component
AD7761BSTZ
Public Made by Adomby adom
Analog Devices Analog To Digital Converters (ADCs), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownAD7761BSTZ
Analog Devices · Analog To Digital Converters (ADCs) · LQFP-64(10x10)
AD7761BSTZ from Analog Devices, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN1− | input | Negative analog input to ADC Channel 1. |
| 2 | AIN1+ | input | Positive analog input to ADC Channel 1. |
| 3 | AVSS1A | power_in | Negative analog supply, nominally 0 V. |
| 4 | AVDD1A | power_in | Analog supply voltage, 5 V ± 10% with respect to AVSS. |
| 5 | REF1− | input | Negative reference terminal for Channel 0 to Channel 3, range AVSS to (AVDD1 − 1 V); decouple to AVSS with a high quality capacitor. |
| 6 | REF1+ | input | Positive reference terminal for Channel 0 to Channel 3, range (AVSS + 1 V) to AVDD1; apply 1 V to |
| 7 | AIN2− | input | Negative analog input to ADC Channel 2. |
| 8 | AIN2+ | input | Positive analog input to ADC Channel 2. |
| 9 | AIN3− | input | Negative analog input to ADC Channel 3. |
| 10 | AIN3+ | input | Positive analog input to ADC Channel 3. |
| 11 | FILTER/GPIO4 | bidirectional | In pin control mode selects filter type (1 = sinc5, 0 = wideband low ripple); in SPI control mode it is GPIO4 and must be set to 1 when a crystal clock is used and the pin is not a GPIO. |
| 12 | MODE0/GPIO0 | bidirectional | In pin control mode sets the mode of operation for all channels (power, DCLK frequency, conversion type); in SPI control mode it is GPIO0. |
| 13 | MODE1/GPIO1 | bidirectional | In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO1. |
| 14 | MODE2/GPIO2 | bidirectional | In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO2. |
| 15 | MODE3/GPIO3 | bidirectional | In pin control mode sets the mode of operation for all channels; in SPI control mode it is GPIO3. |
| 16 | ST0/CS | input | In pin control mode a Logic 1 places Channel 0 to Channel 3 in standby; in SPI control mode it is the active low chip select. |
| 17 | ST1/SCLK | input | In pin control mode a Logic 1 places Channel 4 to Channel 7 in standby (Channel 4 must be enabled when using an external crystal); in SPI control mode it is the serial clock input. |
| 18 | DEC1/SDI | input | In pin control mode, with DEC0, sets the decimation rate for all channels; in SPI control mode it is the serial data input. |
| 19 | DEC0/SDO | bidirectional | In pin control mode, with DEC1, sets the decimation rate for all channels; in SPI control mode it is the serial data output for register readback. |
| 20 | DOUT7 | bidirectional | Conversion data output 7, synchronous to DCLK and framed by DRDY; acts as a daisy-chain data input when FORMATx = 01, and needs a pull-down to ground when FORMATx is 10 or 11. |
| 21 | DOUT6 | bidirectional | Conversion data output 6, synchronous to DCLK and framed by DRDY; acts as a digital input from another AD7761 in a daisy chain. |
| 22 | DOUT5 | output | Conversion data output 5, synchronous to DCLK and framed by DRDY. |
| 23 | DOUT4 | output | Conversion data output 4, synchronous to DCLK and framed by DRDY. |
| 24 | DOUT3 | output | Conversion data output 3, synchronous to DCLK and framed by DRDY. |
| 25 | DOUT2 | output | Conversion data output 2, synchronous to DCLK and framed by DRDY. |
| 26 | DOUT1 | output | Conversion data output 1, synchronous to DCLK and framed by DRDY. |
| 27 | DOUT0 | output | Conversion data output 0, synchronous to DCLK and framed by DRDY. |
| 28 | DCLK | output | ADC conversion data clock, derived from MCLK, synchronous with DRDY and DOUT0 to DOUT7; unrelated to the control SPI. |
| 29 | DRDY | output | Data ready; periodic signal framing the conversion results from the eight ADCs, synchronous to DCLK and DOUT0 to DOUT7. |
| 30 | RESET | input | Hardware asynchronous reset input; a hard or soft reset is recommended after the device is fully powered up. |
| 31 | XTAL1 | input | Input 1 for crystal or LVDS clock; connect to DGND when CLK_SEL is 0. |
| 32 | XTAL2/MCLK | input | Input 2 for crystal or LVDS clock, or CMOS MCLK input with logic level IOVDD/DGND; set FILTER to Logic 1 for a crystal clock source. |
| 33 | DGND | power_in | Digital ground, nominally 0 V. |
| 34 | DREGCAP | power_out | Digital LDO output; decouple to DGND with a 10 µF low-ESR capacitor (ESR 50 mΩ to 400 mΩ), not for external circuits, and connect to IOVDD for 1.8 V IOVDD operation. |
| 35 | IOVDD | power_in | Digital supply setting logic levels for all interface pins; powers the digital core via the LDO when at least 2.25 V, and is tied to DREGCAP for 1.8 V operation. |
| 36 | SYNC_IN | input | Synchronization input receiving the synchronous signal from SYNC_OUT, used to synchronize AD7761 devices for simultaneous sampling or daisy chain; must be synchronous to the MCLK domain. |
| 37 | START | input | Start signal that synchronizes the AD7761 to other devices and may be asynchronous; tie to Logic 1 through a pull-up resistor if unused. |
| 38 | SYNC_OUT | output | Synchronization output, synchronous to MCLK, operating only when START is used; must be wired to SYNC_IN of this and other synchronized AD7761 devices. |
| 39 | AIN7+ | input | Positive analog input to ADC Channel 7. |
| 40 | AIN7− | input | Negative analog input to ADC Channel 7. |
| 41 | AIN6+ | input | Positive analog input to ADC Channel 6. |
| 42 | AIN6− | input | Negative analog input to ADC Channel 6. |
| 43 | REF2+ | input | Positive reference terminal for Channel 4 to Channel 7, range (AVSS + 1 V) to AVDD1; apply 1 V to |
| 44 | REF2− | input | Negative reference terminal for Channel 4 to Channel 7, range AVSS to (AVDD1 − 1 V); decouple to AVSS with a high quality capacitor. |
| 45 | AVDD1B | power_in | Analog supply voltage, 5 V ± 10% with respect to AVSS. |
| 46 | AVSS1B | power_in | Negative analog supply, nominally 0 V. |
| 47 | AIN5+ | input | Positive analog input to ADC Channel 5. |
| 48 | AIN5− | input | Negative analog input to ADC Channel 5. |
| 49 | AIN4+ | input | Positive analog input to ADC Channel 4. |
| 50 | AIN4− | input | Negative analog input to ADC Channel 4. |
| 51 | AVSS2B | power_in | Negative analog supply, nominally 0 V. |
| 52 | REGCAPB | power_out | Analog LDO regulator output; decouple to AVSS with a 1 µF capacitor. |
| 53 | AVDD2B | power_in | Analog supply voltage, 2 V to 5.5 V with respect to AVSS. |
| 54 | AVSS | power_in | Negative analog supply, nominally 0 V. |
| 55 | FORMAT1 | input | Format selection pin; hardwire it to set the number of DOUTx pins used for conversion data, checked at power-up. |
| 56 | FORMAT0 | input | Format selection pin; hardwire it to set the number of DOUTx pins used for conversion data, checked at power-up. |
| 57 | PIN/SPI | input | Control method select: Logic 0 = pin control mode, Logic 1 = SPI control mode. |
| 58 | CLK_SEL | input | Clock select: 0 = CMOS clock on Pin 32 (Pin 31 to DGND), 1 = crystal or LVDS clock on Pins 31 and 32 (LVDS only in SPI control mode). |
| 59 | VCM | output | Common-mode voltage output of (AVDD1 − AVSS)/2, 2.5 V by default in pin control mode, configurable to 2.5 V, 2.14 V or 1.65 V in SPI mode; use a 50 Ω series resistor with capacitive loads above 0.1 µF. |
| 60 | AVDD2A | power_in | Analog supply voltage, 2 V to 5.5 V with respect to AVSS. |
| 61 | REGCAPA | power_out | Analog LDO regulator output; decouple to AVSS with a 1 µF capacitor. |
| 62 | AVSS2A | power_in | Negative analog supply, nominally 0 V. |
| 63 | AIN0− | input | Negative analog input to ADC Channel 0. |
| 64 | AIN0+ | input | Positive analog input to ADC Channel 0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-64(10x10) |
| Category | Data Converters |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| AVDD1, AVDD2 to AVSS1 | -0.3 | 6.5 | V | 15 | |||
| AVDD1 to DGND | -0.3 | 6.5 | V | 15 | |||
| IOVDD to DGND | -0.3 | 6.5 | V | 15 | |||
| IOVDD, DREGCAP to DGND | -0.3 | 2.25 | V | IOVDD tied to DREGCAP for 1.8 V operation | 15 | ||
| IOVDD to AVSS | -0.3 | 7.5 | V | 15 | |||
| AVSS to DGND | -3.25 | 0.3 | V | 15 | |||
| Analog Input Voltage to AVSS | -0.3 | 0.3 | V | Upper limit printed as AVDD1 + 0.3 V | 15 | ||
| Reference Input Voltage to AVSS | -0.3 | 0.3 | V | Upper limit printed as AVDD1 + 0.3 V | 15 | ||
| Digital Input Voltage to DGND | -0.3 | 0.3 | V | Upper limit printed as IOVDD + 0.3 V | 15 | ||
| Digital Output Voltage to DGND | -0.3 | 0.3 | V | Upper limit printed as IOVDD + 0.3 V | 15 | ||
| Operating Temperature Range | -40 | 105 | °C | 15 | |||
| Storage Temperature Range | -65 | 150 | °C | 15 | |||
| Pb-Free Soldering Reflow Temperature | 260 | °C | 10 sec to 30 sec | 15 | |||
| Maximum Junction Temperature | 150 | °C | 15 | ||||
| Maximum Package Classification Temperature | 260 | °C | 15 | ||||
| AVDD2 supply voltage | AVDD2 | 2 | 5.5 | V | with respect to AVSS | 31 | |
| IOVDD supply voltage (internal regulator) | IOVDD | 2.25 | 3.6 | V | relative to DGND | 31 | |
| IOVDD supply voltage (bypassing regulator) | IOVDD | 1.72 | 1.88 | V | relative to DGND, IOVDD tied to DREGCAP | 31 | |
| AVSS supply voltage | AVSS | -2.75 | 0 | V | relative to DGND | 31 | |
| Junction-to-ambient thermal resistance | θJA | 38 | °C/W | ST-64-2, JEDEC 2P2S board | 15 | ||
| Junction-to-case thermal resistance | θJC | 9.2 | °C/W | ST-64-2, JEDEC 2P2S board | 15 |
CAD (KiCad official)
- Symbol:
AD7761BSTZ - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
ad7761bstz-etched.step/ad7761bstz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7761bstz.step/ad7761bstz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (75 pp, sha256
114525c88afd23f8, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).