main
Download ZIP Propose a change
Generated by adom_assets · KiCad file format 20240108
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers tps259474lrpwr: viewers rendered from the public page · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md tps259474lrpwr: CAD wording names the Adom_Gen land, not KiCad official · Ray
tps259474lrpwr-hero.glb Publish 0.1.0 · Ray
tps259474lrpwr-hero.overlay.json Publish 0.1.0 · Ray
tps259474lrpwr.glb Publish 0.1.0 · Ray
tps259474lrpwr.kicad_mod Publish 0.1.0 · Ray
tps259474lrpwr.kicad_sym Publish 0.1.0 · Ray
tps259474lrpwr.lbr Publish 0.1.0 · Ray
tps259474lrpwr.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 10 pins · Ray

TPS259474LRPWR

Texas Instruments · Surge Protection Devices (SPDs) · VQFN-10-HR(2x2)

TPS259474LRPWR from Texas Instruments, in a VQFN-10-HR(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 EN/UVLO input Active high enable for the device; a resistor divider from the input supply to GND sets the undervoltage lockout threshold, and the pin must not be left floating.
2 OVLO input For TPS259474x, a resistor divider from supply to GND sets the overvoltage lockout threshold; the pin can also be used as an active low enable and must not be left floating.
3 PG output Open-drain power good indication for TPS259474x, asserted high when the internal powerpath is fully turned on and the PGTH input exceeds its threshold.
4 PGTH input Power good threshold input for TPS259474x that sets the voltage level used to qualify the PG output.
5 IN power_in Power input of the device; the absolute maximum input voltage is 28 V per the Absolute Maximum Ratings.
6 OUT power_out Power output of the device; reverse current flow from OUT to IN is blocked at all times by the back-to-back FETs.
7 DVDT output A capacitor from this pin to GND sets the output turn-on slew rate, and the pin should be left floating for the fastest turn-on slew rate.
8 GND power_in Ground reference for all internal circuits, which must be connected to system GND.
9 ILM output Sets the output current limit threshold through a resistor to GND and provides the analog load current monitor signal; the pin must not be left floating.
10 ITIMER output A capacitor from this pin to GND sets the overcurrent blanking interval, and the pin should be left open for the fastest response to overcurrent events.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-10-HR(2x2)
Category Circuit Protection
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Maximum Input Voltage Range (-40°C ≤ TJ ≤ 125°C) VIN 28 V -40°C ≤ TJ ≤ 125°C 7
Maximum Input Voltage Range (-10°C ≤ TJ ≤ 125°C) VIN 28 V -10°C ≤ TJ ≤ 125°C 7
Maximum input voltage rising slew rate SRIN(R) 100 V/μs 7
Maximum input voltage falling slew rate SRIN(F) 10 V/μs 7
Maximum Output Voltage Range (-40°C ≤ TJ ≤ 125°C) VOUT -0.3 V -40°C ≤ TJ ≤ 125°C 7
Maximum Output Voltage Range (-10°C ≤ TJ ≤ 125°C) VOUT -0.3 V -10°C ≤ TJ ≤ 125°C 7
Minimum Output Voltage Pulse VOUT,PLS -0.8 V < 1µs 7
Maximum Enable Pin Voltage Range VEN/UVLO -0.3 6.5 V 7
Maximum OVLO Pin Voltage Range (TPS259470x/4x) VOVLO -0.3 6.5 V TPS259470x/4x 7
Maximum PGTH Pin Voltage Range (TPS259472x/4x) VPGTH -0.3 6.5 V TPS259472x/4x 7
Maximum PG Pin Voltage Range (TPS259472x/4x) VPG -0.3 6.5 V TPS259472x/4x 7
Maximum Lead Temperature TLEAD 300 °C 7
Storage temperature TSTG -65 150 °C 7
Input Voltage Range VIN 2.7 23 V 8
Enable Pin Voltage Range VEN/UVLO 5 V 8
OVLO Pin Voltage Range (TPS259470x/4x) VOVLO 0.5 1.5 V TPS259470x/4x 8
PGTH Pin Voltage Range (TPS259472x/4x) VPGTH 5 V TPS259472x/4x 8
PG Pin Voltage Range (TPS259472x/4x) VPG 5 V TPS259472x/4x 8
ITIMER Pin Capacitor Voltage Rating VITIMER 4 V 8
ILM Pin Resistance RILM 549 6650 Ω 8
Continuous Switch Current IMAX 5.5 A TJ ≤ 125°C 8
Junction temperature TJ -40 125 °C 8
Junction-to-ambient thermal resistance RθJA 41.7 °C/W Custom 4-layer PCB (2s2p), 8 thermal vias under device 8
Junction-to-ambient thermal resistance RθJA 74.5 °C/W JEDEC 4-layer PCB (2s2p), no thermal vias under device 8
Junction-to-top characterization parameter ΨJT 1 °C/W 8
Junction-to-board characterization parameter ΨJB 20 °C/W Custom 4-layer PCB (2s2p), 8 thermal vias under device 8
Junction-to-board characterization parameter ΨJB 27.6 °C/W JEDEC 4-layer PCB (2s2p), no thermal vias under device 8
Input supply UVP rising threshold VUVP(R) 2.44 2.53 2.64 V 8
Input supply UVP falling threshold VUVP(F) 2.35 2.42 2.55 V 8
EN/UVLO UVLO rising threshold VUVLO(R) 1.183 1.2 1.223 V 8
EN/UVLO UVLO falling threshold VUVLO(F) 1.076 1.09 1.116 V 8
OVLO rising threshold VOV(R) 1.183 1.2 1.223 V TPS259470x/4x 9
OVLO falling threshold VOV(F) 1.076 1.09 1.116 V TPS259470x/4x 9
Overcurrent threshold ILIM 0.425 0.5 0.575 A RILM = 6.65kΩ 9
Overcurrent threshold ILIM 0.85 1.007 1.15 A RILM = 3.32kΩ 9
Overcurrent threshold ILIM 1.8 2.028 2.2 A RILM = 1.65kΩ 9
Overcurrent threshold ILIM 3.96 4.452 4.84 A RILM = 750Ω 9
Overcurrent threshold ILIM 5.4 6.068 6.6 A RILM = 549Ω 9
ITIMER pin internal pull-up voltage VINT 2.3 2.57 2.72 V 10
ITIMER pin internal discharge current IITIMER 1.2 1.8 2.5 µA IOUT > ILIM 10
ITIMER discharge differential voltage threshold ΔVITIMER 1.286 1.51 1.741 V 10
Analog Load Current Monitor Gain (IMON : IOUT) GIMON 165 182 200 µA/A IOUT = 0.5A to 1A, IOUT < ILIM 10
VIN, VOUT threshold for fast BFET turn off (enter reverse current blocking) VREVTH -36.45 -29.3 -22.3 mV 10
VIN, VOUT threshold for fast BFET turn on (exit reverse current blocking) VFWDTH 83 104.1 125 mV 10
PGTH rising threshold VPGTH(R) 1.183 1.2 1.223 V 10
PGTH falling threshold VPGTH(F) 1.076 1.09 1.116 V 10
dVdt pin charging current IdVdt 0.81 2.21 3.82 µA 11

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper • The GND terminal must be tied to the PCB ground plane at the terminal of the IC with the shortest possible trace. The PCB ground must be a copper plane or island on the board. TI recommends to have 63

CAD (Adom-generated)

  • Symbol: TPS259474LRPWR
  • Footprint: Adom_Gen:Texas_Instruments_TPS259474_9d621c
  • 3D model: generated to fit the land (STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (75 pp, sha256 8f96de3899030916, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.

Datasheet PDF