3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32L432KCU6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-32(5x5)
STM32L432KCU6 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Main supply pin of the MCU, to be connected to the 1.71 V to 3.6 V external supply (Table 21 gives the standard operating voltage range). |
| 2 | PC14-OSC32_IN | bidirectional | GPIO FT I/O supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as driving an LED; also serves as the OSC32_IN LSE input. |
| 3 | PC15-OSC32_OUT | bidirectional | GPIO FT I/O supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as driving an LED; also serves as the OSC32_OUT LSE output. |
| 4 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 5 | VDDA/VREF+ | power_in | Analog supply pin and positive reference voltage input for the ADC, DAC, comparators and operational amplifier. |
| 6 | PA0/CK_IN | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM2_CH1, USART2_CTS and SAI1_EXTCLK, with additional functions OPAMP1_VINP, ADC1_IN5 and WKUP1. |
| 7 | PA1 | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM2_CH2, I2C1_SMBA and SPI1_SCK, with additional functions OPAMP1_VINM, COMP1_INP and ADC1_IN6. |
| 8 | PA2 | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM2_CH3, USART2_TX and LPUART1_TX, with additional functions COMP2_INM, ADC1_IN7 and WKUP4. |
| 9 | PA3 | bidirectional | TT_a I/O, 3.6 V tolerant; alternate functions include TIM2_CH4, USART2_RX and LPUART1_RX, with additional functions OPAMP1_VOUT, COMP2_INP and ADC1_IN8. |
| 10 | PA4 | bidirectional | TT_a I/O, 3.6 V tolerant; alternate functions include SPI1_NSS, SPI3_NSS and USART2_CK, with additional functions COMP1_INM, COMP2_INM, ADC1_IN9 and DAC1_OUT1. |
| 11 | PA5 | bidirectional | TT_a I/O, 3.6 V tolerant; alternate functions include TIM2_CH1, TIM2_ETR and SPI1_SCK, with additional functions COMP1_INM, COMP2_INM, ADC1_IN10 and DAC1_OUT2. |
| 12 | PA6 | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM1_BKIN, SPI1_MISO and USART3_CTS, with additional function ADC1_IN11. |
| 13 | PA7 | bidirectional | FT_fa I/O, 5 V tolerant and Fm+ capable; alternate functions include TIM1_CH1N, I2C3_SCL and SPI1_MOSI, with additional function ADC1_IN12. |
| 14 | PB0 | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM1_CH2N, SPI1_NSS and USART3_CK, with additional function ADC1_IN15. |
| 15 | PB1 | bidirectional | FT_a I/O, 5 V tolerant; alternate functions include TIM1_CH3N, USART3_RTS_DE and LPUART1_RTS_DE, with additional functions COMP1_INM and ADC1_IN16. |
| 16 | VSS | power_in | Ground pin, to be connected to the external ground. |
| 17 | VDD | power_in | Main supply pin of the MCU, to be connected to the external supply within the permitted range. |
| 18 | PA8 | bidirectional | FT I/O, 5 V tolerant; alternate functions include MCO, TIM1_CH1, USART1_CK and SAI1_SCK_A. |
| 19 | PA9 | bidirectional | FT_f I/O, 5 V tolerant and Fm+ capable; alternate functions include TIM1_CH2, I2C1_SCL and USART1_TX. |
| 20 | PA10 | bidirectional | FT_f I/O, 5 V tolerant and Fm+ capable; alternate functions include TIM1_CH3, I2C1_SDA, USART1_RX and USB_CRS_SYNC. |
| 21 | PA11 | bidirectional | FT_u I/O, 5 V tolerant, with USB function supplied by VDDUSB; alternate functions include TIM1_CH4, SPI1_MISO, CAN1_RX and USB_DM. |
| 22 | PA12 | bidirectional | FT_u I/O, 5 V tolerant, with USB function supplied by VDDUSB; alternate functions include TIM1_ETR, SPI1_MOSI, CAN1_TX and USB_DP. |
| 23 | PA13 | bidirectional | FT I/O, 5 V tolerant; after reset configured as JTMS-SWDIO debug function with internal pull-up activated. |
| 24 | PA14 | bidirectional | FT I/O, 5 V tolerant; after reset configured as JTCK-SWCLK debug function with internal pull-down activated. |
| 25 | PA15 | bidirectional | FT I/O, 5 V tolerant; after reset configured as JTDI debug function with internal pull-up activated. |
| 26 | PB3 | bidirectional | FT_a I/O, 5 V tolerant; after reset configured as JTDO-TRACESWO debug function; alternate functions include TIM2_CH2, SPI1_SCK and SAI1_SCK_B. |
| 27 | PB4 | bidirectional | FT_fa I/O, 5 V tolerant and Fm+ capable; after reset configured as NJTRST debug function with internal pull-up activated; additional function COMP2_INP. |
| 28 | PB5 | bidirectional | FT I/O, 5 V tolerant; alternate functions include LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI and COMP2_OUT. |
| 29 | PB6 | bidirectional | FT_fa I/O, 5 V tolerant and Fm+ capable; alternate functions include LPTIM1_ETR, I2C1_SCL and USART1_TX, with additional function COMP2_INP. |
| 30 | PB7 | bidirectional | FT_fa I/O, 5 V tolerant and Fm+ capable; alternate functions include LPTIM1_IN2, I2C1_SDA and USART1_RX, with additional functions COMP2_INM and PVD_IN. |
| 31 | PH3/BOOT0 | bidirectional | FT I/O, 5 V tolerant; also serves as the BOOT0 boot configuration input. |
| 32 | VSS | power_in | Ground pin, to be connected to the external ground. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage ratings VDDX - VSS | VDDX - VSS | -0.3 | 4 | V | 65 | ||
| Total current into sum of VDD power lines | ∑IVDD | 140 | mA | Source current | 66 | ||
| Maximum current into each VDD power pin | IVDD(PIN) | 100 | mA | Source current | 66 | ||
| Maximum current out of each VSS ground pin | IVSS(PIN) | 100 | mA | Sink current | 66 | ||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 66 | |||
| Injected current on FT, TT, RST and B pins | IINJ(PIN) | -5 | 0 | mA | Except PA4, PA5 | 66 | |
| Total injected current, sum of all I/Os and control pins | ∑/IINJ(PIN)/ | 25 | mA | 66 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 66 | ||
| Maximum junction temperature | TJ | 150 | °C | 66 | |||
| Internal AHB clock frequency | fHCLK | 0 | 80 | MHz | 67 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 67 | ||
| Analog supply voltage, ADC or COMP used | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 67 | |
| Analog supply voltage, DAC or OPAMP used | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 67 | |
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 67 | |
| Ambient temperature, suffix 6 version, maximum power dissipation | TA | -40 | 85 | °C | Maximum power dissipation | 67 | |
| Ambient temperature, suffix 6 version, low-power dissipation | TA | -40 | 105 | °C | Low-power dissipation | 67 | |
| Power dissipation, suffix 6 | PD | 523 | mW | TA = 85 °C for suffix 6 | 67 | ||
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 67 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 68 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 68 |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 68 | |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 70 |
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 70 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 70 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C | 70 | |
| Supply current in Run mode, Range 1, 80 MHz | IDD_ALL (Run) | 8.53 | 9.5 | mA | Range 1, fHCLK 80 MHz, all peripherals disabled, 25 °C | 73 | |
| Supply current in Stop 2 mode, RTC disabled | IDD_ALL (Stop 2) | 1.06 | 2.1 | µA | VDD 3 V, 25 °C | 79 | |
| Supply current in Stop 1 mode, RTC disabled | IDD_ALL (Stop 1) | 4.41 | 9.5 | µA | VDD 3 V, 25 °C | 81 | |
| Supply current in Stop 0 mode, RTC disabled | IDD_ALL (Stop 0) | 111 | 139 | µA | VDD 3 V, 25 °C | 82 | |
| Supply current in Standby mode, RTC disabled | IDD_ALL (Standby) | 90.2 | 225 | nA | No independent watchdog, VDD 3 V, 25 °C | 83 | |
| Supply current in Shutdown mode, RTC disabled | IDD_ALL (Shutdown) | 44.3 | 70.1 | nA | VDD 3 V, 25 °C | 84 | |
| High-speed external user clock frequency, Range 1 | fHSE_ext | 8 | 48 | MHz | Voltage scaling Range 1 | 92 | |
| High-speed external user clock frequency, Range 2 | fHSE_ext | 8 | 26 | MHz | Voltage scaling Range 2 | 92 | |
| CK_IN high or low time, Range 1 | tw(HSEH) tw(HSEL) | 7 | ns | Voltage scaling Range 1 | 92 | ||
| CK_IN high or low time, Range 2 | tw(HSEH) tw(HSEL) | 18 | ns | Voltage scaling Range 2 | 92 | ||
| Low-speed external user clock frequency | fLSE_ext | 32.768 | 1000 | kHz | 93 | ||
| OSC32_IN high or low time | tw(LSEH) tw(LSEL) | 250 | ns | 93 | |||
| HSI16 frequency | fHSI16 | 15.88 | 16.08 | MHz | VDD=3.0 V, TA=30 °C | 95 | |
| HSI16 user trimming step, code not multiple of 64 | TRIM | 0.2 | 0.3 | 0.4 | % | Trimming code is not a multiple of 64 | 95 |
| HSI16 frequency drift over temperature, TA 0 to 85 °C | ∆Temp(HSI16) | -1 | 1 | % | TA = 0 to 85 °C | 95 | |
| HSI16 frequency drift over temperature, TA -40 to 125 °C | ∆Temp(HSI16) | -2 | 1.5 | % | TA = -40 to 125 °C | 95 | |
| HSI16 frequency drift over VDD | ∆VDD(HSI16) | -0.1 | 0.05 | % | VDD=1.62 V to 3.6 V | 95 | |
| MSI frequency after factory calibration, Range 11 | fMSI | 47.38 | 48 | 48.62 | MHz | MSI mode, VDD=3 V, TA=30 °C | 97 |
| MSI oscillator frequency drift over temperature, TA 0 to 85 °C | ∆TEMP(MSI) | -3.5 | 3 | % | MSI mode, TA = -0 to 85 °C | 97 | |
| MSI oscillator frequency drift over temperature, TA -40 to 125 °C | ∆TEMP(MSI) | -8 | 6 | % | MSI mode, TA = -40 to 125 °C | 97 | |
| HSI48 accuracy over temperature, VDD 3.0 to 3.6 V | ACCHSI48_REL | -3 | 3 | % | VDD = 3.0 V to 3.6 V, TA = -15 to 85 °C | 100 | |
| HSI48 accuracy over temperature, VDD 1.65 to 3.6 V | ACCHSI48_REL | -4.5 | 4.5 | % | VDD = 1.65 V to 3.6 V, TA = -40 to 125 °C | 100 | |
| LSI frequency at 3.0 V, 30 °C | fLSI | 31.04 | 32.96 | kHz | VDD = 3.0 V, TA = 30 °C | 101 | |
| LSI frequency over supply and temperature | fLSI | 29.5 | 34 | kHz | VDD = 1.62 to 3.6 V, TA = -40 to 125 °C | 101 |
CAD (KiCad official)
- Symbol:
STM32L432KCU6 - Footprint:
Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm - 3D model: UFQFPN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
stm32l432kcu6-etched.step/stm32l432kcu6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l432kcu6.step/stm32l432kcu6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (156 pp, sha256
411517499bfbb10c, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).