3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F411CEU6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)
STM32F411CEU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup battery supply pin for RTC and low-power domain, 1.7 V to 3.6 V. |
| 2 | PC13-ANTI_TAMP | bidirectional | PC13 GPIO with RTC anti-tamper, RTC output, and RTC timestamp functions, 5 V tolerant with 2 MHz max speed and 30 pF load limit. |
| 3 | PC14-OSC32_IN | bidirectional | PC14 GPIO with 32 kHz oscillator input function, 5 V tolerant except in oscillator mode. |
| 4 | PC15-OSC32_OUT | bidirectional | PC15 GPIO with 32 kHz oscillator output function, 5 V tolerant. |
| 5 | PH0-OSC_IN | bidirectional | PH0 GPIO with main oscillator input function, 5 V tolerant except in oscillator mode. |
| 6 | PH1-OSC_OUT | bidirectional | PH1 GPIO with main oscillator output function, 5 V tolerant. |
| 7 | NRST | bidirectional | Reset pin with embedded weak pull-up resistor, 5 V tolerant, active low reset trigger. |
| 8 | VSSA/VREF- | power_in | Analog ground, one pin with VREF- on UFQFPN48 (Figure 10 labels it VSSA/VREF-); VREF- is internally connected to VSSA. |
| 9 | VDDA/VREF+ | power_in | Analog supply and ADC positive reference, one pin on UFQFPN48 (Figure 10 labels it VDDA/VREF+); VREF+ is internally connected to VDDA. |
| 10 | PA0-WKUP | bidirectional | PA0 GPIO with wake-up and timer trigger capabilities, standard 3.3 V I/O, can trigger device wake-up from low-power modes. |
| 11 | PA1 | bidirectional | PA1 GPIO with SPI4/I2S4, USART2, timer, and ADC channel 1 functions, 5 V tolerant. |
| 12 | PA2 | bidirectional | PA2 GPIO with USART2 TX, timer channels, I2S2 clock, and ADC channel 2 functions, 5 V tolerant. |
| 13 | PA3 | bidirectional | PA3 GPIO with USART2 RX, timer channels, I2S2 clock, and ADC channel 3 functions, 5 V tolerant. |
| 14 | PA4 | bidirectional | PA4 GPIO with SPI1/SPI3 chip select, USART2 clock, and ADC channel 4 functions, 5 V tolerant. |
| 15 | PA5 | bidirectional | PA5 GPIO with SPI1 clock, timer channels, and ADC channel 5 functions, 5 V tolerant. |
| 16 | PA6 | bidirectional | PA6 GPIO with SPI1 MISO, SDIO command, timer brake, and ADC channel 6 functions, 5 V tolerant. |
| 17 | PA7 | bidirectional | PA7 GPIO with SPI1 MOSI, timer channel 1 complementary output, and ADC channel 7 functions, 5 V tolerant. |
| 18 | PB0 | bidirectional | PB0 GPIO with SPI5 clock, timer complementary channels, and ADC channel 8 functions, 5 V tolerant. |
| 19 | PB1 | bidirectional | PB1 GPIO with SPI5 chip select, timer complementary channels, and ADC channel 9 functions, 5 V tolerant. |
| 20 | PB2 | bidirectional | PB2 GPIO with BOOT1 function for boot mode configuration, 5 V tolerant. |
| 21 | PB10 | bidirectional | PB10 GPIO with I2C2 SCL, SPI2/I2S2 clock, and SDIO data functions, 5 V tolerant. |
| 22 | VCAP_1 | power_in | Voltage regulator output capacitor connection pin for internal voltage regulation. |
| 23 | VSS | power_in | Ground connection for digital circuits. |
| 24 | VDD | power_in | Main power supply pin, 1.7 V to 3.6 V. |
| 25 | PB12 | bidirectional | PB12 GPIO with SPI2/SPI3/SPI4 chip select, I2C2 alert, timer brake, and SDIO functions, 5 V tolerant. |
| 26 | PB13 | bidirectional | PB13 GPIO with SPI2/SPI4 clock, timer channel 1 complementary output, 5 V tolerant. |
| 27 | PB14 | bidirectional | PB14 GPIO with SPI2 MISO, I2S2 extended SD, SDIO data, and timer complementary output functions, 5 V tolerant. |
| 28 | PB15 | bidirectional | PB15 GPIO with SPI2 MOSI, RTC 50 Hz reference input, SDIO clock, and timer complementary output functions, 5 V tolerant. |
| 29 | PA8 | bidirectional | PA8 GPIO with MCO_1 master clock output, USART1 clock, I2C3 SCL, USB FS SOF, and SDIO data functions, 5 V tolerant. |
| 30 | PA9 | bidirectional | PA9 GPIO with USART1 TX, I2C3 alert, USB FS VBUS input, and SDIO data functions, 5 V tolerant. |
| 31 | PA10 | bidirectional | PA10 GPIO with USART1 RX, SPI5 MOSI, USB FS ID input, and timer channel functions, 5 V tolerant. |
| 32 | PA11 | bidirectional | PA11 GPIO with USART1 CTS, SPI4 MISO, USB FS D minus line, and timer channel functions, 5 V tolerant. |
| 33 | PA12 | bidirectional | PA12 GPIO with USART1 RTS, SPI5 MISO, USB FS D plus line, and timer ETR functions, 5 V tolerant. |
| 34 | PA13 | bidirectional | PA13 JTAG TMS and SWD IO pin for debug interface, 5 V tolerant. |
| 35 | VSS | power_in | Ground connection for digital circuits. |
| 36 | VDD | power_in | Main power supply pin, 1.7 V to 3.6 V. |
| 37 | PA14 | bidirectional | PA14 JTAG TCK and SWD clock pin for debug interface, 5 V tolerant. |
| 38 | PA15 | bidirectional | PA15 JTAG TDI and GPIO with SPI1/SPI3 chip select, USART1 TX, and timer functions, 5 V tolerant. |
| 39 | PB3 | bidirectional | PB3 JTAG TDO/SWO and GPIO with SPI1/SPI3 clock, USART1 RX, I2C2 SDA functions, 5 V tolerant. |
| 40 | PB4 | bidirectional | PB4 JTAG TRST and GPIO with SPI1/SPI3 MISO, I2C3 SDA, SDIO data functions, 5 V tolerant. |
| 41 | PB5 | bidirectional | PB5 GPIO with I2C1 alert, SPI1/SPI3 MOSI, SDIO data, and timer channel functions, standard 3.3 V I/O. |
| 42 | PB6 | bidirectional | PB6 GPIO with I2C1 SCL, USART1 TX, and timer channel functions, 5 V tolerant. |
| 43 | PB7 | bidirectional | PB7 GPIO with I2C1 SDA, USART1 RX, SDIO data, and timer channel functions, 5 V tolerant. |
| 44 | BOOT0 | input | Boot mode selection input pin, sampled during reset to determine boot source (flash or system memory), supports VPP programming voltage. |
| 45 | PB8 | bidirectional | PB8 GPIO with I2C1 SCL, SPI5 MOSI, I2C3 SDA, timer channels, and SDIO data functions, 5 V tolerant. |
| 46 | PB9 | bidirectional | PB9 GPIO with I2C1 SDA, SPI2 chip select, I2C2 SDA, timer channels, and SDIO data functions, 5 V tolerant. |
| 47 | VSS | power_in | Ground connection for digital circuits. |
| 48 | VDD | power_in | Main power supply pin, 1.7 V to 3.6 V. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDD-VSS (external main supply, incl. VDDA, VDD, VBAT) | VDD-VSS | -0.3 | 4 | V | 60 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 60 | ||
| Input voltage on FT and TC pins (minimum) | VIN | -0.3 | V | 60 | |||
| Input voltage for BOOT0 | VIN | 9 | V | 60 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 60 | |||
| Variations between all the different ground pins | /VSSX −VSS/ | 50 | mV | 60 | |||
| Total current into sum of all VDD_x power lines (source) | ΣIVDD | 160 | mA | 61 | |||
| Total current out of sum of all VSS_x ground lines (sink) | ΣIVSS | -160 | mA | 61 | |||
| Maximum current into each VDD_x power line (source) | IVDD | 100 | mA | 61 | |||
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | mA | 61 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 61 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 61 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 61 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | mA | 61 | |||
| Injected current on FT and TC pins | IINJ(PIN) | -5 | 0 | mA | 61 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 61 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 61 | ||
| Maximum junction temperature | TJ | 130 | °C | 61 | |||
| Internal AHB clock frequency | fHCLK | 0 | 64 | MHz | Power Scale3, regulator ON, VOS[1:0]=0x01 | 62 | |
| Internal AHB clock frequency | fHCLK | 0 | 84 | MHz | Power Scale2, regulator ON, VOS[1:0]=0x10 | 62 | |
| Internal AHB clock frequency | fHCLK | 0 | 100 | MHz | Power Scale1, regulator ON, VOS[1:0]=0x11 | 62 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 50 | MHz | 62 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 100 | MHz | 62 | ||
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 62 | ||
| Analog operating voltage (ADC limited to 1.2 M samples) | VDDA | 1.7 | 2.4 | V | Must be the same potential as VDD | 62 | |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | 3.6 | V | Must be the same potential as VDD | 62 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 62 | ||
| 1.2 V internal voltage on VCAP_1/VCAP_2 (regulator ON) | V12 | 1.08 | 1.14 | 1.2 | V | VOS[1:0]=0x01, max frequency 64 MHz | 62 |
| 1.2 V internal voltage on VCAP_1/VCAP_2 (regulator ON) | V12 | 1.2 | 1.26 | 1.32 | V | VOS[1:0]=0x10, max frequency 84 MHz | 62 |
| 1.2 V internal voltage on VCAP_1/VCAP_2 (regulator ON) | V12 | 1.26 | 1.32 | 1.38 | V | VOS[1:0]=0x11, max frequency 100 MHz | 62 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 62 | |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 62 | |
| Input voltage on BOOT0 pin | VIN | 0 | 9 | V | 62 | ||
| Power dissipation UFQFPN48 | PD | 625 | mW | TA = 85 °C (range 6) | 62 | ||
| Ambient temperature range 6, maximum power dissipation | TA | -40 | 85 | °C | Maximum power dissipation | 63 | |
| Ambient temperature range 6, low power dissipation | TA | -40 | 105 | °C | Low power dissipation | 63 | |
| Junction temperature range 6 | TJ | -40 | 105 | °C | Range 6 | 63 | |
| Capacitance of external capacitor CEXT | CEXT | 4.7 | µF | Single VCAP pin available | 64 | ||
| ESR of external capacitor | ESR | 1 | Ω | Single VCAP pin available | 64 | ||
| VDD rise time rate (regulator ON) | tVDD | 20 | µs/V | 65 | |||
| VDD fall time rate (regulator ON) | tVDD | 20 | µs/V | 65 | |||
| Power-on/power-down reset threshold | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 66 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 66 |
| PDR hysteresis | VPDRhyst | 40 | mV | 66 | |||
| PVD hysteresis | VPVDhyst | 100 | mV | 66 | |||
| Brownout level 1 threshold | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 66 |
| Brownout level 1 threshold | VBOR1 | 2.23 | 2.29 | 2.33 | V | Rising edge | 66 |
| Brownout level 2 threshold | VBOR2 | 2.44 | 2.5 | 2.56 | V | Falling edge | 66 |
| Brownout level 2 threshold | VBOR2 | 2.53 | 2.59 | 2.63 | V | Rising edge | 66 |
| Brownout level 3 threshold | VBOR3 | 2.75 | 2.83 | 2.88 | V | Falling edge | 66 |
| Brownout level 3 threshold | VBOR3 | 2.85 | 2.92 | 2.97 | V | Rising edge | 66 |
| BOR hysteresis | VBORhyst | 100 | mV | 66 | |||
| POR reset timing | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | 66 | |
| Supply current in Standby mode, VDD=3.6 V (LSE and RTC ON) | IDD_STBY | 2.8 | 5 | µA | Low-speed oscillator (LSE) and RTC ON, TA = 25 °C | 75 | |
| Supply current in Standby mode, VDD=3.6 V (LSE and RTC ON) | IDD_STBY | 14 | µA | Low-speed oscillator (LSE) and RTC ON, TA = 85 °C | 75 | ||
| Supply current in Standby mode, VDD=3.6 V (RTC and LSE OFF) | IDD_STBY | 2.1 | 4 | µA | RTC and LSE OFF, TA = 25 °C | 75 | |
| Supply current in Standby mode, VDD=3.6 V (RTC and LSE OFF) | IDD_STBY | 13.5 | µA | RTC and LSE OFF, TA = 85 °C | 75 | ||
| Supply current in Stop mode, VDD=3.6 V (Flash in Deep power down, low power regulator) | IDD_STOP | 14 | 38 | µA | Flash in Deep power down mode, all oscillators OFF, no independent watchdog, Low power regulator usage, TA = 25 °C | 75 | |
| Supply current in Stop mode, VDD=3.6 V (Flash in Deep power down, low power regulator) | IDD_STOP | 275 | µA | Flash in Deep power down mode, all oscillators OFF, no independent watchdog, Low power regulator usage, TA = 85 °C | 75 |
CAD (KiCad official)
- Symbol:
STM32F411CEU6 - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32f411ceu6-etched.step/stm32f411ceu6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f411ceu6.step/stm32f411ceu6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (146 pp, sha256
284b85ff62b02690, retrieved 2026-11-10, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).