Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

F280034PTRQ1

Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)

F280034PTRQ1 from Texas Instruments, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GPIO29 bidirectional General-purpose I/O 29 with SCIA_TX, EPWM7_B, OUTPUTXBAR6 and AUXCLKIN alternate functions; GPIO input at reset with pull-up disabled.
2 GPIO28 bidirectional General-purpose I/O 28 with SCIA_RX, EPWM7_A and ERRORSTS alternate functions; GPIO input at reset with pull-up disabled.
3 XRSn bidirectional Device reset input and watchdog reset output, open-drain with internal pull-up; a 2.2 kΩ to 10 kΩ resistor to VDDIO is recommended and any capacitor to VSS should be 100 nF or less.
4 A6,B2,C6 input ADC-A input 6 shared with ADC-B input 2 and ADC-C input 6; analog input must stay below VDDA + 0.3 V.
5 A3,B3,C5,VDAC input ADC-A input 3 shared with ADC-B input 3, ADC-C input 5 and optional external DAC reference VDAC; at least 1 µF on VDAC when used as the DAC reference.
6 A2,B6,C9 input ADC-A input 2 shared with ADC-B input 6 and ADC-C input 9; analog input must stay below VDDA + 0.3 V.
7 A15,B9,C7 input ADC-A input 15 shared with ADC-B input 9 and ADC-C input 7; analog input must stay below VDDA + 0.3 V.
8 A11,B10,C0 input ADC-A input 11 shared with ADC-B input 10 and ADC-C input 0; analog input must stay below VDDA + 0.3 V.
9 A5,B12,C2 input ADC-A input 5 shared with ADC-B input 12 and ADC-C input 2; analog input must stay below VDDA + 0.3 V.
10 A1,B7,DACB_OUT passive ADC-A input 1 shared with ADC-B input 7 and buffered DAC-B output; unused analog pin may be left unconnected or tied to VSSA through 4.7 kΩ or greater.
11 A0,B15,C15,DACA_OUT passive ADC-A input 0 shared with ADC-B input 15, ADC-C input 15 and buffered DAC-A output.
12 VREFHI input ADC high reference voltage; at least one 2.2 µF capacitor between VREFHI and VREFLO placed as close to the device as possible.
13 VREFLO input ADC low reference voltage, connected to VSSA.
14 A12,C1 input ADC-A input 12 shared with ADC-C input 1; analog input must stay below VDDA + 0.3 V.
15 A7,C3 input ADC-A input 7 shared with ADC-C input 3; analog input must stay below VDDA + 0.3 V.
16 A8,B0,C11 input ADC-A input 8 shared with ADC-B input 0 and ADC-C input 11; analog input must stay below VDDA + 0.3 V.
17 VSSA power_in Analog ground.
18 VDDA power_in 3.3 V analog supply; a decoupling capacitor of at least 2.2 µF is required on this pin.
19 A4,B8,C14 input ADC-A input 4 shared with ADC-B input 8 and ADC-C input 14; analog input must stay below VDDA + 0.3 V.
20 A9,B4,C8 input ADC-A input 9 shared with ADC-B input 4 and ADC-C input 8; analog input must stay below VDDA + 0.3 V.
21 A10,B1,C10 input ADC-A input 10 shared with ADC-B input 1 and ADC-C input 10; analog input must stay below VDDA + 0.3 V.
22 VSS power_in Digital ground; all VSS pins must be connected to the board ground.
23 VDD power_in 1.2 V digital logic supply; decoupling capacitors are required on VDD even when the internal VREG is used.
24 VDDIO power_in 3.3 V digital I/O supply.
25 GPIO33 bidirectional General-purpose I/O 33 with I2CA_SCL, SPIB_STE, LINA_RX and ADCSOCAO alternate functions.
26 GPIO16 bidirectional General-purpose I/O 16 with SPIA_SIMO, EPWM5_A, SCIA_TX and XCLKOUT alternate functions.
27 GPIO24 bidirectional General-purpose I/O 24 with OUTPUTXBAR1, EPWM8_A, SCIA_TX and ERRORSTS alternate functions; the ERRORSTS output requires an external pull-down resistor.
28 TCK input JTAG test clock input with internal pull-up.
29 GPIO37/TDO output JTAG test data output (default function) shared with GPIO37; TDO is tri-stated when JTAG is inactive, so an internal or external pull-up must be used.
30 TMS bidirectional JTAG test mode select with internal pull-up; a 2.2 kΩ external pull-up to VDDIO is recommended.
31 GPIO35/TDI input JTAG test data input (default function) shared with GPIO35; enable the internal pull-up or add an external pull-up to avoid a floating input.
32 GPIO32 bidirectional General-purpose I/O 32 with I2CA_SDA, SPIB_CLK, EPWM8_B and ADCSOCBO alternate functions.
33 GPIO18/X2 bidirectional General-purpose I/O 18, or crystal oscillator output X2 when the crystal oscillator is enabled.
34 GPIO19/X1 bidirectional General-purpose I/O 19, or crystal oscillator / single-ended clock input X1; initialization software must configure this pin before enabling the crystal oscillator.
35 VDDIO power_in 3.3 V digital I/O supply.
36 VDD power_in 1.2 V digital logic supply; decoupling capacitors are required.
37 VSS power_in Digital ground; must be connected to the board ground.
38 GPIO4 bidirectional General-purpose I/O 4 with EPWM3_A, MCAN_TX, CANA_TX and HIC_NWE alternate functions.
39 GPIO3 bidirectional General-purpose I/O 3 with EPWM2_B, PMBUSA_SCL, SCIA_RX and CANA_RX alternate functions.
40 GPIO2 bidirectional General-purpose I/O 2 with EPWM2_A, PMBUSA_SDA, SCIA_TX and CANA_TX alternate functions.
41 GPIO1 bidirectional General-purpose I/O 1 with EPWM1_B, I2CA_SCL, MCAN_TX and FSITXA_TDM_D1 alternate functions.
42 GPIO0 bidirectional General-purpose I/O 0 with EPWM1_A, I2CA_SDA, MCAN_RX and EQEP1_INDEX alternate functions.
43 GPIO7 bidirectional General-purpose I/O 7 with EPWM4_B, EQEP1_B, SPIB_SIMO and FSITXA_CLK alternate functions.
44 VSS power_in Digital ground; must be connected to the board ground.
45 VDD power_in 1.2 V digital logic supply; decoupling capacitors are required.
46 VDDIO power_in 3.3 V digital I/O supply.
47 GPIO5 bidirectional General-purpose I/O 5 with EPWM3_B, OUTPUTXBAR3, MCAN_RX and CANA_RX alternate functions.
48 GPIO6 bidirectional General-purpose I/O 6 with EPWM4_A, OUTPUTXBAR4, SYNCOUT and EQEP1_A alternate functions.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package LQFP-48(7x7)
Category Embedded Processors & Controllers
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Low-level output voltage VOL 0.4 V IOL = IOL max 71
Low-level output voltage VOL 0.2 V IOL = 100µA 71
High-level output impedance, all output pins ROH 50 66 96 Ω VOH=VDDIO-0.4V 71
Low-level output impedance, all output pins ROL 48 60 84 Ω VOL = 0.4V 71
High-level input voltage VIH 2 V 71
Low-level input voltage VIL 0.8 V 71
Weak pull-down resistance RPULLDOWN 22 31 62 kΩ 71
Weak pull-up resistance RPULLUP 19 30 54 kΩ 71
Internal regulator output VVREG 1.14 1.2 1.32 V 83
VDDIO supply ramp-up rate SRVDDIO-UP 8 100 mV/μs 3.3V rail (VDDIO) 83
VDDIO supply ramp-down rate SRVDDIO-DN 20 100 mV/μs 3.3V rail (VDDIO) 83
VDD supply ramp-up rate SRVDD-UP 3.5 100 mV/μs 1.2V rail (VDD) 83
VDD supply ramp-down rate SRVDD-DN 10 100 mV/μs 1.2V rail (VDD) 83
Crystal load capacitance CL1, CL2 12 24 pF 98
Crystal shunt capacitance C0 7 pF 98
INTOSC1/INTOSC2 frequency fINTOSC 9.82 10 10.1 MHz -40℃ to 125℃ 100
INTOSC1/INTOSC2 frequency fINTOSC 9.86 10 10.1 MHz -30℃ to 90℃ 100
INTOSC1/INTOSC2 frequency fINTOSC 9.9 10 10.1 MHz -10℃ to 85℃ 100
INTOSC frequency stability at room temperature fINTOSC-STABILITY -0.1 0.1 % 30°C, nominal VDD 100
CMPSS comparator hysteresis 1x 4 12 20 LSB 141
CMPSS comparator hysteresis 2x 17 24 33 LSB 141
CMPSS comparator hysteresis 3x 25 36 50 LSB 141
CMPSS comparator hysteresis 4x 30 48 67 LSB 141
CMPSS comparator input-referred offset voltage error -20 20 mV Low common mode, inverting input set to 50mV 141
CMPSS DAC static offset voltage error -25 25 mV 142
CMPSS DAC static gain error -2 2 FSR 百分比 142
CMPSS DAC static DNL -1 4 LSB corrected endpoints 142
CMPSS DAC static INL -16 16 LSB corrected endpoints 142
Buffered DAC offset error -10 10 mV midpoint 146
Buffered DAC gain error -2.5 2.5 FSR 百分比 146
Buffered DAC differential nonlinearity DNL -1 1 LSB corrected endpoints 146
Buffered DAC integral nonlinearity INL -5 5 LSB corrected endpoints 146
PMBus input voltage low VIL 0.8 V 171
PMBus input voltage high VIH 2.1 V 171
PMBus low-level output voltage VOL 0.4 V Ipullup = 4mA 171
PMBus spike pulse width suppressed by input filter tSP 0 50 ns 171
PMBus input leakage current per pin Ii -10 10 µA 0.1Vbus < Vi < 0.9Vbus 171
PMBus fast mode SCL clock frequency fSCL 10 400 kHz 171
PMBus fast mode bus free time between stop and start tBUF 1.3 µs 171
PMBus fast mode start condition hold time tHD;STA 0.6 µs 171
PMBus fast mode repeated start setup time tSU;STA 0.6 µs 171
PMBus fast mode stop condition setup time tSU;STO 0.6 µs 171
PMBus fast mode data hold time after SCL falling tHD;DAT 300 ns 171
PMBus fast mode data setup time before SCL rising tSU;DAT 100 ns 171
PMBus fast mode SCL low period tLOW 1.3 µs 171
PMBus fast mode SCL high period tHIGH 0.6 50 µs 171
PMBus fast mode SDA and SCL rise time tr 20 300 ns 5% to 95% 171
PMBus fast mode SDA and SCL fall time tf 20 300 ns 95% to 5% 171
PMBus standard mode SCL clock frequency fSCL 10 100 kHz 172
PMBus standard mode bus free time between stop and start tBUF 4.7 µs 172
PMBus standard mode start condition hold time tHD;STA 4 µs 172
PMBus standard mode repeated start setup time tSU;STA 4.7 µs 172
PMBus standard mode stop condition setup time tSU;STO 4 µs 172
PMBus standard mode data hold time after SCL falling tHD;DAT 300 ns 172
PMBus standard mode data setup time before SCL rising tSU;DAT 250 ns 172
PMBus standard mode SCL low period tLOW 4.7 µs 172
PMBus standard mode SCL high period tHIGH 4 50 µs 172
PMBus standard mode SDA and SCL rise time tr 1000 ns 172
PMBus standard mode SDA and SCL fall time tf 300 ns 172

CAD (KiCad official)

  • Symbol: F280034PTRQ1
  • Footprint: Package_QFP:LQFP-48_7x7mm_P0.5mm
  • 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: f280034ptrq1-etched.step / f280034ptrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); f280034ptrq1.step / f280034ptrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (285 pp, sha256 4385cb7a74ef5d7f, retrieved 2026-11-02, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF