3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8618CAV#TRPBF
Analog Devices Inc. · AC-DC Controllers & Regulators · LQFN-12(2x2)
LT8618CAV#TRPBF from Analog Devices Inc., in a LQFN-12(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Supplies current to the LT8618C internal circuitry and the internal top-side power switch; operating input is 3.4V to 60V with 65V maximum for transients, and the input capacitor positive terminal should be placed as close as possible to this pin. |
| 2 | EN/UV | input | Enable pin: the LT8618C is shut down when low and active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it can be tied to VIN if shutdown is not used. |
| 3 | HYST | output | Open-drain EN/UV hysteresis logic output that is pulled to ground when EN/UV is below 1V, used to adjust EN/UV pin hysteresis; absolute maximum voltage is 12V. |
| 4 | PG | output | Open-drain power-good output that stays low until FB is within ±7.5% of the final regulation voltage with no fault conditions, is valid when VIN is above 3.4V, and has a 42V maximum voltage rating. |
| 5 | FB | input | Feedback pin that the LT8618C regulates to 0.778V; the feedback resistor divider tap connects here, with an absolute maximum voltage of 4V. |
| 6 | TR/SS | bidirectional | Output tracking and soft-start pin: a voltage below 0.778V forces FB to follow TR/SS, an internal 2µA pull-up sets the soft-start slew rate, and a 300Ω pull-down acts during shutdown and faults, so use a series resistor when driven from a low-impedance source; absolute maximum voltage is 4V. |
| 7 | SYNC/MODE | input | Mode-select pin: tie low for Burst Mode operation, float for forced continuous mode (leakage below 1µA), tie above 3V for spread-spectrum mode, or drive with a clock (valleys below 0.4V, peaks above 1.5V up to 6V) to synchronize over 200kHz to 2.2MHz. |
| 8 | RT | passive | Tie a resistor between this pin and ground to set the switching frequency over the 200kHz to 2.2MHz range. |
| 9 | BIAS | power_in | Supplies the internal regulator when tied above 3.2V; for output voltages of 3.3V to 25V it should be tied to VOUT, a 1µF local bypass is required if another supply is used, and it should be tied to GND if no supply is available. |
| 10 | SW | output | Output of the internal power switches that connects to the inductor; this node should be kept small on the PCB for good performance. |
| 11 | DNC | unconnected | Do not connect; this pin must be left floating. |
| 12 | GND | power_in | Ground pin that should be connected to the input capacitor negative terminal, placed as close as possible to the VIN capacitor. |
| 13 | GND | power_in | Exposed pad ground that must be connected to the input capacitor negative terminal and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc. |
| Package | LQFN-12(2x2) |
| Category | Power Management ICs |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | 3.4 | 60 | V | 3 | |||
| Oscillator Frequency | 140 | 200 | 260 | kHz | RT = 221k | 3 | |
| Oscillator Frequency | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, LT8618/LT8618-3.3/LT8618C | 3 | |
| LT8618/LT8618C Feedback Reference Voltage | 0.762 | 0.778 | 0.798 | V | VIN = 12V, ILOAD = 100µA | 3 | |
| FB/OUT Voltage Line Regulation | -0.06 | 0.02 | 0.06 | %/V | VIN = 4V to 60V | 3 | |
| LT8618/LT8618C FB Pin Input Current | -20 | 20 | nA | VFB = 0.8V | 3 | ||
| Minimum On-Time | 35 | 65 | ns | 3 | |||
| Minimum Off-Time | 90 | 120 | ns | 3 | |||
| Top Power NMOS Current Limit | 150 | 200 | 250 | mA | 3 | ||
| SW Leakage Current | 15 | µA | VIN = 48V | 3 | |||
| EN/UV Pin Threshold Voltage | 0.98 | 1.05 | 1.11 | V | Pin Voltage Rising | 3 | |
| EN/UV Pin Current | -50 | 50 | nA | VEN/UV = 2V | 3 | ||
| HYST Pull-Down Resistance | 280 | 500 | Ω | VHYST = 0.1V, VEN/UV < 0.9V, LT8618C Only | 3 | ||
| HYST Pin Leakage Current | -200 | 200 | nA | VHYST = 1V, VEN/UV > 1.2V, LT8618C Only | 3 | ||
| PG Upper Threshold Offset from VFB/OUT | 4.5 | 7.5 | 10 | % | VFB/OUT Rising, LT8618C/LT8618A-3.3/5 | 4 | |
| PG Lower Threshold Offset from VFB/OUT | -10 | -7.5 | -5 | % | VFB/OUT Falling, LT8618/LT8618-3.3/LT8618C | 4 | |
| PG Leakage | -200 | 200 | nA | VPG = 42V | 4 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 4 | ||
| SYNC/MODE Threshold Voltage | 0.4 | 0.9 | 1.5 | V | LT8618C Only | 4 | |
| TR/SS Source Current | 1 | 2 | 4 | µA | VTR/SS = 0.1V, J-, A-, and R-Grades | 4 | |
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, VTR/SS = 0.1V | 4 | ||
| VIN to Disable Forced Continuous Mode | 30 | 32 | 34 | V | VIN Rising, LT8618C Only | 4 | |
| VIN Quiescent Current | 1 | 4 | µA | VEN/UV = 0V | 3 | ||
| VIN Quiescent Current | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching | 3 | ||
| VIN Current in Regulation | 56 | µA | VIN = 12V, VOUT = 3.3V, ILOAD = 100µA | 3 | |||
| VIN Current in Regulation | 400 | µA | VIN = 12V, VOUT = 3.3V, ILOAD = 1mA | 3 | |||
| BIAS Pin Current Consumption | 0.8 | mA | VBIAS = 3.3V, ILOAD = 30mA, 700kHz | 3 | |||
| Top Power NMOS On-Resistance | 3 | Ω | 3 | ||||
| Bottom Power NMOS On-Resistance | 1.3 | Ω | 3 | ||||
| EN/UV Pin Hysteresis | 50 | mV | 3 | ||||
| PG Hysteresis | 0.5 | % | 4 | ||||
| VIN, EN/UV Voltage | -0.3 | 65 | V | Note 4: 65V transients, 60V continuous | 2 | ||
| PG Voltage | -0.3 | 42 | V | 2 | |||
| BIAS Voltage | -0.3 | 25 | V | 2 | |||
| HYST Voltage | -0.3 | 12 | V | LT8618C Only | 2 | ||
| FB Voltage | -0.3 | 4 | V | FB (LT8618/LT8618C) | 2 | ||
| TR/SS Voltage | -0.3 | 4 | V | 2 | |||
| SYNC/MODE Voltage | -0.3 | 6 | V | LT8618C Only | 2 | ||
| Operating Junction Temperature Range | -40 | 125 | °C | LT8618CA | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 51 | °C/W | 12-lead LQFN (2mm x 2mm) | 2 | ||
| Maximum Junction Temperature | TJMAX | 125 | °C | 12-lead LQFN (2mm x 2mm) | 2 |
CAD (KiCad official)
- Symbol:
LT8618CAV#TRPBF - Footprint:
Package_DFN_QFN:LQFN-12-1EP_2x2mm_P0.5mm_EP0.7x0.7mm - 3D model: LQFN-12(2x2), generated on the KiCad land (body 2 x 2 mm, terminals on the pads, 0.9 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lt8618cav-etched.step/lt8618cav-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8618cav.step/lt8618cav.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc. datasheet (29 pp, sha256
4bd6ffbba1021846, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).