3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownTPS3839K50DBZR
Texas Instruments · Monitors & Reset Circuits · SOT-23-3
TPS3839K50DBZR from Texas Instruments, in a SOT-23-3. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground reference pin for the device. |
| 2 | RESET | output | Active-low reset output with push-pull drive that can directly drive input pins; it stays low while VDD is below the factory threshold voltage and until the delay time (td) elapses after VDD rises above the threshold. |
| 3 | VDD | power_in | Supply voltage input; the device is specified for VDD from 0.9 V to 6.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-3 |
| Category | Power Management ICs |
| Pins | 3 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage | VDD | 0.9 | 6.5 | V | 7 | ||
| Supply current (into VDD pin) | IDD | 150 | 500 | nA | Output not connected | 7 | |
| Low-level output voltage (RESET pin) | VOL | 0.4 | V | VDD = 0.9 V to 1.2 V, IOL = 120 µA | 7 | ||
| Negative-going threshold voltage (TPS3839K50) | VIT- | 4.271 | 4.38 | 4.446 | V | TA = 25°C (threshold accuracy block heading) | 7 |
| Negative-going threshold accuracy | VIT- | -1 | 1 | % | TA = 25°C | 7 | |
| RESET delay time (power-up delay) | td | 120 | 200 | 350 | ms | 8 | |
| Propagation delay, VDD falling (power-down delay) | tPD_VDD | 20 | µs | 8 | |||
| Propagation delay from MR low to RESET low | tPD_MR | 46 | ns | 8 | |||
| Hysteresis voltage (TPS3839K50) | Vhys | 44 | mV | 7 | |||
| Minimum VDD voltage for valid output | V(POR) | 0.6 | V | IOL = 1 µA | 7 | ||
| Input supply voltage (absolute maximum, VDD and RESET) | VDD, RESET | -0.3 | 7 | V | Over operating free-air temperature range | 6 | |
| RESET pin current | -10 | 10 | mA | 6 | |||
| Operating ambient temperature | TA | -40 | 85 | °C | 6 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| Input supply voltage | VDD | 0.9 | 6.5 | V | Over operating free-air temperature range | 6 | |
| RESET pin voltage | VRESET | 0 | 6.5 | V | 6 | ||
| RESET pin current | IRESET | 0 | 8 | mA | 6 | ||
| Junction-to-ambient thermal resistance (DBZ) | RθJA | 346.6 | °C/W | DBZ (SOT23-3) package | 6 | ||
| Junction-to-case (top) thermal resistance (DBZ) | RθJC(top) | 124.4 | °C/W | DBZ (SOT23-3) package | 6 | ||
| Junction-to-board thermal resistance (DBZ) | RθJB | 78.9 | °C/W | DBZ (SOT23-3) package | 6 | ||
| Junction-to-top characterization parameter (DBZ) | ψJT | 11.5 | °C/W | DBZ (SOT23-3) package | 6 | ||
| Junction-to-board characterization parameter (DBZ) | ψJB | 77.3 | °C/W | DBZ (SOT23-3) package | 6 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
TPS3839K50DBZR - Footprint:
Package_TO_SOT_SMD:SOT-23-3 - 3D model: SOT-23-3, generated on the KiCad land (body 1.3 x 2.92 mm, terminals on the pads, 1.12 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
tps3839k50dbzr-etched.step/tps3839k50dbzr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps3839k50dbzr.step/tps3839k50dbzr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (35 pp, sha256
a18940237afc63cf, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).