3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM2852YMXAX-1.0
Texas Instruments · DC-DC Converters · HTSSOP-14-EP
LM2852YMXAX-1.0 from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVIN | power_in | Chip bias input that powers the logic of the chip; connect to the input voltage or a separate rail (2.85V to 5.5V recommended). |
| 2 | EN | input | Enable pin: connect to ground to disable the chip, connect to AVIN or leave floating to enable; internally pulled up. |
| 3 | SGND | power_in | Signal ground. |
| 4 | SS | input | Soft-start pin; connect a small capacitor to control startup, with capacitance restricted to 1 nF to 50 nF. |
| 5 | NC | unconnected | No connect; must be tied to ground or left floating in the application. |
| 6 | PVIN | power_in | Input supply pin connected to the input voltage and to the source of the internal power PFET (1.5V to 5.5V recommended). |
| 7 | PVIN | power_in | Input supply pin connected to the input voltage and to the source of the internal power PFET (1.5V to 5.5V recommended). |
| 8 | SW | output | Switch pin; connect to the output inductor. |
| 9 | SW | output | Switch pin; connect to the output inductor. |
| 10 | PGND | power_in | Power ground; connect to an internal ground plane or other large ground plane. |
| 11 | PGND | power_in | Power ground; connect to an internal ground plane or other large ground plane. |
| 12 | NC | unconnected | No connect; must be tied to ground or left floating in the application. |
| 13 | NC | unconnected | No connect; must be tied to ground or left floating in the application. |
| 14 | SNS | input | Output voltage sense pin; connect to the output voltage as close to the load as possible. |
| 15 | EP | power_in | Exposed pad; connect to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-14-EP |
| Category | Power Supply Chip |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage tolerance, 1-V option | VOUT | 0.9775 | 1.0225 | V | VOUT = 1-V option | 5 | |
| Line regulation (TJ -40 to 125°C) | ΔVOUT/ΔAVIN | 0.6 | % | VOUT = 1 V, 2.85 V ≤ AVIN ≤ 5.5 V, TJ = -40°C to 125°C | 5 | ||
| Line regulation (25°C) | ΔVOUT/ΔAVIN | 0.2 | % | VOUT = 1 V, 2.85 V ≤ AVIN ≤ 5.5 V, TJ = 25°C | 5 | ||
| Load regulation | ΔVOUT/ΔIO | 8 | mV/A | Normal operation, TJ = 25°C | 5 | ||
| UVLO threshold rising (AVIN) | VON | 2.85 | V | Rising, TJ = -40°C to 125°C | 5 | ||
| UVLO threshold rising (AVIN) 25°C | VON | 2.47 | V | Rising, TJ = 25°C | 5 | ||
| UVLO falling hysteresis | VON | 85 | 210 | mV | Falling hysteresis, TJ = -40°C to 125°C | 5 | |
| UVLO falling hysteresis 25°C | VON | 150 | mV | Falling hysteresis, TJ = 25°C | 5 | ||
| PFET ON resistance | rDSON-P | 140 | mΩ | Isw = 2 A, TJ = -40°C to 125°C | 5 | ||
| PFET ON resistance 25°C | rDSON-P | 75 | mΩ | Isw = 2 A, TJ = 25°C | 5 | ||
| NFET ON resistance | rDSON-N | 120 | mΩ | Isw = 2 A, TJ = -40°C to 125°C | 5 | ||
| NFET ON resistance 25°C | rDSON-N | 55 | mΩ | Isw = 2 A, TJ = 25°C | 5 | ||
| Soft-start resistance | RSS | 400 | kΩ | TJ = 25°C | 5 | ||
| Peak current limit threshold | ICL | 2.25 | 3.65 | A | LM2852Y, TJ = -40°C to 125°C | 5 | |
| Peak current limit threshold 25°C | ICL | 3 | A | LM2852Y, TJ = 25°C | 5 | ||
| Operating current | IQ | 2 | mA | Non-switching, TJ = -40°C to 125°C | 5 | ||
| Operating current 25°C | IQ | 0.85 | mA | Non-switching, TJ = 25°C | 5 | ||
| Shutdown quiescent current | ISD | 25 | µA | EN = 0 V, TJ = -40°C to 125°C | 5 | ||
| Shutdown quiescent current 25°C | ISD | 10 | µA | EN = 0 V, TJ = 25°C | 5 | ||
| Sense pin resistance | RSNS | 400 | kΩ | TJ = 25°C | 5 | ||
| Oscillator frequency | fosc | 325 | 625 | kHz | LM2852Y 500-kHz option, TJ = -40°C to 125°C | 6 | |
| Oscillator frequency 25°C | fosc | 500 | kHz | LM2852Y 500-kHz option, TJ = 25°C | 6 | ||
| Duty cycle | Drange | 0 | 100 | % | 6 | ||
| EN pin minimum high input | VIH | 75 | % of AVIN | 6 | |||
| EN pin maximum low input | VIL | 25 | % of AVIN | 6 | |||
| EN pin pullup current | IEN | 1.2 | µA | EN = 0 V, TJ = 25°C | 6 | ||
| Thermal shutdown temperature | TSD | 165 | °C | TJ = 25°C | 6 | ||
| Thermal shutdown hysteresis | TSD-HYS | 10 | °C | TJ = 25°C | 6 | ||
| PVIN to GND | PVIN | 1.5 | 5.5 | V | 4 | ||
| AVIN to GND | AVIN | 2.85 | 5.5 | V | 4 | ||
| Junction temperature | TJ | -40 | 125 | °C | 4 | ||
| PVIN, AVIN, EN, SNS | 6.5 | V | 4 | ||||
| Infrared soldering | 220 | °C | Infrared (15 sec) | 4 | |||
| Vapor phase soldering | 215 | °C | Vapor phase (60 sec) | 4 | |||
| Maximum junction temperature | 150 | °C | 4 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Junction-to-ambient thermal resistance | RθJA | 39.2 | °C/W | PWP (HTSSOP) 14 pins | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 24.1 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 20.1 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 0.6 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 19.8 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.7 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
LM2852YMXAX-1.0 - Footprint:
Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)
- 3D model files:
lm2852ymxax-1-0-etched.step/lm2852ymxax-1-0-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm2852ymxax-1-0.step/lm2852ymxax-1-0.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (30 pp, sha256
284b53595f280275, retrieved 2026-10-27, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).