Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LP2986AIM-5.0

Texas Instruments · Linear Voltage Regulators (LDO) · SOIC-8

LP2986AIM-5.0 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GROUND power_in Ground reference pin of the regulator; the WSON thermal pad is recommended to be tied directly to this pin's ground.
2 FEEDBACK input Sets the output voltage: tie to TAP (with OUT tied to SENSE) for the fixed version, or drive from a resistor divider for an adjustable output; the absolute maximum rating is -0.3 V to 5 V.
3 TAP output Middle tap of the internal voltage divider, to be tied to FEEDBACK (with OUT tied to SENSE) to output the fixed voltage of the part version.
4 IN power_in Input voltage supply, operating from 2.1 V to 16 V, with a 16 V survival rating.
5 OUT power_out Regulated output, rated for up to 200 mA of output current.
6 SENSE input Connect to OUT (with FEEDBACK tied to TAP) to output the fixed voltage of the part version.
7 ERROR output Active-low open-collector error output that goes low when VOUT drops about 5% below nominal; it requires an external pull-up and is rated to sink up to 300 µA.
8 SHUTDOWN input Active-high enable: pull low to shut down the output; the absolute maximum rating is -0.3 V to 16 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input supply voltage (survival) -0.3 16 V Over operating free-air temperature range 4
SHUTDOWN pin -0.3 16 V Over operating free-air temperature range 4
FEEDBACK pin -0.3 5 V Over operating free-air temperature range 4
Output voltage (survival) -0.3 16 V Over operating free-air temperature range 4
Input-output voltage (survival) -0.3 16 V Over operating free-air temperature range 4
Storage temperature Tstg -65 150 °C 4
Supply input voltage 2.1 16 V Over operating free-air temperature range 4
Enable input voltage 0 16 V Over operating free-air temperature range 4
Output current 200 mA Over operating free-air temperature range 4
Operating junction temperature TJ -40 125 °C Over operating free-air temperature range 4
Junction-to-ambient thermal resistance (SOIC, D package) RθJA 114.4 °C/W High-K board, EIA/JEDEC JESD51-7 5
Junction-to-board thermal resistance (SOIC, D package) RθJB 55.5 °C/W 5
Output voltage (5-V version) VOUT 4.975 5 5.025 V 5
Output voltage (5-V version) VOUT 4.96 5 5.04 V 0.1 mA < IOUT < 200 mA 5
Output voltage (5-V version) VOUT 4.91 5.09 V 0.1 mA < IOUT < 200 mA, -40°C ≤ TJ ≤ 125°C 5
Output voltage line regulation ΔVOUT/ΔVIN 0.007 0.014 %/V VOUT(NOM) + 1 V ≤ VIN ≤ 16 V 5
Output voltage line regulation ΔVOUT/ΔVIN 0.032 %/V VOUT(NOM) + 1 V ≤ VIN ≤ 16 V, -40°C ≤ TJ ≤ 125°C 5
Dropout voltage VIN, VOUT 1 2 mV IOUT = 100 µA 5
Dropout voltage VIN, VOUT 3.5 mV IOUT = 100 µA, -40°C ≤ TJ ≤ 125°C 5
Dropout voltage VIN, VOUT 90 120 mV IOUT = 75 mA 5
Dropout voltage VIN, VOUT 170 mV IOUT = 75 mA, -40°C ≤ TJ ≤ 125°C 5
Dropout voltage VIN, VOUT 180 230 mV IOUT = 200 mA 5
Dropout voltage VIN, VOUT 350 mV IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C 5
Ground pin current IGND 100 120 µA IOUT = 100 µA 6
Ground pin current IGND 150 µA IOUT = 100 µA, -40°C ≤ TJ ≤ 125°C 6
Ground pin current IGND 500 800 µA IOUT = 75 mA 6
Ground pin current IGND 1400 µA IOUT = 75 mA, -40°C ≤ TJ ≤ 125°C 6
Ground pin current IGND 1 2.1 mA IOUT = 200 mA 6
Ground pin current IGND 3.7 mA IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C 6
Ground pin current in shutdown IGND 0.05 µA VSD < 0.3 V 6
Ground pin current in shutdown IGND 1.5 µA VSD < 0.3 V, -40°C ≤ TJ ≤ 125°C 6
Peak output current IOUT(PK) 250 400 mA VOUT ≥ VOUT(NOM) − 5% 6
Short-circuit current IOUT(MAX) 400 mA RL = 0 (steady state) 6
Output noise voltage en 160 µVRMS BW = 300 Hz to 50 kHz, COUT = 10 µF 6
Ripple rejection ΔVOUT/ΔVIN 65 dB f = 1 kHz, COUT = 10 µF 6
Output voltage temperature coefficient ΔVOUT/ΔTD 20 ppm/°C See note (4) 6
FEEDBACK pin voltage VFB 1.21 1.23 1.25 V 6
FEEDBACK pin voltage VFB 1.2 1.26 V -40°C ≤ TJ ≤ 125°C 6
FEEDBACK pin voltage VFB 1.19 1.28 V See note (5): VFB ≤ VOUT ≤ (VIN − 1), 2.5 V ≤ VIN ≤ 16 V, 100 µA ≤ IL ≤ 200 mA, TJ ≤ 125°C 6
FEEDBACK pin voltage temperature coefficient ΔVFB/ΔT 20 ppm/°C See note (6) 6
FEEDBACK pin bias current IFB 150 330 nA IOUT = 200 mA 6
FEEDBACK pin bias current IFB 760 nA IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C 6
FEEDBACK pin bias current temperature coefficient ΔIFB/ΔT 0.1 nA/°C See note (6) 6
SHUTDOWN input voltage (output ON) VH 1.4 V VH = Output ON 6
SHUTDOWN input voltage (output ON) VH 1.6 V VH = Output ON, -40°C ≤ TJ ≤ 125°C 6
SHUTDOWN input voltage (output OFF) VL 0.55 V VL = Output OFF 6
SHUTDOWN input voltage (output OFF) VL 0.18 V VL = Output OFF, -40°C ≤ TJ ≤ 125°C 6
SHUTDOWN input current ISD 0 µA VSD = 0 V 6
SHUTDOWN input current ISD -1 µA VSD = 0 V, -40°C ≤ TJ ≤ 125°C 6
SHUTDOWN input current ISD 5 µA VSD = 5 V 6
SHUTDOWN input current ISD 15 µA VSD = 5 V, -40°C ≤ TJ ≤ 125°C 6
Output HIGH leakage current IOH 0.01 1 µA VOH = 16 V 7
Output HIGH leakage current IOH 2 µA VOH = 16 V, -40°C ≤ TJ ≤ 125°C 7
ERROR comparator row (label not printed in extracted text) 150 220 µA VIN = VOUT(NOM) − 0.5 V, IOUT(COMP) = 300 µA 7
Output LOW voltage (ERROR) VOL 350 mV VIN = VOUT(NOM) − 0.5 V, IOUT(COMP) = 300 µA 7
Upper threshold voltage VTHR(MAX) -5.5 -4.6 -3.5 %VOUT 7
Upper threshold voltage VTHR(MAX) -7.7 -2.5 %VOUT -40°C ≤ TJ ≤ 125°C 7
Lower threshold voltage VTHR(MIN) -8.9 -6.6 -4.9 %VOUT 7
Lower threshold voltage VTHR(MIN) -13 -3.3 %VOUT -40°C ≤ TJ ≤ 125°C 7
Hysteresis HYST 2 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper capacitor, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side, copper surface. The use of vias and long traces to create LDO circuit connections is stron 20

CAD (KiCad official)

  • Symbol: LP2986AIM-5.0
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: lp2986aim-5-0-etched.step / lp2986aim-5-0-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp2986aim-5-0.step / lp2986aim-5-0.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (38 pp, sha256 e7d8f233a69ce5e5, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF