3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCV7694MW0R2G
onsemi · LED Drivers · DFN-10-EP(3x3)
NCV7694MW0R2G from onsemi, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS | power_in | Supply voltage of the device; parametric operation is 7 V to 28 V, with continuous supply up to +40 V and load dump transient up to +40 V (t < 500 ms). |
| 2 | DIAG | output | Open-drain diagnostic output that reports Open Load, Short to VSTRING, Short to GND and thermal/undervoltage status; maximum rating is +40 V and output low is 0.4 V max at 0.33 mA when a fault is present. |
| 3 | FLASH | input | Logic input for flash exposure timing, compatible with 1.8 V / 2.8 V logic, rated −0.3 V to +3.6 V, with an internal pull-down of 120 kΩ typical. |
| 4 | RETL | passive | External resistor that sets the maximum exposure time limit (0.8 kΩ to 15 kΩ operating range); DC voltage rating is −0.3 V to +3.6 V. |
| 5 | RFRL | passive | External resistor that sets the maximum frame rate limit (0.8 kΩ to 15 kΩ operating range); DC voltage rating is −0.3 V to +3.6 V. |
| 6 | GND | power_in | Ground reference of the device. |
| 7 | FB | input | Feedback reference input regulated to 300 mV typical, which sets the LED current via R1; rated −0.3 V to +3.6 V and must stay below 0.19 V when the device is not active. |
| 8 | GATE | output | Gate drive for the external MOSFET, with a minimum gate ON voltage of 4.5 V and a pull-down resistance of 5 kΩ to 100 kΩ (30 kΩ typical). |
| 9 | DET | input | LED cathode sense input; during FLASH-on the voltage should be between 0.35 V and (VSTRING − 1.22 V), and the rating is −0.3 V to +40 V. |
| 10 | VSTRING | input | High-voltage input sensing the top of the LED string and enabling Open Load and Short diagnostics above VSTRth of 2.2 V; rated −0.3 V to +40 V. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | DFN-10-EP(3x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VS_OP | 7 | 28 | V | Parametric operation | 6 | |
| Supply Under-Voltage Lockout (VS rising) | VSUV | 4 | 4.5 | 5 | V | VS rising | 6 |
| Supply Under-Voltage hysteresis | VSUVhys | 150 | 300 | 550 | mV | 6 | |
| Supply Current in normal condition | I_VS | 4 | 6 | mA | VS = 14 V, FLASH = High, IFRL, IETL subtracted | 6 | |
| Supply Current in normal condition (FLASH low) | I_VS | 3.8 | 6 | mA | VS = 14 V, FLASH = Low, IFRL, IETL subtracted | 6 | |
| Supply Current in Fault condition | I_VSerr | 4 | 6 | mA | VS = 14 V, FLASH = High, Open Load condition, IFRL, IETL subtracted | 6 | |
| Thermal Shutdown (TSD) | 130 | 150 | 170 | °C | 6 | ||
| FB Regulation reference | VFBref | 270 | 300 | 330 | mV | Under Voltage Lockout < VS | 6 |
| Gate ON voltage | VGATE | 4.5 | V | FB = 220 mV, DET = 1.0 V | 6 | ||
| Propagation Delay FLASH rising to FB ON | tON | 8 | 15 | μs | 50% criterion | 6 | |
| Propagation Delay FLASH falling to FB OFF | tOFF | 6.6 | 15 | μs | 50% criterion | 6 | |
| FLASH propagation Delay Delta | tpd_delta | 1.4 | 4 | μs | /(Falling time), (Rising Time)/, 50% criterion | 6 | |
| Output pull-down resistance | RGATE | 5 | 30 | 100 | kΩ | 6 | |
| Input High Threshold | VinH | 1.3 | 1.2 | V | 6 | ||
| Input Low Threshold | VinL | 1.15 | 1.1 | V | 6 | ||
| Input pull-down resistance | RFLASH | 30 | 120 | 190 | kΩ | 6 | |
| RETL external resistor value operation range | RETL | 0.8 | 15 | kΩ | RETL external resistor value operation range | 6 | |
| Maximum TON time (typ) | TONmax | 6 | ms | Derived from RETL and KETL(typ); valid for RETL = 15 kΩ | 6 | ||
| KETL tolerance | tolETL | -13 | 13 | % | Tolerance of Exposure Time Limit | 6 | |
| Overcurrent protection RETL (short to ground) | IETL_lim | 1.3 | mA | Short to ground; resistor detection for RETL < 750 Ω | 6 | ||
| Open Load protection RETL | IETL_open | 57.5 | μA | Open Load detection; resistor detection for RETL > 17.5 kΩ | 6 | ||
| FRL resistor operation range | RFRL | 0.8 | 15 | kΩ | RFRL external resistor value operation range | 7 | |
| Maximum FLASH Frequency (typ) | fmax | 125 | Hz | Derived from RFRL and KFRL(typ); valid for RFRL = 800 Ω | 7 | ||
| KFRL tolerance | tolFRL | -13 | 13 | % | Tolerance of Frame Rate Limit | 7 | |
| Overcurrent protection RFRL (short to ground) | IFRL_lim | 1.3 | mA | Short to ground; resistor detection for RFRL < 750 Ω | 7 | ||
| Open Load protection RFRL | IFRL_open | 57.5 | μA | Open Load detection; resistor detection for RFRL > 17.5 kΩ | 7 | ||
| Open Load Detection Threshold (FB pin) | VOLth | 130 | 150 | 170 | mV | FLASH = High | 7 |
| Open Load Blanking Time | tOLBlank | 10 | 22 | 35 | μs | 7 | |
| Short to GND Detection Threshold (DET pin) | VSGth | 300 | 350 | 400 | mV | FLASH = Low | 7 |
| Short to GND Blanking Time | tSGBlank | 5 | 10 | 15 | μs | 7 | |
| Short to VSTRING Detection Threshold | VSCth | -1.5 | -1.22 | -0.9 | V | FLASH = High; printed as VSTRING − x V (offset from VSTRING) | 7 |
| Short Circuit Blanking Time | tSCBlank | 5 | 10 | 15 | μs | 7 | |
| Input pull-up resistor on DET pin | RDETPull-up | 30 | 120 | 190 | kΩ | Pull-up to VSTRING | 7 |
| VSTRING diagnostic activation threshold | VSTRth | 2 | 2.2 | 2.4 | V | VSTRING voltage | 7 |
| Output low level | VOUTL | 0.2 | 0.4 | V | Fault is present, IDIAG = 0.33 mA | 7 | |
| Continuous supply voltage | Vmax_VS | -0.3 | 40 | V | 5 | ||
| Transient supply voltage (load dump) | Vmax_VS | 40 | V | t < 500 ms, load dump | 5 | ||
| Low Voltage Input pin (FLASH) | Vmax_FLASH | -0.3 | 3.6 | V | 5 | ||
| Output voltage (during Open Load condition) | Vmax_GATE | -0.3 | V | During Open Load condition; max printed as +VS | 5 | ||
| DC voltage on Resistors (RETL, RFRL) | Vmax_RETL, RFRL | -0.3 | 3.6 | V | 5 | ||
| Low Voltage Input pin (FB) | Vmax_FB | -0.3 | 3.6 | V | 5 | ||
| Open Drain pin (DIAG) | Vmax_DIAG | -0.3 | 40 | V | 5 | ||
| High Voltage Input pin (DET, VSTRING) | Vmax_DET, VSTRING | -0.3 | 40 | V | 5 | ||
| Junction Temperature | Tjmax | -40 | 125 | °C | 5 | ||
| Storage Temperature Range | -40 | 150 | °C | 5 | |||
| Ambient Temperature | -40 | 105 | °C | 5 | |||
| Package Thermal Resistance Junction to Ambient | RθJA | 62.5 | °C/W | JEDEC JESD51-7 2S2P, natural convection | 5 | ||
| Package Thermal Resistance Junction to Board | RθJB | 5.5 | °C/W | JEDEC JESD51-7 2S2P, natural convection | 5 | ||
| Package Thermal Resistance Junction to Case (Top) | RθJC | 2.7 | °C/W | JEDEC JESD51-7 2S2P, natural convection | 5 |
CAD (KiCad official)
- Symbol:
NCV7694MW0R2G - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ncv7694mw0r2g-etched.step/ncv7694mw0r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv7694mw0r2g.step/ncv7694mw0r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (18 pp, sha256
e2a244bba65d1e6a, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).