEC high-K test board, 2 oz copper, 4 thermal vias 4
Junction-to-case (top) thermal resistance RθJC(top) 59.1 °C/W 4
Junction-to-board thermal resistance RθJB 23.1 °C/W 4
Junction-to-top characterization parameter ψJT 1.4 °C/W 4
Junction-to-board characterization parameter ψJB 23.1 °C/W 4
Junction-to-case (bottom) thermal resistance RθJC(bot) 7.9 °C/W 4
Operating input voltage VVIN 2.95 6 V 5
Internal under voltage lockout threshold VUVLO 2.6 2.8 V No voltage hysteresis, rising and falling 5
Shutdown supply current IQ(vin) 2 5 µA VEN = 0 V, TA = 25°C, 2.95 V ≤ VVIN ≤ 6 V 5
Quiescent current Iq 350 500 µA VVSENSE = 0.9 V, VVIN = 5 V, 25°C, RT = 400 kΩ 5
Enable threshold rising VTH(en) 1.16 1.25 1.37 V Rising 5
Voltage reference VREF 0.795 0.803 0.811 V 2.95 V ≤ VVIN ≤ 6 V, -40°C <TJ < 150°C 5
High-side switch resistance RDS(HFET) 30 60 mΩ (VBOOT, VPH) = 5 V 5
High-side switch resistance RDS(HFET) 44 70 mΩ (VBOOT, VPH) = 2.95 V 5
Low-side switch resistance RDS(LFET) 30 60 mΩ VVIN = 5 V 5
Low-side switch resistance RDS(LFET) 44 70 mΩ VVIN = 2.95 V 5
Error amplifier source/sink current ICOMP -20 20 µA VCOMP = 1 V, 100 mV overdrive 5
Current limit threshold ILIM 5 6.4 A Instantaneous peak current 5
Switching frequency range using RT mode fSW 200 2000 kHz 5
Switching frequency fSW 400 500 600 kHz RRT = 400 kΩ 5
Switching frequency range using CLK mode fSW 300 2000 kHz 5
RT/CLK high threshold VIH(CLK) 1.6 2.2 V 5
RT/CLK low threshold VIL(CLK) 0.4 0.6 V 5
Minimum on time tON(min) 60 ns Measured at 50% points on PH, IOUT = 4 A 6
Minimum on time tON(min) 110 ns Measured at 50% points on PH, VIN = 5 V, IOUT = 0 A 6
Minimum off time tOFF(min) 60 ns Prior to skipping off pulses, (VBOOT, VPH) = 2.95 V, IOUT = 4 A 6
Boot-PH UVLO VUVLO(Boot) 2.1 V VVIN = 2.95 V 6
Thermal shutdown TSD 175 °C 5
Thermal shutdown hysteresis TSD(hyst) 15 °C 5
Minimum CLK pulse width tMIN(CLK) 75 ns 5
RT/CLK voltage VRT/CLK 0.5 V RRT/CLK = 400 kΩ 5
RT/CLK falling edge to PH rising edge delay tDLY 90 ns fSW = 500 kHz with RRT resistor in series 5
PLL lock-in time tLOCK(PLL) 14 µs fSW = 500 kHz 5
Error amplifier transconductance gM(ea) 225 µS -2 µA < ICOMP < 2 µA, VCOMP = 1 V 5
Error amplifier transconductance during soft-start gm(EA,ss) 70 µS -2 µA < ICOMP < 2 µA, VCOMP = 1 V, VVSENSE = 0.4 V 5
COMP to ISWITCH transconductance gM 13 A/V 5
Charge current ICHG 1.8 µA VSS = 0.4 V 6
SS to reference crossover VSSxREF 0.9 V 98% nominal 6
SS discharge voltage (overload) VDSCHG(SS) 20 µA VVSENSE = 0 V 6
SS discharge current (UVLO, EN, thermal fault) IDSCHG(SS) 1.25 mA VVIN = 5 V, VSS = 0.5 V 6
VSENSE threshold falling (fault) VTH(PG) 91 %VREF VVSENSE falling (fault) 6
VSENSE threshold rising (good) VTH(PG) 93 %VREF VVSENSE rising (good) 6
VSENSE threshold rising (fault) VTH(PG) 107 %VREF VVSENSE rising (fault) 6
VSENSE threshold falling (good) VTH(PG) 105 %VREF VVSENSE falling (Good) 6
Hysteresis VHYST(PG) 2 %VREF VVSENSE falling 6
Output high leakage IPH(lkg) 2 nA VVSENSE = VREF, VPWRGD = 5.5 V 6
Power Good on-resistance RPG 100 Ω 6
Low-level output voltage VOL 0.3 V IPWRGD = 3.5 mA 6
Minimum input voltage for valid output VMIN(PG) 1.2 1.6 V VPWRGD < 0.5 V, IOUT = 100 µA 6

CAD (KiCad official)

  • Symbol: TPS54418ARTER
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps54418arter-etched.step / tps54418arter-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54418arter.step / tps54418arter.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (41 pp, sha256 7922646d2a63a9e5, retrieved 2026-10-28, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF