component
DRV8800PWPR
Public Made by Adomby adom
Texas Instruments Brushed DC Motor Drivers, TSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownDRV8800PWPR
Texas Instruments · Brushed DC Motor Drivers · TSSOP-16-EP
DRV8800PWPR from Texas Instruments, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | nFAULT | output | Open-drain fault output, pulled low on motor fault, supply undervoltage, or junction temperature exceeding 160°C; requires external pullup resistor. |
| 2 | MODE | input | Mode selection input. Logic high selects slow-decay mode, logic low selects fast-decay mode. Input threshold VIH ≥ 2V, VIL ≤ 0.8V. |
| 3 | PHASE | input | Phase/direction control input. Logic high = forward, logic low = reverse. Controls H-bridge direction. Input threshold VIH ≥ 2V, VIL ≤ 0.8V. |
| 4 | GND | power_in | Device ground and return path for power supply and signal circuits. |
| 5 | nSLEEP | input | Sleep mode enable input. Logic high enables device operation, logic low enters low-power sleep mode with <10µA quiescent current. Internal pulldown resistor. Input threshold VIH ≥ 2.7V, VIL ≤ 0.8V. |
| 6 | ENABLE | input | Output enable control input. Logic high enables H-bridge, logic low disables output. Input threshold VIH ≥ 2V, VIL ≤ 0.8V. |
| 7 | OUT+ | output | H-bridge positive output to motor. Rated for ±2.8A peak current, typical RDS(on) = 0.4Ω at 25°C, 0.7Ω at 125°C. |
| 8 | SENSE | output | Current sense return output. Connect external 0.2Ω sense resistor between SENSE pin and ground to set overcurrent threshold at 500mV (2.8A typical); adjustable via RSENSE value. |
| 9 | VBB | power_in | Motor driver supply voltage input, operating range 8V to 36V. Bypass to GND with 0.1µF ceramic + 100µF bulk capacitor. Undervoltage lockout threshold 6.5V rising. |
| 10 | OUT- | output | H-bridge negative output to motor. Rated for ±2.8A peak current, typical RDS(on) = 0.4Ω at 25°C, 0.7Ω at 125°C. |
| 11 | CP1 | passive | Charge pump switching node. Connect 0.1µF X7R ceramic capacitor between CP1 and CP2; capacitor must be rated for VBB voltage. |
| 12 | CP2 | passive | Charge pump switching node. Connect 0.1µF X7R ceramic capacitor between CP1 and CP2; capacitor must be rated for VBB voltage. |
| 13 | GND | power_in | Device ground and return path for power supply and signal circuits. |
| 14 | VCP | power_out | Charge pump output and gate drive supply reservoir. Connect 0.1µF 16V X7R ceramic capacitor to VBB. Monitored internally; outputs disable if VCP falls below charge pump undervoltage threshold. |
| 15 | VREG | output | Regulated 7.5V reference voltage output. Leave disconnected in normal operation; provides internal regulator voltage reference measurement point. Do not load. |
| 16 | NC | unconnected | No connection. Must remain unconnected to any circuit node. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16-EP |
| Category | Motor Driver ICs |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
DRV8800PWPR - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
drv8800pwpr-etched.step/drv8800pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);drv8800pwpr.step/drv8800pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
8498d1c74347b1a9, retrieved 2026-09-21, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).