3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS54418ARTER
Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)
TPS54418ARTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage, 2.95 V to 6 V. |
| 2 | VIN | power_in | Input supply voltage, 2.95 V to 6 V. |
| 3 | GND | power_in | Power ground; this pin should be electrically connected directly to the power pad under the device. |
| 4 | GND | power_in | Power ground; this pin should be electrically connected directly to the power pad under the device. |
| 5 | AGND | power_in | Analog ground should be electrically connected to GND close to the device. |
| 6 | VSENSE | input | Inverting node of the transconductance (gm) error amplifier. |
| 7 | COMP | output | Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin. |
| 8 | RT/CLK | bidirectional | Resistor timing or external clock input pin. |
| 9 | SS | bidirectional | Slow-start pin; an external capacitor connected to this pin sets the output voltage rise time. |
| 10 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 11 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 12 | PH | output | Source of the internal high-side power MOSFET and drain of the internal low-side (synchronous) rectifier MOSFET. |
| 13 | BOOT | input | A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the BOOT UVLO minimum, the output is forced off until the capacitor is refreshed. |
| 14 | PWRGD | output | Open-drain output that asserts low if output voltage is low due to thermal shutdown, overcurrent, over/under-voltage or EN shutdown; absolute maximum sink current is 10 mA. |
| 15 | EN | input | Enable pin with internal pull-up current source; pull below 1.2 V to disable and float to enable, and can set the on/off threshold with two additional resistors. |
| 16 | VIN | power_in | Input supply voltage, 2.95 V to 6 V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage EN, PWRGD, VIN | -0.3 | 7 | V | 4 | |||
| Input voltage RT/CLK | -0.3 | 6 | V | 4 | |||
| Input voltage COMP, SS, VSENSE | -0.3 | 3 | V | 4 | |||
| Output voltage BOOT-PH | 8 | V | 4 | ||||
| Output voltage PH | -0.6 | 7 | V | 4 | |||
| Output voltage PH (10 ns transient) | -2 | 7 | V | 10 ns transient | 4 | ||
| Source current EN, RT/CLK | 100 | µA | 4 | ||||
| Sink current COMP, SS | 100 | µA | 4 | ||||
| Sink current PWRGD | 10 | mA | 4 | ||||
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage | VVIN | 3 | 6 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 50 | °C/W | 4 | |||
| Junction-to-ambient thermal resistance (test board) | RθJA | 37 | °C/W | JEDEC high-K test board, 2 oz copper, 4 thermal vias | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 59.1 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 23.1 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 1.4 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 23.1 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.9 | °C/W | 4 | |||
| Operating input voltage | VVIN | 2.95 | 6 | V | 5 | ||
| Internal under voltage lockout threshold | VUVLO | 2.6 | 2.8 | V | No voltage hysteresis, rising and falling | 5 | |
| Shutdown supply current | IQ(vin) | 2 | 5 | µA | VEN = 0 V, TA = 25°C, 2.95 V ≤ VVIN ≤ 6 V | 5 | |
| Quiescent current | Iq | 350 | 500 | µA | VVSENSE = 0.9 V, VVIN = 5 V, 25°C, RT = 400 kΩ | 5 | |
| Enable threshold rising | VTH(en) | 1.16 | 1.25 | 1.37 | V | Rising | 5 |
| Voltage reference | VREF | 0.795 | 0.803 | 0.811 | V | 2.95 V ≤ VVIN ≤ 6 V, -40°C <TJ < 150°C | 5 |
| High-side switch resistance | RDS(HFET) | 30 | 60 | mΩ | (VBOOT, VPH) = 5 V | 5 | |
| High-side switch resistance | RDS(HFET) | 44 | 70 | mΩ | (VBOOT, VPH) = 2.95 V | 5 | |
| Low-side switch resistance | RDS(LFET) | 30 | 60 | mΩ | VVIN = 5 V | 5 | |
| Low-side switch resistance | RDS(LFET) | 44 | 70 | mΩ | VVIN = 2.95 V | 5 | |
| Error amplifier source/sink current | ICOMP | -20 | 20 | µA | VCOMP = 1 V, 100 mV overdrive | 5 | |
| Current limit threshold | ILIM | 5 | 6.4 | A | Instantaneous peak current | 5 | |
| Switching frequency range using RT mode | fSW | 200 | 2000 | kHz | 5 | ||
| Switching frequency | fSW | 400 | 500 | 600 | kHz | RRT = 400 kΩ | 5 |
| Switching frequency range using CLK mode | fSW | 300 | 2000 | kHz | 5 | ||
| RT/CLK high threshold | VIH(CLK) | 1.6 | 2.2 | V | 5 | ||
| RT/CLK low threshold | VIL(CLK) | 0.4 | 0.6 | V | 5 | ||
| Minimum on time | tON(min) | 60 | ns | Measured at 50% points on PH, IOUT = 4 A | 6 | ||
| Minimum on time | tON(min) | 110 | ns | Measured at 50% points on PH, VIN = 5 V, IOUT = 0 A | 6 | ||
| Minimum off time | tOFF(min) | 60 | ns | Prior to skipping off pulses, (VBOOT, VPH) = 2.95 V, IOUT = 4 A | 6 | ||
| Boot-PH UVLO | VUVLO(Boot) | 2.1 | V | VVIN = 2.95 V | 6 | ||
| Thermal shutdown | TSD | 175 | °C | 5 | |||
| Thermal shutdown hysteresis | TSD(hyst) | 15 | °C | 5 | |||
| Minimum CLK pulse width | tMIN(CLK) | 75 | ns | 5 | |||
| RT/CLK voltage | VRT/CLK | 0.5 | V | RRT/CLK = 400 kΩ | 5 | ||
| RT/CLK falling edge to PH rising edge delay | tDLY | 90 | ns | fSW = 500 kHz with RRT resistor in series | 5 | ||
| PLL lock-in time | tLOCK(PLL) | 14 | µs | fSW = 500 kHz | 5 | ||
| Error amplifier transconductance | gM(ea) | 225 | µS | -2 µA < ICOMP < 2 µA, VCOMP = 1 V | 5 | ||
| Error amplifier transconductance during soft-start | gm(EA,ss) | 70 | µS | -2 µA < ICOMP < 2 µA, VCOMP = 1 V, VVSENSE = 0.4 V | 5 | ||
| COMP to ISWITCH transconductance | gM | 13 | A/V | 5 | |||
| Charge current | ICHG | 1.8 | µA | VSS = 0.4 V | 6 | ||
| SS to reference crossover | VSSxREF | 0.9 | V | 98% nominal | 6 | ||
| SS discharge voltage (overload) | VDSCHG(SS) | 20 | µA | VVSENSE = 0 V | 6 | ||
| SS discharge current (UVLO, EN, thermal fault) | IDSCHG(SS) | 1.25 | mA | VVIN = 5 V, VSS = 0.5 V | 6 | ||
| VSENSE threshold falling (fault) | VTH(PG) | 91 | %VREF | VVSENSE falling (fault) | 6 | ||
| VSENSE threshold rising (good) | VTH(PG) | 93 | %VREF | VVSENSE rising (good) | 6 | ||
| VSENSE threshold rising (fault) | VTH(PG) | 107 | %VREF | VVSENSE rising (fault) | 6 | ||
| VSENSE threshold falling (good) | VTH(PG) | 105 | %VREF | VVSENSE falling (Good) | 6 | ||
| Hysteresis | VHYST(PG) | 2 | %VREF | VVSENSE falling | 6 | ||
| Output high leakage | IPH(lkg) | 2 | nA | VVSENSE = VREF, VPWRGD = 5.5 V | 6 | ||
| Power Good on-resistance | RPG | 100 | Ω | 6 | |||
| Low-level output voltage | VOL | 0.3 | V | IPWRGD = 3.5 mA | 6 | ||
| Minimum input voltage for valid output | VMIN(PG) | 1.2 | 1.6 | V | VPWRGD < 0.5 V, IOUT = 100 µA | 6 |
CAD (KiCad official)
- Symbol:
TPS54418ARTER - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps54418arter-etched.step/tps54418arter-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54418arter.step/tps54418arter.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
7922646d2a63a9e5, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).