3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP73213-B6SI
Microchip Tech · Battery Management ICs · DFN-10(3x3)
MCP73213-B6SI from Microchip Tech, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Battery management input supply; recommended [VREG(typ)+0.3V] to 13.0V, bypass to VSS with at least 1 µF, rated 18V absolute maximum. |
| 2 | VDD | power_in | Battery management input supply; recommended [VREG(typ)+0.3V] to 13.0V, bypass to VSS with at least 1 µF, rated 18V absolute maximum. |
| 3 | VBAT | power_in | Battery charge control output connected to the positive battery terminal, bypassed to VSS with at least 1 µF for loop stability. |
| 4 | VBAT | power_in | Battery charge control output connected to the positive battery terminal, bypassed to VSS with at least 1 µF for loop stability. |
| 5 | NC | unconnected | No connection. |
| 6 | NC | unconnected | No connection. |
| 7 | STAT | output | Open-drain charge status output for driving an LED or, with a pull-up resistor, interfacing to a host microcontroller. |
| 8 | VSS | power_in | Battery management 0V reference, connected to the negative terminal of the battery and input supply. |
| 9 | VSS | power_in | Battery management 0V reference, connected to the negative terminal of the battery and input supply. |
| 10 | PROG | bidirectional | Fast charge current is set by a resistor to VSS (130 mA to 1100 mA); a typical 200 kΩ impedance puts the device in standby, so it also serves as charge enable. |
| 11 | EP | passive | Exposed thermal pad, connected to exposed PCB copper area (with vias) for thermal enhancement. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VDD | 4 | 16 | V | 5 | ||
| Operating Supply Voltage | VDD | 4.2 | 13 | V | 5 | ||
| Supply Current, Shutdown | ISS | 4 | 5.5 | μA | Shutdown (VDD ≤ VBAT, 150 mV) | 5 | |
| Supply Current, Charging | ISS | 700 | 1500 | μA | Charging | 5 | |
| Supply Current, Standby | ISS | 50 | 125 | μA | Standby (PROG Floating) | 5 | |
| Supply Current, Charge Complete | ISS | 50 | 150 | μA | Charge Complete; No Battery; VDD < VSTOP | 5 | |
| Output Reverse Leakage Current, Standby | IDISCHARGE | 0.5 | 2 | μA | Standby (PROG Floating) | 5 | |
| Output Reverse Leakage Current, Shutdown | IDISCHARGE | 0.5 | 2 | μA | Shutdown (VDD ≤ VBAT or VDD < VSTOP) | 5 | |
| Output Reverse Leakage Current, Charge Complete | IDISCHARGE | 10 | 17 | μA | Charge Complete; VDD is present | 5 | |
| UVLO Start Threshold | VSTART | 4.1 | 4.15 | 4.25 | V | 5 | |
| UVLO Stop Threshold | VSTOP | 4 | 4.05 | 4.1 | V | 5 | |
| OVP Start Threshold | VOVP | 12.8 | 13 | 13.2 | V | 5 | |
| Regulated Output Voltage (8.20V option) | VREG | 8.15 | 8.2 | 8.25 | V | TA= -5°C to +55°C; VDD = [VREG(Typical)+1V]; IOUT = 50 mA | 5 |
| Regulated Output Voltage (8.40V option) | VREG | 8.35 | 8.4 | 8.45 | V | TA= -5°C to +55°C; VDD = [VREG(Typical)+1V]; IOUT = 50 mA | 5 |
| Regulated Output Voltage (8.70V option) | VREG | 8.65 | 8.7 | 8.75 | V | TA= -5°C to +55°C; VDD = [VREG(Typical)+1V]; IOUT = 50 mA | 5 |
| Regulated Output Voltage (8.80V option) | VREG | 8.75 | 8.8 | 8.85 | V | TA= -5°C to +55°C; VDD = [VREG(Typical)+1V]; IOUT = 50 mA | 5 |
| Output Voltage Tolerance | VRTOL | -0.6 | 0.6 | % | 5 | ||
| Line Regulation | /ΔVBAT/VBAT//ΔVDD | 0.05 | 0.2 | %/V | VDD = [VREG(Typical)+1V] to 12V; IOUT = 50 mA | 5 | |
| Load Regulation | /ΔVBAT/VBAT/ | 0.05 | 0.2 | % | IOUT = 50 mA, 150 mA; VDD = [VREG(Typical)+1V] | 5 | |
| Fast Charge Current Regulation | IREG | 130 | 1100 | mA | TA = -5°C to +55°C | 6 | |
| Fast Charge Current Regulation, PROG = 10 kΩ | IREG | 117 | 130 | 143 | mA | PROG = 10 kΩ | 6 |
| Fast Charge Current Regulation, PROG = 1.1 kΩ | IREG | 900 | 1000 | 1100 | mA | PROG = 1.1 kΩ | 6 |
| Precondition Voltage Threshold Ratio (66.5% option) | VPTH/VREG | 64 | 66.5 | 69 | % | VBAT Low-to-High | 6 |
| Precondition Voltage Threshold Ratio (71.5% option) | VPTH/VREG | 69 | 71.5 | 74 | % | VBAT Low-to-High | 6 |
| Charge Termination Current Ratio (5% option) | ITERM/IREG | 3.7 | 5 | 6.3 | % | PROG = 1 kΩ to 10 kΩ; TA=-5°C to +55°C | 6 |
| Charge Termination Current Ratio (7.5% option) | ITERM/IREG | 5.6 | 7.5 | 9.4 | % | PROG = 1 kΩ to 10 kΩ; TA=-5°C to +55°C | 6 |
| Charge Termination Current Ratio (10% option) | ITERM/IREG | 7.5 | 10 | 12.5 | % | PROG = 1 kΩ to 10 kΩ; TA=-5°C to +55°C | 6 |
| Charge Termination Current Ratio (20% option) | ITERM/IREG | 15 | 20 | 25 | % | PROG = 1 kΩ to 10 kΩ; TA=-5°C to +55°C | 6 |
| Recharge Voltage Threshold Ratio | VRTH/VREG | 93 | 95 | 97 | % | VBAT High-to-Low | 6 |
| Status Sink Current | ISINK | 20 | 35 | mA | 6 | ||
| Status Low Output Voltage | VOL | 0.2 | 0.5 | V | ISINK = 4 mA | 6 | |
| Status Input Leakage Current | ILK | 0.001 | 1 | μA | High Impedance, VDD on pin | 6 | |
| Charge Impedance Range | RPROG | 1 | 22 | kΩ | 6 | ||
| Elapsed Timer Period (4 hr option) | tELAPSED | 3.6 | 4 | 4.4 | Hours | 7 | |
| Elapsed Timer Period (6 hr option) | tELAPSED | 5.4 | 6 | 6.6 | Hours | 7 | |
| Elapsed Timer Period (8 hr option) | tELAPSED | 7.2 | 8 | 8.8 | Hours | 7 | |
| Preconditioning Timer Period | tPRECHG | 0.4 | 0.5 | 0.6 | Hours | 7 | |
| Status Output Turn-Off | tOFF | 500 | μs | ISINK = 1 mA to 0 mA (Note 1) | 7 | ||
| Status Output Turn-On | tON | 500 | μs | ISINK = 0 mA to 1 mA (Note 1) | 7 | ||
| Specified Temperature Range | TA | -40 | 85 | °C | 7 | ||
| Operating Temperature Range | TJ | -40 | 125 | °C | 7 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 7 | ||
| PROG Voltage | VPROG | 6 | V | 5 | |||
| All Inputs and Outputs w.r.t. VSS | -0.3 | V | -0.3 to (VDD+0.3)V | 5 | |||
| Storage Temperature | -65 | 150 | °C | 5 | |||
| ESD Protection on All Pins, HBM | 4 | kV | HBM | 5 | |||
| ESD Protection on All Pins, MM | 300 | V | MM | 5 | |||
| Thermal Resistance Junction-to-Ambient, DFN-10LD (3x3) | θJA | 62 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 7 | ||
| Thermal Resistance Junction-to-Case, DFN-10LD (3x3) | θJC | 20.5 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 7 | ||
| Thermal Shutdown Die Temperature | TSD | 150 | °C | 7 | |||
| Thermal Shutdown Hysteresis | TSDHYS | 10 | °C | 7 | |||
| UVLO Hysteresis | VHYS | 100 | mV | 5 | |||
| OVP Hysteresis | VOVPHYS | 150 | mV | 5 | |||
| Pass Transistor ON-Resistance | RDSON | 350 | mΩ | VDD = 4.5V, TJ = 105°C (Note 1) | 6 | ||
| BSP Regulation Current | ISHORT | 25 | mA | 6 | |||
| BSP Start Threshold | VSHORT | 3.4 | V | 6 | |||
| Precondition Current Ratio | IPREG/IREG | 10 | % | PROG = 1 kΩ to 10 kΩ; TA=-5°C to +55°C | 6 | ||
| Supply Ripple Attenuation | PSRR | -46 | dB | IOUT = 20 mA, 10 Hz to 1 kHz | 6 |
CAD (KiCad official)
- Symbol:
MCP73213-B6SI - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files:
mcp73213-b6si-etched.step/mcp73213-b6si-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp73213-b6si.step/mcp73213-b6si.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (34 pp, sha256
43950b6737187b37, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).