Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

AD7761BSTZ

Analog Devices · Analog To Digital Converters (ADCs) · LQFP-64(10x10)

AD7761BSTZ from Analog Devices, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AIN1− input Negative analog input to ADC Channel 1.
2 AIN1+ input Positive analog input to ADC Channel 1.
3 AVSS1A power_in Negative analog supply, nominally 0 V.
4 AVDD1A power_in Analog supply voltage, 5 V ± 10% with respect to AVSS.
5 REF1− input Negative reference terminal for Channel 0 to Channel 3, range AVSS to (AVDD1 − 1 V); decouple to AVSS with a high quality capacitor.
6 REF1+ input Positive reference terminal for Channel 0 to Channel 3, range (AVSS + 1 V) to AVDD1; apply 1 V to
7 AIN2− input Negative analog input to ADC Channel 2.
8 AIN2+ input Positive analog input to ADC Channel 2.
9 AIN3− input Negative analog input to ADC Channel 3.
10 AIN3+ input Positive analog input to ADC Channel 3.
11 FILTER/GPIO4 bidirectional In pin control mode selects filter type (1 = sinc5, 0 = wideband low ripple); in SPI control mode it is GPIO4 and must be set to 1 when a crystal clock is used and the pin is not a GPIO.
12 MODE0/GPIO0 bidirectional In pin control mode sets the mode of operation for all channels (power, DCLK frequency, conversion type); in SPI control mode it is GPIO0.
13 MODE1/GPIO1 bidirectional In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO1.
14 MODE2/GPIO2 bidirectional In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO2.
15 MODE3/GPIO3 bidirectional In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO3.
16 ST0/CS input In pin control mode a Logic 1 places Channel 0 to Channel 3 in standby; in SPI control mode it is the active low chip select.
17 ST1/SCLK input In pin control mode a Logic 1 places Channel 4 to Channel 7 in standby (Channel 4 must be enabled when using an external crystal); in SPI control mode it is the serial clock input.
18 DEC1/SDI input In pin control mode, with DEC0, sets the decimation rate for all channels; in SPI control mode it is the serial data input.
19 DEC0/SDO bidirectional In pin control mode, with DEC1, sets the decimation rate for all channels; in SPI control mode it is the serial data output for register readback.
20 DOUT7 bidirectional Conversion data output 7, synchronous to DCLK and framed by DRDY; acts as a daisy-chain data input when FORMATx = 01, and needs a pull-down to ground when FORMATx is 10 or 11.
21 DOUT6 bidirectional Conversion data output 6, synchronous to DCLK and framed by DRDY; acts as a digital input from another AD7761 in a daisy chain.
22 DOUT5 output Conversion data output 5, synchronous to DCLK and framed by DRDY.
23 DOUT4 output Conversion data output 4, synchronous to DCLK and framed by DRDY.
24 DOUT3 output Conversion data output 3, synchronous to DCLK and framed by DRDY.
25 DOUT2 output Conversion data output 2, synchronous to DCLK and framed by DRDY.
26 DOUT1 output Conversion data output 1, synchronous to DCLK and framed by DRDY.
27 DOUT0 output Conversion data output 0, synchronous to DCLK and framed by DRDY.
28 DCLK output ADC conversion data clock, derived from MCLK, synchronous with DRDY and DOUT0 to DOUT7; unrelated to the control SPI.
29 DRDY output Data ready; periodic signal framing the conversion results from the eight ADCs, synchronous to DCLK and DOUT0 to DOUT7.
30 RESET input Hardware asynchronous reset input; a hard or soft reset is recommended after the device is fully powered up.
31 XTAL1 input Input 1 for crystal or LVDS clock; connect to DGND when CLK_SEL is 0.
32 XTAL2/MCLK input Input 2 for crystal or LVDS clock, or CMOS MCLK input with logic level IOVDD/DGND; set FILTER to Logic 1 for a crystal clock source.
33 DGND power_in Digital ground, nominally 0 V.
34 DREGCAP power_out Digital LDO output; decouple to DGND with a 10 µF low-ESR capacitor (ESR 50 mΩ to 400 mΩ), not for external circuits, and connect to IOVDD for 1.8 V IOVDD operation.
35 IOVDD power_in Digital supply setting logic levels for all interface pins; powers the digital core via the LDO when at least 2.25 V, and is tied to DREGCAP for 1.8 V operation.
36 SYNC_IN input Synchronization input receiving the synchronous signal from SYNC_OUT, used to synchronize AD7761 devices for simultaneous sampling or daisy chain; must be synchronous to the MCLK domain.
37 START input Start signal that synchronizes the AD7761 to other devices and may be asynchronous; tie to Logic 1 through a pull-up resistor if unused.
38 SYNC_OUT output Synchronization output, synchronous to MCLK, operating only when START is used; must be wired to SYNC_IN of this and other synchronized AD7761 devices.
39 AIN7+ input Positive analog input to ADC Channel 7.
40 AIN7− input Negative analog input to ADC Channel 7.
41 AIN6+ input Positive analog input to ADC Channel 6.
42 AIN6− input Negative analog input to ADC Channel 6.
43 REF2+ input Positive reference terminal for Channel 4 to Channel 7, range (AVSS + 1 V) to AVDD1; apply 1 V to
44 REF2− input Negative reference terminal for Channel 4 to Channel 7, range AVSS to (AVDD1 − 1 V); decouple to AVSS with a high quality capacitor.
45 AVDD1B power_in Analog supply voltage, 5 V ± 10% with respect to AVSS.
46 AVSS1B power_in Negative analog supply, nominally 0 V.
47 AIN5+ input Positive analog input to ADC Channel 5.
48 AIN5− input Negative analog input to ADC Channel 5.
49 AIN4+ input Positive analog input to ADC Channel 4.
50 AIN4− input Negative analog input to ADC Channel 4.
51 AVSS2B power_in Negative analog supply, nominally 0 V.
52 REGCAPB power_out Analog LDO regulator output; decouple to AVSS with a 1 µF capacitor.
53 AVDD2B power_in Analog supply voltage, 2 V to 5.5 V with respect to AVSS.
54 AVSS power_in Negative analog supply, nominally 0 V.
55 FORMAT1 input Format selection pin; hardwire it to set the number of DOUTx pins used for conversion data, checked at power-up.
56 FORMAT0 input Format selection pin; hardwire it to set the number of DOUTx pins used for conversion data, checked at power-up.
57 PIN/SPI input Control method select: Logic 0 = pin control mode, Logic 1 = SPI control mode.
58 CLK_SEL input Clock select: 0 = CMOS clock on Pin 32 (Pin 31 to DGND), 1 = crystal or LVDS clock on Pins 31 and 32 (LVDS only in SPI control mode).
59 VCM output Common-mode voltage output of (AVDD1 − AVSS)/2, 2.5 V by default in pin control mode, configurable to 2.5 V, 2.14 V or 1.65 V in SPI mode; use a 50 Ω series resistor with capacitive loads above 0.1 µF.
60 AVDD2A power_in Analog supply voltage, 2 V to 5.5 V with respect to AVSS.
61 REGCAPA power_out Analog LDO regulator output; decouple to AVSS with a 1 µF capacitor.
62 AVSS2A power_in Negative analog supply, nominally 0 V.
63 AIN0− input Negative analog input to ADC Channel 0.
64 AIN0+ input Positive analog input to ADC Channel 0.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package LQFP-64(10x10)
Category Data Converters
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
AVDD1, AVDD2 to AVSS1 -0.3 6.5 V 15
AVDD1 to DGND -0.3 6.5 V 15
IOVDD to DGND -0.3 6.5 V 15
IOVDD, DREGCAP to DGND -0.3 2.25 V IOVDD tied to DREGCAP for 1.8 V operation 15
IOVDD to AVSS -0.3 7.5 V 15
AVSS to DGND -3.25 0.3 V 15
Analog Input Voltage to AVSS -0.3 0.3 V Upper limit printed as AVDD1 + 0.3 V 15
Reference Input Voltage to AVSS -0.3 0.3 V Upper limit printed as AVDD1 + 0.3 V 15
Digital Input Voltage to DGND -0.3 0.3 V Upper limit printed as IOVDD + 0.3 V 15
Digital Output Voltage to DGND -0.3 0.3 V Upper limit printed as IOVDD + 0.3 V 15
Operating Temperature Range -40 105 °C 15
Storage Temperature Range -65 150 °C 15
Pb-Free Soldering Reflow Temperature 260 °C 10 sec to 30 sec 15
Maximum Junction Temperature 150 °C 15
Maximum Package Classification Temperature 260 °C 15
AVDD2 supply voltage AVDD2 2 5.5 V with respect to AVSS 31
IOVDD supply voltage (internal regulator) IOVDD 2.25 3.6 V relative to DGND 31
IOVDD supply voltage (bypassing regulator) IOVDD 1.72 1.88 V relative to DGND, IOVDD tied to DREGCAP 31
AVSS supply voltage AVSS -2.75 0 V relative to DGND 31
Junction-to-ambient thermal resistance θJA 38 °C/W ST-64-2, JEDEC 2P2S board 15
Junction-to-case thermal resistance θJC 9.2 °C/W ST-64-2, JEDEC 2P2S board 15

CAD (KiCad official)

  • Symbol: AD7761BSTZ
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: ad7761bstz-etched.step / ad7761bstz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ad7761bstz.step / ad7761bstz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (75 pp, sha256 114525c88afd23f8, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF