component
F280034PTRQ1
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
F280034PTRQ1
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
F280034PTRQ1 from Texas Instruments, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with SCIA_TX, EPWM7_B, OUTPUTXBAR6 and AUXCLKIN alternate functions; GPIO input at reset with pull-up disabled. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with SCIA_RX, EPWM7_A and ERRORSTS alternate functions; GPIO input at reset with pull-up disabled. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output, open-drain with internal pull-up; a 2.2 kΩ to 10 kΩ resistor to VDDIO is recommended and any capacitor to VSS should be 100 nF or less. |
| 4 | A6,B2,C6 | input | ADC-A input 6 shared with ADC-B input 2 and ADC-C input 6; analog input must stay below VDDA + 0.3 V. |
| 5 | A3,B3,C5,VDAC | input | ADC-A input 3 shared with ADC-B input 3, ADC-C input 5 and optional external DAC reference VDAC; at least 1 µF on VDAC when used as the DAC reference. |
| 6 | A2,B6,C9 | input | ADC-A input 2 shared with ADC-B input 6 and ADC-C input 9; analog input must stay below VDDA + 0.3 V. |
| 7 | A15,B9,C7 | input | ADC-A input 15 shared with ADC-B input 9 and ADC-C input 7; analog input must stay below VDDA + 0.3 V. |
| 8 | A11,B10,C0 | input | ADC-A input 11 shared with ADC-B input 10 and ADC-C input 0; analog input must stay below VDDA + 0.3 V. |
| 9 | A5,B12,C2 | input | ADC-A input 5 shared with ADC-B input 12 and ADC-C input 2; analog input must stay below VDDA + 0.3 V. |
| 10 | A1,B7,DACB_OUT | passive | ADC-A input 1 shared with ADC-B input 7 and buffered DAC-B output; unused analog pin may be left unconnected or tied to VSSA through 4.7 kΩ or greater. |
| 11 | A0,B15,C15,DACA_OUT | passive | ADC-A input 0 shared with ADC-B input 15, ADC-C input 15 and buffered DAC-A output. |
| 12 | VREFHI | input | ADC high reference voltage; at least one 2.2 µF capacitor between VREFHI and VREFLO placed as close to the device as possible. |
| 13 | VREFLO | input | ADC low reference voltage, connected to VSSA. |
| 14 | A12,C1 | input | ADC-A input 12 shared with ADC-C input 1; analog input must stay below VDDA + 0.3 V. |
| 15 | A7,C3 | input | ADC-A input 7 shared with ADC-C input 3; analog input must stay below VDDA + 0.3 V. |
| 16 | A8,B0,C11 | input | ADC-A input 8 shared with ADC-B input 0 and ADC-C input 11; analog input must stay below VDDA + 0.3 V. |
| 17 | VSSA | power_in | Analog ground. |
| 18 | VDDA | power_in | 3.3 V analog supply; a decoupling capacitor of at least 2.2 µF is required on this pin. |
| 19 | A4,B8,C14 | input | ADC-A input 4 shared with ADC-B input 8 and ADC-C input 14; analog input must stay below VDDA + 0.3 V. |
| 20 | A9,B4,C8 | input | ADC-A input 9 shared with ADC-B input 4 and ADC-C input 8; analog input must stay below VDDA + 0.3 V. |
| 21 | A10,B1,C10 | input | ADC-A input 10 shared with ADC-B input 1 and ADC-C input 10; analog input must stay below VDDA + 0.3 V. |
| 22 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 23 | VDD | power_in | 1.2 V digital logic supply; decoupling capacitors are required on VDD even when the internal VREG is used. |
| 24 | VDDIO | power_in | 3.3 V digital I/O supply. |
| 25 | GPIO33 | bidirectional | General-purpose I/O 33 with I2CA_SCL, SPIB_STE, LINA_RX and ADCSOCAO alternate functions. |
| 26 | GPIO16 | bidirectional | General-purpose I/O 16 with SPIA_SIMO, EPWM5_A, SCIA_TX and XCLKOUT alternate functions. |
| 27 | GPIO24 | bidirectional | General-purpose I/O 24 with OUTPUTXBAR1, EPWM8_A, SCIA_TX and ERRORSTS alternate functions; the ERRORSTS output requires an external pull-down resistor. |
| 28 | TCK | input | JTAG test clock input with internal pull-up. |
| 29 | GPIO37/TDO | output | JTAG test data output (default function) shared with GPIO37; TDO is tri-stated when JTAG is inactive, so an internal or external pull-up must be used. |
| 30 | TMS | bidirectional | JTAG test mode select with internal pull-up; a 2.2 kΩ external pull-up to VDDIO is recommended. |
| 31 | GPIO35/TDI | input | JTAG test data input (default function) shared with GPIO35; enable the internal pull-up or add an external pull-up to avoid a floating input. |
| 32 | GPIO32 | bidirectional | General-purpose I/O 32 with I2CA_SDA, SPIB_CLK, EPWM8_B and ADCSOCBO alternate functions. |
| 33 | GPIO18/X2 | bidirectional | General-purpose I/O 18, or crystal oscillator output X2 when the crystal oscillator is enabled. |
| 34 | GPIO19/X1 | bidirectional | General-purpose I/O 19, or crystal oscillator / single-ended clock input X1; initialization software must configure this pin before enabling the crystal oscillator. |
| 35 | VDDIO | power_in | 3.3 V digital I/O supply. |
| 36 | VDD | power_in | 1.2 V digital logic supply; decoupling capacitors are required. |
| 37 | VSS | power_in | Digital ground; must be connected to the board ground. |
| 38 | GPIO4 | bidirectional | General-purpose I/O 4 with EPWM3_A, MCAN_TX, CANA_TX and HIC_NWE alternate functions. |
| 39 | GPIO3 | bidirectional | General-purpose I/O 3 with EPWM2_B, PMBUSA_SCL, SCIA_RX and CANA_RX alternate functions. |
| 40 | GPIO2 | bidirectional | General-purpose I/O 2 with EPWM2_A, PMBUSA_SDA, SCIA_TX and CANA_TX alternate functions. |
| 41 | GPIO1 | bidirectional | General-purpose I/O 1 with EPWM1_B, I2CA_SCL, MCAN_TX and FSITXA_TDM_D1 alternate functions. |
| 42 | GPIO0 | bidirectional | General-purpose I/O 0 with EPWM1_A, I2CA_SDA, MCAN_RX and EQEP1_INDEX alternate functions. |
| 43 | GPIO7 | bidirectional | General-purpose I/O 7 with EPWM4_B, EQEP1_B, SPIB_SIMO and FSITXA_CLK alternate functions. |
| 44 | VSS | power_in | Digital ground; must be connected to the board ground. |
| 45 | VDD | power_in | 1.2 V digital logic supply; decoupling capacitors are required. |
| 46 | VDDIO | power_in | 3.3 V digital I/O supply. |
| 47 | GPIO5 | bidirectional | General-purpose I/O 5 with EPWM3_B, OUTPUTXBAR3, MCAN_RX and CANA_RX alternate functions. |
| 48 | GPIO6 | bidirectional | General-purpose I/O 6 with EPWM4_A, OUTPUTXBAR4, SYNCOUT and EQEP1_A alternate functions. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Low-level output voltage | VOL | 0.4 | V | IOL = IOL max | 71 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 100µA | 71 | ||
| High-level output impedance, all output pins | ROH | 50 | 66 | 96 | Ω | VOH=VDDIO-0.4V | 71 |
| Low-level output impedance, all output pins | ROL | 48 | 60 | 84 | Ω | VOL = 0.4V | 71 |
| High-level input voltage | VIH | 2 | V | 71 | |||
| Low-level input voltage | VIL | 0.8 | V | 71 | |||
| Weak pull-down resistance | RPULLDOWN | 22 | 31 | 62 | kΩ | 71 | |
| Weak pull-up resistance | RPULLUP | 19 | 30 | 54 | kΩ | 71 | |
| Internal regulator output | VVREG | 1.14 | 1.2 | 1.32 | V | 83 | |
| VDDIO supply ramp-up rate | SRVDDIO-UP | 8 | 100 | mV/μs | 3.3V rail (VDDIO) | 83 | |
| VDDIO supply ramp-down rate | SRVDDIO-DN | 20 | 100 | mV/μs | 3.3V rail (VDDIO) | 83 | |
| VDD supply ramp-up rate | SRVDD-UP | 3.5 | 100 | mV/μs | 1.2V rail (VDD) | 83 | |
| VDD supply ramp-down rate | SRVDD-DN | 10 | 100 | mV/μs | 1.2V rail (VDD) | 83 | |
| Crystal load capacitance | CL1, CL2 | 12 | 24 | pF | 98 | ||
| Crystal shunt capacitance | C0 | 7 | pF | 98 | |||
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.82 | 10 | 10.1 | MHz | -40℃ to 125℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.86 | 10 | 10.1 | MHz | -30℃ to 90℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.9 | 10 | 10.1 | MHz | -10℃ to 85℃ | 100 |
| INTOSC frequency stability at room temperature | fINTOSC-STABILITY | -0.1 | 0.1 | % | 30°C, nominal VDD | 100 | |
| CMPSS comparator hysteresis 1x | 4 | 12 | 20 | LSB | 141 | ||
| CMPSS comparator hysteresis 2x | 17 | 24 | 33 | LSB | 141 | ||
| CMPSS comparator hysteresis 3x | 25 | 36 | 50 | LSB | 141 | ||
| CMPSS comparator hysteresis 4x | 30 | 48 | 67 | LSB | 141 | ||
| CMPSS comparator input-referred offset voltage error | -20 | 20 | mV | Low common mode, inverting input set to 50mV | 141 | ||
| CMPSS DAC static offset voltage error | -25 | 25 | mV | 142 | |||
| CMPSS DAC static gain error | -2 | 2 | FSR 百分比 | 142 | |||
| CMPSS DAC static DNL | -1 | 4 | LSB | corrected endpoints | 142 | ||
| CMPSS DAC static INL | -16 | 16 | LSB | corrected endpoints | 142 | ||
| Buffered DAC offset error | -10 | 10 | mV | midpoint | 146 | ||
| Buffered DAC gain error | -2.5 | 2.5 | FSR 百分比 | 146 | |||
| Buffered DAC differential nonlinearity | DNL | -1 | 1 | LSB | corrected endpoints | 146 | |
| Buffered DAC integral nonlinearity | INL | -5 | 5 | LSB | corrected endpoints | 146 | |
| PMBus input voltage low | VIL | 0.8 | V | 171 | |||
| PMBus input voltage high | VIH | 2.1 | V | 171 | |||
| PMBus low-level output voltage | VOL | 0.4 | V | Ipullup = 4mA | 171 | ||
| PMBus spike pulse width suppressed by input filter | tSP | 0 | 50 | ns | 171 | ||
| PMBus input leakage current per pin | Ii | -10 | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 171 | |
| PMBus fast mode SCL clock frequency | fSCL | 10 | 400 | kHz | 171 | ||
| PMBus fast mode bus free time between stop and start | tBUF | 1.3 | µs | 171 | |||
| PMBus fast mode start condition hold time | tHD;STA | 0.6 | µs | 171 | |||
| PMBus fast mode repeated start setup time | tSU;STA | 0.6 | µs | 171 | |||
| PMBus fast mode stop condition setup time | tSU;STO | 0.6 | µs | 171 | |||
| PMBus fast mode data hold time after SCL falling | tHD;DAT | 300 | ns | 171 | |||
| PMBus fast mode data setup time before SCL rising | tSU;DAT | 100 | ns | 171 | |||
| PMBus fast mode SCL low period | tLOW | 1.3 | µs | 171 | |||
| PMBus fast mode SCL high period | tHIGH | 0.6 | 50 | µs | 171 | ||
| PMBus fast mode SDA and SCL rise time | tr | 20 | 300 | ns | 5% to 95% | 171 | |
| PMBus fast mode SDA and SCL fall time | tf | 20 | 300 | ns | 95% to 5% | 171 | |
| PMBus standard mode SCL clock frequency | fSCL | 10 | 100 | kHz | 172 | ||
| PMBus standard mode bus free time between stop and start | tBUF | 4.7 | µs | 172 | |||
| PMBus standard mode start condition hold time | tHD;STA | 4 | µs | 172 | |||
| PMBus standard mode repeated start setup time | tSU;STA | 4.7 | µs | 172 | |||
| PMBus standard mode stop condition setup time | tSU;STO | 4 | µs | 172 | |||
| PMBus standard mode data hold time after SCL falling | tHD;DAT | 300 | ns | 172 | |||
| PMBus standard mode data setup time before SCL rising | tSU;DAT | 250 | ns | 172 | |||
| PMBus standard mode SCL low period | tLOW | 4.7 | µs | 172 | |||
| PMBus standard mode SCL high period | tHIGH | 4 | 50 | µs | 172 | ||
| PMBus standard mode SDA and SCL rise time | tr | 1000 | ns | 172 | |||
| PMBus standard mode SDA and SCL fall time | tf | 300 | ns | 172 |
CAD (KiCad official)
- Symbol:
F280034PTRQ1 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
f280034ptrq1-etched.step/f280034ptrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280034ptrq1.step/f280034ptrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (285 pp, sha256
4385cb7a74ef5d7f, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).