Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ADS127L01IPBS

Texas Instruments · Analog To Digital Converters (ADC) · TQFP-32(5x5)

ADS127L01IPBS from Texas Instruments, in a TQFP-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 LVDD power_out 1.8-V analog supply from internal LDO regulator (INTLDO=0) or input (INTLDO=1); decouple with 1-µF capacitor to AGND.
2 CAP1 output Modulator common-mode voltage output; connect a 1-µF capacitor to AGND.
3 AINN input Negative differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V).
4 AINP input Positive differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V).
5 AGND power_in Analog ground reference.
6 AVDD power_in Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND.
7 REXT input Analog power-scaling bias resistor pin; connect 60.4-kΩ resistor (HR/LP modes) or 120-kΩ (VLP mode) to AGND.
8 INTLDO input LVDD voltage selection pin; pull high to AVDD (external 1.8-V supply) or low to AGND (internal LDO) through 10-kΩ resistor.
9 REFP input Positive analog reference input; connect minimum 10-µF capacitor between REFP and REFN.
10 REFN input Negative analog reference input.
11 CAP2 output Reference common-mode voltage output; connect a 1-µF capacitor to AGND.
12 FILTER1 input Digital filter select pin bit 1; pull high to DVDD or low to DGND through 100-kΩ resistor.
13 FILTER0 input Digital filter select pin bit 0; pull high/low through 100-kΩ resistor; 00=WB1, 01=WB2, 10=LL, 11=Reserved.
14 FSMODE input Frame-sync mode select pin; pull high (master mode) or low (slave mode) through 100-kΩ resistor; applies to Frame-Sync interface only.
15 OSR1 input Oversampling ratio select pin bit 1 for decimation filters; pull high/low through 100-kΩ resistor.
16 OSR0 input Oversampling ratio select pin bit 0; pull high/low through 100-kΩ resistor; wideband filters 00=32x, 01=64x, 10=128x, 11=256x.
17 START input Synchronization signal (active high) to start or restart ADC conversion.
18 DAISYIN input Daisy-chain input for cascaded device configurations; tie directly to DGND if not daisy-chaining.
19 DRDY/FSYNC bidirectional SPI interface: data ready output (active low); Frame-sync interface: frame-sync input signal for synchronization.
20 DOUT output Serial data output from ADC (24-bit or 32-bit format); high-impedance when CS=1 in cascaded SPI configurations.
21 DIN input Serial data input for SPI interface; tie directly to DGND when using frame-sync interface mode.
22 SCLK bidirectional Serial clock input for SPI interface (0 to DVDD+0.3V); functions as input/output depending on interface configuration.
23 CS input Chip select input (active high in SPI cascaded configurations); tie directly to DGND when using frame-sync interface; controls DOUT tri-state.
24 CLK input Master clock input for internal timing and ADC modulator operation.
25 CAP3 output Internally-generated digital operating voltage output; connect a 1-µF capacitor to DGND.
26 DGND power_in Digital ground reference.
27 DVDD power_in Digital-supply voltage input (1.7V to 3.6V); connect a 1-µF capacitor to DGND.
28 RESET/PWDN input Reset or power-down pin (active low); asynchronous reset of all registers when pulled low.
29 HR input ADC operating mode select; pull high to DVDD (high-resolution mode) or low to DGND (LP/VLP mode) through 100-kΩ resistor.
30 FORMAT input Interface protocol select; pull high to DVDD (Frame-Sync mode) or low to DGND (SPI mode) through 100-kΩ resistor.
31 AGND power_in Analog ground reference.
32 AVDD power_in Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TQFP-32(5x5)
Category Data Acquisition
Pins 32

CAD (KiCad official)

  • Symbol: ADS127L01IPBS
  • Footprint: Package_QFP:TQFP-32_5x5mm_P0.5mm
  • 3D model: TQFP-32(5x5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm nominal TQFP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: ads127l01ipbs-etched.step / ads127l01ipbs-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ads127l01ipbs.step / ads127l01ipbs.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (90 pp, sha256 7af2117fe188e693, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF