3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT1965EMS8E#PBF
Analog Devices · Linear Voltage Regulators (LDO) · MSOP-8-EP
LT1965EMS8E#PBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output pin supplying power to the load; requires a minimum 10µF output capacitor to prevent oscillations. |
| 2 | OUT | power_out | Output pin supplying power to the load; requires a minimum 10µF output capacitor to prevent oscillations (tied internally with pin 1). |
| 3 | ADJ | input | Adjust pin (LT1965 adjustable version) is the error amplifier input, held at 1.20V referenced to ground with typical 1.3µA bias current flowing into the pin. |
| 4 | GND | power_in | Ground; for the adjustable LT1965 connect the bottom of the output-setting resistor divider directly to GND. |
| 5 | GND | power_in | Ground; tie directly to pin 4, the exposed pad and PCB ground. |
| 6 | SHDN | input | Shutdown; pulling low turns the output off (<1µA quiescent), pin current typically less than 5.5µA, connect to VIN if unused, and do not drive below GND unless tied to IN. |
| 7 | IN | power_in | Input supply pin (1.8V to 20V range, ±22V abs max) that needs a 1µF to 10µF bypass capacitor if more than six inches from the main input filter capacitor; withstands reverse voltage. |
| 8 | IN | power_in | Input supply pin (tied internally with pin 7) that needs a 1µF to 10µF bypass capacitor if located far from the main input filter capacitor. |
| 9 | EP | power_in | Exposed pad is ground, must be soldered to the PCB and tied directly to pins 4 and 5 for enhanced thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8-EP |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| ADJ Pin Voltage | VADJ | 1.182 | 1.2 | 1.218 | V | VIN = 2.1V, ILOAD = 1mA | 4 |
| ADJ Pin Voltage | VADJ | 1.164 | 1.2 | 1.236 | V | 2.3V < VIN < 20V, 1mA < ILOAD < 1.1A (TJ < 125°C) | 4 |
| Line Regulation | 3 | 8 | mV | LT1965, ΔVIN = 2.1V to 20V, ILOAD = 1mA (E-, I-Grades) | 4 | ||
| Load Regulation | 4.25 | 8 | mV | LT1965, VIN = 2.3V, ΔILOAD = 1mA to 1.1A | 4 | ||
| Load Regulation | 16 | mV | LT1965, VIN = 2.3V, ΔILOAD = 1mA to 1.1A (TJ < 125°C) | 4 | |||
| Dropout Voltage | 0.055 | 0.08 | V | ILOAD = 1mA | 4 | ||
| Dropout Voltage | 0.14 | V | ILOAD = 1mA, full temperature range | 4 | |||
| Dropout Voltage | 0.12 | 0.175 | V | ILOAD = 100mA | 4 | ||
| Dropout Voltage | 0.28 | V | ILOAD = 100mA, full temperature range | 4 | |||
| Dropout Voltage | 0.21 | 0.25 | V | ILOAD = 500mA | 4 | ||
| Dropout Voltage | 0.36 | V | ILOAD = 500mA, full temperature range | 4 | |||
| Dropout Voltage | 0.31 | 0.36 | V | ILOAD = 1.1A | 4 | ||
| Dropout Voltage | 0.49 | V | ILOAD = 1.1A (TJ < 125°C) | 4 | |||
| GND Pin Current | 0.5 | 1.1 | mA | VIN = VOUT(NOMINAL) + 1V, ILOAD = 0mA | 4 | ||
| GND Pin Current | 0.6 | 1.5 | mA | VIN = VOUT(NOMINAL) + 1V, ILOAD = 1mA | 4 | ||
| GND Pin Current | 2.2 | 5.5 | mA | VIN = VOUT(NOMINAL) + 1V, ILOAD = 100mA | 4 | ||
| GND Pin Current | 8.2 | 20 | mA | VIN = VOUT(NOMINAL) + 1V, ILOAD = 500mA | 4 | ||
| GND Pin Current | 21 | 40 | mA | VIN = VOUT(NOMINAL) + 1V, ILOAD = 1.1A (TJ < 125°C) | 4 | ||
| ADJ Pin Bias Current | 1.3 | 4.5 | µA | Notes 4, 9 | 4 | ||
| Shutdown Threshold (On to Off) | 0.2 | 0.45 | V | VOUT = On to Off | 4 | ||
| Shutdown Threshold (Off to On) | 0.85 | 2 | V | VOUT = Off to On | 4 | ||
| SHDN Pin Current | 0.01 | 1 | µA | VSHDN = 0V | 5 | ||
| SHDN Pin Current | 5.5 | 10 | µA | VSHDN = 20V | 5 | ||
| Quiescent Current in Shutdown | 0.01 | 1 | µA | VIN = 6V, VSHDN = 0V | 5 | ||
| Ripple Rejection | 57 | 75 | dB | VIN, VOUT = 1.5V (AVG), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A | 5 | ||
| Current Limit | 1.2 | A | VIN = VOUT(NOMINAL) + 1V, ΔVOUT = -0.1V (TJ < 125°C) (Note 6) | 5 | |||
| Current Limit | 2.4 | A | VIN = 7V, VOUT = 0 | 5 | |||
| Input Reverse-Leakage Current | 1 | mA | VIN = -20V, VOUT = 0 | 5 | |||
| Reverse-Output Current | 175 | 400 | µA | LT1965 (Note 4), VOUT = 1.2V, VIN = 0 | 5 | ||
| Minimum Input Voltage | 1.65 | V | ILOAD = 0.5A | 4 | |||
| Minimum Input Voltage | 1.8 | 2.3 | V | ILOAD = 1.1A (TJ < 125°C) | 4 | ||
| Output Voltage Noise | 40 | µVRMS | COUT = 10µF, ILOAD = 1.1A, BW = 10Hz to 100kHz | 4 | |||
| IN Pin Voltage | -22 | 22 | V | 2 | |||
| OUT Pin Voltage | -22 | 22 | V | 2 | |||
| Input to Output Differential Voltage | -22 | 22 | V | Note 2 | 2 | ||
| SENSE Pin Voltage | -22 | 22 | V | 2 | |||
| ADJ Pin Voltage | -9 | 9 | V | 2 | |||
| SHDN Pin Voltage | -22 | 22 | V | 2 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | E-, I-Grades (Notes 3, 5, 13) | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature | TJMAX | 125 | °C | MS8E package | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 60 | °C/W | MS8E package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 10 | °C/W | MS8E package | 2 |
CAD (KiCad official)
- Symbol:
LT1965EMS8E#PBF - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lt1965ems8e-pbf-etched.step/lt1965ems8e-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1965ems8e-pbf.step/lt1965ems8e-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
070eb5a9c32d091a, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).