Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8618CAV#TRPBF

Analog Devices Inc. · AC-DC Controllers & Regulators · LQFN-12(2x2)

LT8618CAV#TRPBF from Analog Devices Inc., in a LQFN-12(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Supplies current to the LT8618C internal circuitry and the internal top-side power switch; operating input is 3.4V to 60V with 65V maximum for transients, and the input capacitor positive terminal should be placed as close as possible to this pin.
2 EN/UV input Enable pin: the LT8618C is shut down when low and active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it can be tied to VIN if shutdown is not used.
3 HYST output Open-drain EN/UV hysteresis logic output that is pulled to ground when EN/UV is below 1V, used to adjust EN/UV pin hysteresis; absolute maximum voltage is 12V.
4 PG output Open-drain power-good output that stays low until FB is within ±7.5% of the final regulation voltage with no fault conditions, is valid when VIN is above 3.4V, and has a 42V maximum voltage rating.
5 FB input Feedback pin that the LT8618C regulates to 0.778V; the feedback resistor divider tap connects here, with an absolute maximum voltage of 4V.
6 TR/SS bidirectional Output tracking and soft-start pin: a voltage below 0.778V forces FB to follow TR/SS, an internal 2µA pull-up sets the soft-start slew rate, and a 300Ω pull-down acts during shutdown and faults, so use a series resistor when driven from a low-impedance source; absolute maximum voltage is 4V.
7 SYNC/MODE input Mode-select pin: tie low for Burst Mode operation, float for forced continuous mode (leakage below 1µA), tie above 3V for spread-spectrum mode, or drive with a clock (valleys below 0.4V, peaks above 1.5V up to 6V) to synchronize over 200kHz to 2.2MHz.
8 RT passive Tie a resistor between this pin and ground to set the switching frequency over the 200kHz to 2.2MHz range.
9 BIAS power_in Supplies the internal regulator when tied above 3.2V; for output voltages of 3.3V to 25V it should be tied to VOUT, a 1µF local bypass is required if another supply is used, and it should be tied to GND if no supply is available.
10 SW output Output of the internal power switches that connects to the inductor; this node should be kept small on the PCB for good performance.
11 DNC unconnected Do not connect; this pin must be left floating.
12 GND power_in Ground pin that should be connected to the input capacitor negative terminal, placed as close as possible to the VIN capacitor.
13 GND power_in Exposed pad ground that must be connected to the input capacitor negative terminal and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices Inc.
Package LQFN-12(2x2)
Category Power Management ICs
Pins 13

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Input Voltage 3.4 60 V 3
Oscillator Frequency 140 200 260 kHz RT = 221k 3
Oscillator Frequency 1.85 2 2.15 MHz RT = 18.2k, LT8618/LT8618-3.3/LT8618C 3
LT8618/LT8618C Feedback Reference Voltage 0.762 0.778 0.798 V VIN = 12V, ILOAD = 100µA 3
FB/OUT Voltage Line Regulation -0.06 0.02 0.06 %/V VIN = 4V to 60V 3
LT8618/LT8618C FB Pin Input Current -20 20 nA VFB = 0.8V 3
Minimum On-Time 35 65 ns 3
Minimum Off-Time 90 120 ns 3
Top Power NMOS Current Limit 150 200 250 mA 3
SW Leakage Current 15 µA VIN = 48V 3
EN/UV Pin Threshold Voltage 0.98 1.05 1.11 V Pin Voltage Rising 3
EN/UV Pin Current -50 50 nA VEN/UV = 2V 3
HYST Pull-Down Resistance 280 500 Ω VHYST = 0.1V, VEN/UV < 0.9V, LT8618C Only 3
HYST Pin Leakage Current -200 200 nA VHYST = 1V, VEN/UV > 1.2V, LT8618C Only 3
PG Upper Threshold Offset from VFB/OUT 4.5 7.5 10 % VFB/OUT Rising, LT8618C/LT8618A-3.3/5 4
PG Lower Threshold Offset from VFB/OUT -10 -7.5 -5 % VFB/OUT Falling, LT8618/LT8618-3.3/LT8618C 4
PG Leakage -200 200 nA VPG = 42V 4
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 4
SYNC/MODE Threshold Voltage 0.4 0.9 1.5 V LT8618C Only 4
TR/SS Source Current 1 2 4 µA VTR/SS = 0.1V, J-, A-, and R-Grades 4
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, VTR/SS = 0.1V 4
VIN to Disable Forced Continuous Mode 30 32 34 V VIN Rising, LT8618C Only 4
VIN Quiescent Current 1 4 µA VEN/UV = 0V 3
VIN Quiescent Current 1.7 12 µA VEN/UV = 2V, Not Switching 3
VIN Current in Regulation 56 µA VIN = 12V, VOUT = 3.3V, ILOAD = 100µA 3
VIN Current in Regulation 400 µA VIN = 12V, VOUT = 3.3V, ILOAD = 1mA 3
BIAS Pin Current Consumption 0.8 mA VBIAS = 3.3V, ILOAD = 30mA, 700kHz 3
Top Power NMOS On-Resistance 3 Ω 3
Bottom Power NMOS On-Resistance 1.3 Ω 3
EN/UV Pin Hysteresis 50 mV 3
PG Hysteresis 0.5 % 4
VIN, EN/UV Voltage -0.3 65 V Note 4: 65V transients, 60V continuous 2
PG Voltage -0.3 42 V 2
BIAS Voltage -0.3 25 V 2
HYST Voltage -0.3 12 V LT8618C Only 2
FB Voltage -0.3 4 V FB (LT8618/LT8618C) 2
TR/SS Voltage -0.3 4 V 2
SYNC/MODE Voltage -0.3 6 V LT8618C Only 2
Operating Junction Temperature Range -40 125 °C LT8618CA 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient θJA 51 °C/W 12-lead LQFN (2mm x 2mm) 2
Maximum Junction Temperature TJMAX 125 °C 12-lead LQFN (2mm x 2mm) 2

CAD (KiCad official)

  • Symbol: LT8618CAV#TRPBF
  • Footprint: Package_DFN_QFN:LQFN-12-1EP_2x2mm_P0.5mm_EP0.7x0.7mm
  • 3D model: LQFN-12(2x2), generated on the KiCad land (body 2 x 2 mm, terminals on the pads, 0.9 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: lt8618cav-etched.step / lt8618cav-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8618cav.step / lt8618cav.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices Inc. datasheet (29 pp, sha256 4bd6ffbba1021846, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF