main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ncv7694mw0r2g: viewers · Ray
ncv7694mw0r2g-etched.glb Publish 0.1.0 · Ray
ncv7694mw0r2g-etched.step ncv7694mw0r2g: factory component page (tier=mfr) · Ray
ncv7694mw0r2g-hero.glb ncv7694mw0r2g: hero GLB from the etched model (keeps the MPN mark) · Ray
ncv7694mw0r2g-hero.overlay.json Publish 0.1.0 · Ray
ncv7694mw0r2g.glb Publish 0.1.0 · Ray
ncv7694mw0r2g.kicad_mod Publish 0.1.0 · Ray
ncv7694mw0r2g.kicad_sym Publish 0.1.0 · Ray
ncv7694mw0r2g.lbr Publish 0.1.0 · Ray
ncv7694mw0r2g.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 11 pins · Ray

NCV7694MW0R2G

onsemi · LED Drivers · DFN-10-EP(3x3)

NCV7694MW0R2G from onsemi, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VS power_in Supply voltage of the device; parametric operation is 7 V to 28 V, with continuous supply up to +40 V and load dump transient up to +40 V (t < 500 ms).
2 DIAG output Open-drain diagnostic output that reports Open Load, Short to VSTRING, Short to GND and thermal/undervoltage status; maximum rating is +40 V and output low is 0.4 V max at 0.33 mA when a fault is present.
3 FLASH input Logic input for flash exposure timing, compatible with 1.8 V / 2.8 V logic, rated −0.3 V to +3.6 V, with an internal pull-down of 120 kΩ typical.
4 RETL passive External resistor that sets the maximum exposure time limit (0.8 kΩ to 15 kΩ operating range); DC voltage rating is −0.3 V to +3.6 V.
5 RFRL passive External resistor that sets the maximum frame rate limit (0.8 kΩ to 15 kΩ operating range); DC voltage rating is −0.3 V to +3.6 V.
6 GND power_in Ground reference of the device.
7 FB input Feedback reference input regulated to 300 mV typical, which sets the LED current via R1; rated −0.3 V to +3.6 V and must stay below 0.19 V when the device is not active.
8 GATE output Gate drive for the external MOSFET, with a minimum gate ON voltage of 4.5 V and a pull-down resistance of 5 kΩ to 100 kΩ (30 kΩ typical).
9 DET input LED cathode sense input; during FLASH-on the voltage should be between 0.35 V and (VSTRING − 1.22 V), and the rating is −0.3 V to +40 V.
10 VSTRING input High-voltage input sensing the top of the LED string and enabling Open Load and Short diagnostics above VSTRth of 2.2 V; rated −0.3 V to +40 V.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer onsemi
Package DFN-10-EP(3x3)
Category Display Modules / LED Drivers / Display Drivers
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VS_OP 7 28 V Parametric operation 6
Supply Under-Voltage Lockout (VS rising) VSUV 4 4.5 5 V VS rising 6
Supply Under-Voltage hysteresis VSUVhys 150 300 550 mV 6
Supply Current in normal condition I_VS 4 6 mA VS = 14 V, FLASH = High, IFRL, IETL subtracted 6
Supply Current in normal condition (FLASH low) I_VS 3.8 6 mA VS = 14 V, FLASH = Low, IFRL, IETL subtracted 6
Supply Current in Fault condition I_VSerr 4 6 mA VS = 14 V, FLASH = High, Open Load condition, IFRL, IETL subtracted 6
Thermal Shutdown (TSD) 130 150 170 °C 6
FB Regulation reference VFBref 270 300 330 mV Under Voltage Lockout < VS 6
Gate ON voltage VGATE 4.5 V FB = 220 mV, DET = 1.0 V 6
Propagation Delay FLASH rising to FB ON tON 8 15 μs 50% criterion 6
Propagation Delay FLASH falling to FB OFF tOFF 6.6 15 μs 50% criterion 6
FLASH propagation Delay Delta tpd_delta 1.4 4 μs /(Falling time), (Rising Time)/, 50% criterion 6
Output pull-down resistance RGATE 5 30 100 kΩ 6
Input High Threshold VinH 1.3 1.2 V 6
Input Low Threshold VinL 1.15 1.1 V 6
Input pull-down resistance RFLASH 30 120 190 kΩ 6
RETL external resistor value operation range RETL 0.8 15 kΩ RETL external resistor value operation range 6
Maximum TON time (typ) TONmax 6 ms Derived from RETL and KETL(typ); valid for RETL = 15 kΩ 6
KETL tolerance tolETL -13 13 % Tolerance of Exposure Time Limit 6
Overcurrent protection RETL (short to ground) IETL_lim 1.3 mA Short to ground; resistor detection for RETL < 750 Ω 6
Open Load protection RETL IETL_open 57.5 μA Open Load detection; resistor detection for RETL > 17.5 kΩ 6
FRL resistor operation range RFRL 0.8 15 kΩ RFRL external resistor value operation range 7
Maximum FLASH Frequency (typ) fmax 125 Hz Derived from RFRL and KFRL(typ); valid for RFRL = 800 Ω 7
KFRL tolerance tolFRL -13 13 % Tolerance of Frame Rate Limit 7
Overcurrent protection RFRL (short to ground) IFRL_lim 1.3 mA Short to ground; resistor detection for RFRL < 750 Ω 7
Open Load protection RFRL IFRL_open 57.5 μA Open Load detection; resistor detection for RFRL > 17.5 kΩ 7
Open Load Detection Threshold (FB pin) VOLth 130 150 170 mV FLASH = High 7
Open Load Blanking Time tOLBlank 10 22 35 μs 7
Short to GND Detection Threshold (DET pin) VSGth 300 350 400 mV FLASH = Low 7
Short to GND Blanking Time tSGBlank 5 10 15 μs 7
Short to VSTRING Detection Threshold VSCth -1.5 -1.22 -0.9 V FLASH = High; printed as VSTRING − x V (offset from VSTRING) 7
Short Circuit Blanking Time tSCBlank 5 10 15 μs 7
Input pull-up resistor on DET pin RDETPull-up 30 120 190 kΩ Pull-up to VSTRING 7
VSTRING diagnostic activation threshold VSTRth 2 2.2 2.4 V VSTRING voltage 7
Output low level VOUTL 0.2 0.4 V Fault is present, IDIAG = 0.33 mA 7
Continuous supply voltage Vmax_VS -0.3 40 V 5
Transient supply voltage (load dump) Vmax_VS 40 V t < 500 ms, load dump 5
Low Voltage Input pin (FLASH) Vmax_FLASH -0.3 3.6 V 5
Output voltage (during Open Load condition) Vmax_GATE -0.3 V During Open Load condition; max printed as +VS 5
DC voltage on Resistors (RETL, RFRL) Vmax_RETL, RFRL -0.3 3.6 V 5
Low Voltage Input pin (FB) Vmax_FB -0.3 3.6 V 5
Open Drain pin (DIAG) Vmax_DIAG -0.3 40 V 5
High Voltage Input pin (DET, VSTRING) Vmax_DET, VSTRING -0.3 40 V 5
Junction Temperature Tjmax -40 125 °C 5
Storage Temperature Range -40 150 °C 5
Ambient Temperature -40 105 °C 5
Package Thermal Resistance Junction to Ambient RθJA 62.5 °C/W JEDEC JESD51-7 2S2P, natural convection 5
Package Thermal Resistance Junction to Board RθJB 5.5 °C/W JEDEC JESD51-7 2S2P, natural convection 5
Package Thermal Resistance Junction to Case (Top) RθJC 2.7 °C/W JEDEC JESD51-7 2S2P, natural convection 5

CAD (KiCad official)

  • Symbol: NCV7694MW0R2G
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: ncv7694mw0r2g-etched.step / ncv7694mw0r2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncv7694mw0r2g.step / ncv7694mw0r2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (18 pp, sha256 e2a244bba65d1e6a, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF