component
LP2986AIM-5.0
Public Made by Adomby adom
Texas Instruments Linear Voltage Regulators (LDO), SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLP2986AIM-5.0
Texas Instruments · Linear Voltage Regulators (LDO) · SOIC-8
LP2986AIM-5.0 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GROUND | power_in | Ground reference pin of the regulator; the WSON thermal pad is recommended to be tied directly to this pin's ground. |
| 2 | FEEDBACK | input | Sets the output voltage: tie to TAP (with OUT tied to SENSE) for the fixed version, or drive from a resistor divider for an adjustable output; the absolute maximum rating is -0.3 V to 5 V. |
| 3 | TAP | output | Middle tap of the internal voltage divider, to be tied to FEEDBACK (with OUT tied to SENSE) to output the fixed voltage of the part version. |
| 4 | IN | power_in | Input voltage supply, operating from 2.1 V to 16 V, with a 16 V survival rating. |
| 5 | OUT | power_out | Regulated output, rated for up to 200 mA of output current. |
| 6 | SENSE | input | Connect to OUT (with FEEDBACK tied to TAP) to output the fixed voltage of the part version. |
| 7 | ERROR | output | Active-low open-collector error output that goes low when VOUT drops about 5% below nominal; it requires an external pull-up and is rated to sink up to 300 µA. |
| 8 | SHUTDOWN | input | Active-high enable: pull low to shut down the output; the absolute maximum rating is -0.3 V to 16 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage (survival) | -0.3 | 16 | V | Over operating free-air temperature range | 4 | ||
| SHUTDOWN pin | -0.3 | 16 | V | Over operating free-air temperature range | 4 | ||
| FEEDBACK pin | -0.3 | 5 | V | Over operating free-air temperature range | 4 | ||
| Output voltage (survival) | -0.3 | 16 | V | Over operating free-air temperature range | 4 | ||
| Input-output voltage (survival) | -0.3 | 16 | V | Over operating free-air temperature range | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Supply input voltage | 2.1 | 16 | V | Over operating free-air temperature range | 4 | ||
| Enable input voltage | 0 | 16 | V | Over operating free-air temperature range | 4 | ||
| Output current | 200 | mA | Over operating free-air temperature range | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | Over operating free-air temperature range | 4 | |
| Junction-to-ambient thermal resistance (SOIC, D package) | RθJA | 114.4 | °C/W | High-K board, EIA/JEDEC JESD51-7 | 5 | ||
| Junction-to-board thermal resistance (SOIC, D package) | RθJB | 55.5 | °C/W | 5 | |||
| Output voltage (5-V version) | VOUT | 4.975 | 5 | 5.025 | V | 5 | |
| Output voltage (5-V version) | VOUT | 4.96 | 5 | 5.04 | V | 0.1 mA < IOUT < 200 mA | 5 |
| Output voltage (5-V version) | VOUT | 4.91 | 5.09 | V | 0.1 mA < IOUT < 200 mA, -40°C ≤ TJ ≤ 125°C | 5 | |
| Output voltage line regulation | ΔVOUT/ΔVIN | 0.007 | 0.014 | %/V | VOUT(NOM) + 1 V ≤ VIN ≤ 16 V | 5 | |
| Output voltage line regulation | ΔVOUT/ΔVIN | 0.032 | %/V | VOUT(NOM) + 1 V ≤ VIN ≤ 16 V, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Dropout voltage | VIN, VOUT | 1 | 2 | mV | IOUT = 100 µA | 5 | |
| Dropout voltage | VIN, VOUT | 3.5 | mV | IOUT = 100 µA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Dropout voltage | VIN, VOUT | 90 | 120 | mV | IOUT = 75 mA | 5 | |
| Dropout voltage | VIN, VOUT | 170 | mV | IOUT = 75 mA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Dropout voltage | VIN, VOUT | 180 | 230 | mV | IOUT = 200 mA | 5 | |
| Dropout voltage | VIN, VOUT | 350 | mV | IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Ground pin current | IGND | 100 | 120 | µA | IOUT = 100 µA | 6 | |
| Ground pin current | IGND | 150 | µA | IOUT = 100 µA, -40°C ≤ TJ ≤ 125°C | 6 | ||
| Ground pin current | IGND | 500 | 800 | µA | IOUT = 75 mA | 6 | |
| Ground pin current | IGND | 1400 | µA | IOUT = 75 mA, -40°C ≤ TJ ≤ 125°C | 6 | ||
| Ground pin current | IGND | 1 | 2.1 | mA | IOUT = 200 mA | 6 | |
| Ground pin current | IGND | 3.7 | mA | IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C | 6 | ||
| Ground pin current in shutdown | IGND | 0.05 | µA | VSD < 0.3 V | 6 | ||
| Ground pin current in shutdown | IGND | 1.5 | µA | VSD < 0.3 V, -40°C ≤ TJ ≤ 125°C | 6 | ||
| Peak output current | IOUT(PK) | 250 | 400 | mA | VOUT ≥ VOUT(NOM) − 5% | 6 | |
| Short-circuit current | IOUT(MAX) | 400 | mA | RL = 0 (steady state) | 6 | ||
| Output noise voltage | en | 160 | µVRMS | BW = 300 Hz to 50 kHz, COUT = 10 µF | 6 | ||
| Ripple rejection | ΔVOUT/ΔVIN | 65 | dB | f = 1 kHz, COUT = 10 µF | 6 | ||
| Output voltage temperature coefficient | ΔVOUT/ΔTD | 20 | ppm/°C | See note (4) | 6 | ||
| FEEDBACK pin voltage | VFB | 1.21 | 1.23 | 1.25 | V | 6 | |
| FEEDBACK pin voltage | VFB | 1.2 | 1.26 | V | -40°C ≤ TJ ≤ 125°C | 6 | |
| FEEDBACK pin voltage | VFB | 1.19 | 1.28 | V | See note (5): VFB ≤ VOUT ≤ (VIN − 1), 2.5 V ≤ VIN ≤ 16 V, 100 µA ≤ IL ≤ 200 mA, TJ ≤ 125°C | 6 | |
| FEEDBACK pin voltage temperature coefficient | ΔVFB/ΔT | 20 | ppm/°C | See note (6) | 6 | ||
| FEEDBACK pin bias current | IFB | 150 | 330 | nA | IOUT = 200 mA | 6 | |
| FEEDBACK pin bias current | IFB | 760 | nA | IOUT = 200 mA, -40°C ≤ TJ ≤ 125°C | 6 | ||
| FEEDBACK pin bias current temperature coefficient | ΔIFB/ΔT | 0.1 | nA/°C | See note (6) | 6 | ||
| SHUTDOWN input voltage (output ON) | VH | 1.4 | V | VH = Output ON | 6 | ||
| SHUTDOWN input voltage (output ON) | VH | 1.6 | V | VH = Output ON, -40°C ≤ TJ ≤ 125°C | 6 | ||
| SHUTDOWN input voltage (output OFF) | VL | 0.55 | V | VL = Output OFF | 6 | ||
| SHUTDOWN input voltage (output OFF) | VL | 0.18 | V | VL = Output OFF, -40°C ≤ TJ ≤ 125°C | 6 | ||
| SHUTDOWN input current | ISD | 0 | µA | VSD = 0 V | 6 | ||
| SHUTDOWN input current | ISD | -1 | µA | VSD = 0 V, -40°C ≤ TJ ≤ 125°C | 6 | ||
| SHUTDOWN input current | ISD | 5 | µA | VSD = 5 V | 6 | ||
| SHUTDOWN input current | ISD | 15 | µA | VSD = 5 V, -40°C ≤ TJ ≤ 125°C | 6 | ||
| Output HIGH leakage current | IOH | 0.01 | 1 | µA | VOH = 16 V | 7 | |
| Output HIGH leakage current | IOH | 2 | µA | VOH = 16 V, -40°C ≤ TJ ≤ 125°C | 7 | ||
| ERROR comparator row (label not printed in extracted text) | 150 | 220 | µA | VIN = VOUT(NOM) − 0.5 V, IOUT(COMP) = 300 µA | 7 | ||
| Output LOW voltage (ERROR) | VOL | 350 | mV | VIN = VOUT(NOM) − 0.5 V, IOUT(COMP) = 300 µA | 7 | ||
| Upper threshold voltage | VTHR(MAX) | -5.5 | -4.6 | -3.5 | %VOUT | 7 | |
| Upper threshold voltage | VTHR(MAX) | -7.7 | -2.5 | %VOUT | -40°C ≤ TJ ≤ 125°C | 7 | |
| Lower threshold voltage | VTHR(MIN) | -8.9 | -6.6 | -4.9 | %VOUT | 7 | |
| Lower threshold voltage | VTHR(MIN) | -13 | -3.3 | %VOUT | -40°C ≤ TJ ≤ 125°C | 7 | |
| Hysteresis | HYST | 2 | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | capacitor, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side, copper surface. The use of vias and long traces to create LDO circuit connections is stron | 20 |
CAD (KiCad official)
- Symbol:
LP2986AIM-5.0 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
lp2986aim-5-0-etched.step/lp2986aim-5-0-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp2986aim-5-0.step/lp2986aim-5-0.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (38 pp, sha256
e7d8f233a69ce5e5, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).