Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TLV70212DBVR-HXY

HXY MOSFET · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5L

TLV70212DBVR-HXY from HXY MOSFET, in a SOT-23-5L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VIN power_in Input voltage pin; the datasheet gives a maximum input voltage of 6.5 V (DC characteristics) and an absolute maximum supply voltage of -0.3 to +8 V, and recommends a 10 uF input capacitor between VIN and VSS.
2 GND power_in Ground (VSS) reference pin; the output capacitor and input capacitor should be connected as close as possible to this pin and VOUT/VIN.
3 CE input ON/OFF control input with CMOS hysteresis; logic high requires at least 1.5 V and logic low is 0.4 V maximum at VIN = 5.0 V, and a low level shuts the IC down and pulls VOUT to VSS through the internal pull-down; any series resistor on CE must be under 10 kOhm.
4 NC unconnected No connect pin, not internally connected to the circuit.
5 VOUT power_out Regulated output voltage pin (0.9 V to 5.0 V in 100 mV steps); it supplies up to 300 mA at VIN - VOUT = 1 V and requires an output capacitor of at least 10 uF.

Key specifications

Parameter Value
Manufacturer HXY MOSFET
Package SOT-23-5L
Category Power Management (PMIC)
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VIN -0.3 8 V 2
Storage temperature range STG -50 125 °C 2
Operating temperature TA -40 85 °C 2
Output voltage accuracy (Vout ≤ 2.5V row; printed as Vout -0.05 / Vout +0.05) Vout -0.05 0.05 V Vin=Vout+1V; 1.0mA≤Iout≤100mA 3
Line regulation △Vout1/(△Vin·Vout) 0.05 0.2 %/V 4.3V≤Vin≤8V; Iout=10mA 3
Load regulation △Vout 15 40 mV Vin= 4.3V; 1.0mA≤Iout≤100mA 3
Output voltage temperature coefficient △Vout/(Ta·Vout) -100 100 Ppm/℃ Iout=30mA; 0℃≤Ta≤70℃ 3
Supply current Iss 10 15 uA 3
Input voltage Vin 6.5 V 3
EN logic high voltage VENH 1.5 V VIN=5.0V 3
EN logic low voltage VENL 0.4 V VIN=5.0V 3
Thermal resistance, junction to ambient (SOT-23-5L) θJA 260 °C/W SOT-23-5L package 2
Power dissipation (SOT-23-5L) PW 0.4 W SOT-23-5L package 2

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: TLV70212DBVR-HXY
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5L, generated on the KiCad land (body 1.625 x 2.935 mm, terminals on the pads, 1.25 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tlv70212dbvr-hxy-etched.step / tlv70212dbvr-hxy-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tlv70212dbvr-hxy.step / tlv70212dbvr-hxy.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HXY MOSFET datasheet (6 pp, sha256 186bf2571c20d067, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF