TPS259474LRPWR
Public Made by Adomby adom
Texas Instruments Surge Protection Devices (SPDs), VQFN-10-HR(2x2). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗PCB Footprint
Open full view ↗Datasheet
Open in new tab ↗Contents
README
markdownTPS259474LRPWR
Texas Instruments · Surge Protection Devices (SPDs) · VQFN-10-HR(2x2)
TPS259474LRPWR from Texas Instruments, in a VQFN-10-HR(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/UVLO | input | Active high enable for the device; a resistor divider from the input supply to GND sets the undervoltage lockout threshold, and the pin must not be left floating. |
| 2 | OVLO | input | For TPS259474x, a resistor divider from supply to GND sets the overvoltage lockout threshold; the pin can also be used as an active low enable and must not be left floating. |
| 3 | PG | output | Open-drain power good indication for TPS259474x, asserted high when the internal powerpath is fully turned on and the PGTH input exceeds its threshold. |
| 4 | PGTH | input | Power good threshold input for TPS259474x that sets the voltage level used to qualify the PG output. |
| 5 | IN | power_in | Power input of the device; the absolute maximum input voltage is 28 V per the Absolute Maximum Ratings. |
| 6 | OUT | power_out | Power output of the device; reverse current flow from OUT to IN is blocked at all times by the back-to-back FETs. |
| 7 | DVDT | output | A capacitor from this pin to GND sets the output turn-on slew rate, and the pin should be left floating for the fastest turn-on slew rate. |
| 8 | GND | power_in | Ground reference for all internal circuits, which must be connected to system GND. |
| 9 | ILM | output | Sets the output current limit threshold through a resistor to GND and provides the analog load current monitor signal; the pin must not be left floating. |
| 10 | ITIMER | output | A capacitor from this pin to GND sets the overcurrent blanking interval, and the pin should be left open for the fastest response to overcurrent events. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-10-HR(2x2) |
| Category | Circuit Protection |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum Input Voltage Range (-40°C ≤ TJ ≤ 125°C) | VIN | 28 | V | -40°C ≤ TJ ≤ 125°C | 7 | ||
| Maximum Input Voltage Range (-10°C ≤ TJ ≤ 125°C) | VIN | 28 | V | -10°C ≤ TJ ≤ 125°C | 7 | ||
| Maximum input voltage rising slew rate | SRIN(R) | 100 | V/μs | 7 | |||
| Maximum input voltage falling slew rate | SRIN(F) | 10 | V/μs | 7 | |||
| Maximum Output Voltage Range (-40°C ≤ TJ ≤ 125°C) | VOUT | -0.3 | V | -40°C ≤ TJ ≤ 125°C | 7 | ||
| Maximum Output Voltage Range (-10°C ≤ TJ ≤ 125°C) | VOUT | -0.3 | V | -10°C ≤ TJ ≤ 125°C | 7 | ||
| Minimum Output Voltage Pulse | VOUT,PLS | -0.8 | V | < 1µs | 7 | ||
| Maximum Enable Pin Voltage Range | VEN/UVLO | -0.3 | 6.5 | V | 7 | ||
| Maximum OVLO Pin Voltage Range (TPS259470x/4x) | VOVLO | -0.3 | 6.5 | V | TPS259470x/4x | 7 | |
| Maximum PGTH Pin Voltage Range (TPS259472x/4x) | VPGTH | -0.3 | 6.5 | V | TPS259472x/4x | 7 | |
| Maximum PG Pin Voltage Range (TPS259472x/4x) | VPG | -0.3 | 6.5 | V | TPS259472x/4x | 7 | |
| Maximum Lead Temperature | TLEAD | 300 | °C | 7 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 7 | ||
| Input Voltage Range | VIN | 2.7 | 23 | V | 8 | ||
| Enable Pin Voltage Range | VEN/UVLO | 5 | V | 8 | |||
| OVLO Pin Voltage Range (TPS259470x/4x) | VOVLO | 0.5 | 1.5 | V | TPS259470x/4x | 8 | |
| PGTH Pin Voltage Range (TPS259472x/4x) | VPGTH | 5 | V | TPS259472x/4x | 8 | ||
| PG Pin Voltage Range (TPS259472x/4x) | VPG | 5 | V | TPS259472x/4x | 8 | ||
| ITIMER Pin Capacitor Voltage Rating | VITIMER | 4 | V | 8 | |||
| ILM Pin Resistance | RILM | 549 | 6650 | Ω | 8 | ||
| Continuous Switch Current | IMAX | 5.5 | A | TJ ≤ 125°C | 8 | ||
| Junction temperature | TJ | -40 | 125 | °C | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 41.7 | °C/W | Custom 4-layer PCB (2s2p), 8 thermal vias under device | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 74.5 | °C/W | JEDEC 4-layer PCB (2s2p), no thermal vias under device | 8 | ||
| Junction-to-top characterization parameter | ΨJT | 1 | °C/W | 8 | |||
| Junction-to-board characterization parameter | ΨJB | 20 | °C/W | Custom 4-layer PCB (2s2p), 8 thermal vias under device | 8 | ||
| Junction-to-board characterization parameter | ΨJB | 27.6 | °C/W | JEDEC 4-layer PCB (2s2p), no thermal vias under device | 8 | ||
| Input supply UVP rising threshold | VUVP(R) | 2.44 | 2.53 | 2.64 | V | 8 | |
| Input supply UVP falling threshold | VUVP(F) | 2.35 | 2.42 | 2.55 | V | 8 | |
| EN/UVLO UVLO rising threshold | VUVLO(R) | 1.183 | 1.2 | 1.223 | V | 8 | |
| EN/UVLO UVLO falling threshold | VUVLO(F) | 1.076 | 1.09 | 1.116 | V | 8 | |
| OVLO rising threshold | VOV(R) | 1.183 | 1.2 | 1.223 | V | TPS259470x/4x | 9 |
| OVLO falling threshold | VOV(F) | 1.076 | 1.09 | 1.116 | V | TPS259470x/4x | 9 |
| Overcurrent threshold | ILIM | 0.425 | 0.5 | 0.575 | A | RILM = 6.65kΩ | 9 |
| Overcurrent threshold | ILIM | 0.85 | 1.007 | 1.15 | A | RILM = 3.32kΩ | 9 |
| Overcurrent threshold | ILIM | 1.8 | 2.028 | 2.2 | A | RILM = 1.65kΩ | 9 |
| Overcurrent threshold | ILIM | 3.96 | 4.452 | 4.84 | A | RILM = 750Ω | 9 |
| Overcurrent threshold | ILIM | 5.4 | 6.068 | 6.6 | A | RILM = 549Ω | 9 |
| ITIMER pin internal pull-up voltage | VINT | 2.3 | 2.57 | 2.72 | V | 10 | |
| ITIMER pin internal discharge current | IITIMER | 1.2 | 1.8 | 2.5 | µA | IOUT > ILIM | 10 |
| ITIMER discharge differential voltage threshold | ΔVITIMER | 1.286 | 1.51 | 1.741 | V | 10 | |
| Analog Load Current Monitor Gain (IMON : IOUT) | GIMON | 165 | 182 | 200 | µA/A | IOUT = 0.5A to 1A, IOUT < ILIM | 10 |
| VIN, VOUT threshold for fast BFET turn off (enter reverse current blocking) | VREVTH | -36.45 | -29.3 | -22.3 | mV | 10 | |
| VIN, VOUT threshold for fast BFET turn on (exit reverse current blocking) | VFWDTH | 83 | 104.1 | 125 | mV | 10 | |
| PGTH rising threshold | VPGTH(R) | 1.183 | 1.2 | 1.223 | V | 10 | |
| PGTH falling threshold | VPGTH(F) | 1.076 | 1.09 | 1.116 | V | 10 | |
| dVdt pin charging current | IdVdt | 0.81 | 2.21 | 3.82 | µA | 11 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • The GND terminal must be tied to the PCB ground plane at the terminal of the IC with the shortest possible trace. The PCB ground must be a copper plane or island on the board. TI recommends to have | 63 |
CAD (Adom-generated)
- Symbol:
TPS259474LRPWR - Footprint:
Adom_Gen:Texas_Instruments_TPS259474_9d621c - 3D model: generated to fit the land (STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (75 pp, sha256
8f96de3899030916, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.