Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TMS320LF2406APZAR

Texas Instruments · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)

TMS320LF2406APZAR from Texas Instruments, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TRST input JTAG test reset with internal pulldown; it must be maintained low during normal device operation and pullup resistors must not be used on it.
2 TDIRB/IOPF4 bidirectional Counting direction input for the EVB general-purpose timer or GPIO; TDIRB = 1 selects upward counting and TDIRB = 0 selects downward counting.
3 VSSO power_in I/O buffer ground and digital logic/buffer ground reference; all power supply pins must be connected for proper operation.
4 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
5 T4PWM/T4CMP/IOPF3 bidirectional Timer 4 compare output (EVB) or GPIO.
6 PDPINTA input Power drive protection interrupt input that places the EVA PWM outputs in high impedance on motor drive/power converter abnormalities such as overvoltage or overcurrent; it is falling-edge sensitive.
7 T3PWM/T3CMP/IOPF2 bidirectional Timer 3 compare output (EVB) or GPIO.
8 PLLF2 passive PLL loop filter input 2, connected to the external loop filter circuit (R1, C1, C2).
9 PLLF passive PLL loop filter input 1, connected to the external loop filter circuit (R1, C1, C2).
10 PLLVCCA power_in PLL supply, 3.3 V.
11 TDIRA/IOPB6 bidirectional Counting direction input for the EVA general-purpose timer or GPIO; TDIRA = 1 selects upward counting and TDIRA = 0 selects downward counting.
12 T1PWM/T1CMP/IOPB4 bidirectional Timer 1 compare output (EVA) or GPIO.
13 T2PWM/T2CMP/IOPB5 bidirectional Timer 2 compare output (EVA) or GPIO.
14 IOPC0 bidirectional General-purpose I/O (shared with W/R); on the 2406A, W/R mode is not functional, so MCRB.0 must be set to 0 before the pin is used as IOPC0.
15 XINT2/ADCSOC/IOPD0 bidirectional External user interrupt 2 and external ADC start-of-conversion input, or GPIO; edge-sensitive with programmable polarity.
16 XINT1/IOPA2 bidirectional External user interrupt 1 or GPIO; edge-sensitive with programmable polarity.
17 SCITXD/IOPA0 bidirectional SCI asynchronous serial port transmit data or GPIO.
18 SCIRXD/IOPA1 bidirectional SCI asynchronous serial port receive data or GPIO.
19 VSS power_in Core ground, digital logic ground reference.
20 VDD power_in Core supply, +3.3 V digital logic supply voltage.
21 SPISIMO/IOPC2 bidirectional SPI slave in, master out, or GPIO.
22 SPISOMI/IOPC3 bidirectional SPI slave out, master in, or GPIO.
23 SPISTE/IOPC5 bidirectional SPI slave transmit enable (optional) or GPIO.
24 SPICLK/IOPC4 bidirectional SPI clock or GPIO.
25 TMS2 input JTAG test-mode select 2 with internal pullup, for test and emulation only; it may be left unconnected in user applications, and if PLL bypass is desired TMS2, TMS and TRST must be held low during reset.
26 TCLKINA/IOPB7 bidirectional External clock input for the EVA general-purpose timer or GPIO; the timer can also use the internal device clock.
27 PWM12/IOPE6 bidirectional Compare/PWM output pin #12 (EVB) or GPIO.
28 PWM6/IOPB3 bidirectional Compare/PWM output pin #6 (EVA) or GPIO.
29 VSSO power_in I/O buffer ground, digital logic and buffer ground reference.
30 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
31 PWM5/IOPB2 bidirectional Compare/PWM output pin #5 (EVA) or GPIO.
32 PWM11/IOPE5 bidirectional Compare/PWM output pin #11 (EVB) or GPIO.
33 PWM4/IOPB1 bidirectional Compare/PWM output pin #4 (EVA) or GPIO.
34 VSS power_in Core ground, digital logic ground reference.
35 VDD power_in Core supply, +3.3 V digital logic supply voltage.
36 PWM3/IOPB0 bidirectional Compare/PWM output pin #3 (EVA) or GPIO.
37 PWM2/IOPA7 bidirectional Compare/PWM output pin #2 (EVA) or GPIO.
38 PWM10/IOPE4 bidirectional Compare/PWM output pin #10 (EVB) or GPIO.
39 PWM1/IOPA6 bidirectional Compare/PWM output pin #1 (EVA) or GPIO.
40 VCCP (5V) power_in Flash programming voltage; must be connected to a 5-V supply for Flash programming, may be tied to 5 V or GND during normal operation, must not be left floating, and no current-limiting resistor may be used in series.
41 PWM9/IOPE3 bidirectional Compare/PWM output pin #9 (EVB) or GPIO.
42 TP1 unconnected Test pin 1; do not connect.
43 PWM8/IOPE2 bidirectional Compare/PWM output pin #8 (EVB) or GPIO.
44 TP2 unconnected Test pin 2; do not connect.
45 PWM7/IOPE1 bidirectional Compare/PWM output pin #7 (EVB) or GPIO.
46 VSSO power_in I/O buffer ground, digital logic and buffer ground reference.
47 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
48 CAP6/IOPF1 bidirectional Capture input #6 (EVB) or GPIO.
49 CANRX/IOPC7 bidirectional CAN receive data or GPIO.
50 CANTX/IOPC6 bidirectional CAN transmit data or GPIO.
51 CLKOUT/IOPE0 bidirectional Clock output (CPU CLKOUT or watchdog clock WDCLK, selected by the CLKSRC bit of SCSR) or GPIO.
52 CAP3/IOPA5 bidirectional Capture input #3 (EVA) or GPIO.
53 VSSO power_in I/O buffer ground, digital logic and buffer ground reference.
54 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
55 CAP2/QEP2/IOPA4 bidirectional Capture input #2 / quadrature encoder pulse input #2 (EVA) or GPIO.
56 CAP5/QEP4/IOPF0 bidirectional Capture input #5 / quadrature encoder pulse input #4 (EVB) or GPIO.
57 CAP1/QEP1/IOPA3 bidirectional Capture input #1 / quadrature encoder pulse input #1 (EVA) or GPIO.
58 VSS power_in Core ground, digital logic ground reference.
59 VDD power_in Core supply, +3.3 V digital logic supply voltage.
60 CAP4/QEP3/IOPE7 bidirectional Capture input #4 / quadrature encoder pulse input #3 (EVB) or GPIO.
61 EMU0 bidirectional Emulator I/O #0 with internal pullup; when TRST is driven high it is used as an interrupt to or from the emulator and is defined as input/output through the JTAG scan.
62 EMU1/OFF bidirectional Emulator pin 1 with internal pullup; when TRST is driven low this pin is configured as OFF, and when active low it puts all output drivers in the high-impedance state (testing and emulation only).
63 VSSO power_in I/O buffer ground, digital logic and buffer ground reference.
64 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
65 ADCIN15 input Analog input #15 to the ADC.
66 ADCIN07 input Analog input #7 to the ADC.
67 ADCIN06 input Analog input #6 to the ADC.
68 ADCIN14 input Analog input #14 to the ADC.
69 ADCIN05 input Analog input #5 to the ADC.
70 ADCIN04 input Analog input #4 to the ADC.
71 ADCIN13 input Analog input #13 to the ADC.
72 ADCIN03 input Analog input #3 to the ADC.
73 ADCIN12 input Analog input #12 to the ADC.
74 ADCIN02 input Analog input #2 to the ADC.
75 ADCIN11 input Analog input #11 to the ADC.
76 ADCIN10 input Analog input #10 to the ADC.
77 ADCIN01 input Analog input #1 to the ADC.
78 ADCIN09 input Analog input #9 to the ADC.
79 ADCIN00 input Analog input #0 to the ADC.
80 ADCIN08 input Analog input #8 to the ADC.
81 VREFLO input ADC analog low-voltage reference input.
82 VREFHI input ADC analog high-voltage reference input.
83 VCCA power_in Analog supply voltage for the ADC, 3.3 V; it is highly recommended to isolate VCCA from the digital supply for ADC accuracy and noise immunity.
84 VSSA power_in Analog ground reference for the ADC; it is highly recommended to isolate VSSA from digital ground.
85 BIO/IOPC1 bidirectional Branch control input polled by the BCND instruction (branch executed if low); if not used it should be pulled high, and it can be used as GPIO if not used as branch control input.
86 BOOT_EN/XF bidirectional Boot ROM enable sampled as input during reset, then driven as the XF output (driven high after reset); it must be driven with a passive circuit only.
87 XTAL1/CLKIN input PLL oscillator input: crystal input or clock source input to the PLL, with input frequency 4-20 MHz for crystal or external clock with PLL.
88 XTAL2 output Crystal output (PLL oscillator output); it goes to the high-impedance state when EMU1/OFF is active low.
89 TCLKINB/IOPF5 bidirectional External clock input for the EVB general-purpose timer or GPIO; the timer can also use the internal device clock.
90 VSS power_in Core ground, digital logic ground reference.
91 VDD power_in Core supply, +3.3 V digital logic supply voltage.
92 IOPF6 bidirectional General-purpose I/O pin with internal pullup.
93 RS bidirectional Device reset input and watchdog reset output (open-drain with 20 µA typical internal pullup); it is recommended to drive it with an open-drain device, and it is driven low for 128 CLKIN cycles during a watchdog reset.
94 TCK input JTAG test clock with internal pullup.
95 PDPINTB input Power drive protection interrupt input that places the EVB PWM outputs in high impedance on motor drive/power converter abnormalities; it is falling-edge sensitive.
96 TDI input JTAG test data input with internal pullup; clocked into the selected register on a rising edge of TCK.
97 VSSO power_in I/O buffer ground, digital logic and buffer ground reference.
98 VDDO power_in I/O buffer supply, +3.3 V digital logic and buffer supply voltage.
99 TDO output JTAG scan out; the contents of the selected register are shifted out on the falling edge of TCK.
100 TMS input JTAG test-mode select with internal pullup; clocked into the TAP controller on the rising edge of TCK.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package LQFP-100(14x14)
Category Single Chip Microcomputer/Microcontroller
Pins 100

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD, PLLVCCA, VDDO, VCCA VDD -0.3 4.6 V with respect to VSS 71
VCCP range VCCP -0.3 5.5 V 71
Input voltage range VIN -0.3 4.6 V 71
Output voltage range, LF240xA VO -0.3 4.6 V LF240xA 71
Input clamp current IIK -20 20 mA VIN < 0 or VIN > VCC 71
Output clamp current IOK -20 20 mA VO < 0 or VO > VCC 71
Operating free-air temperature, A version TA -40 85 °C A version 71
Junction temperature range TJ -40 150 °C 71
Storage temperature range Tstg -65 150 °C 71
Supply voltage VDD/VDDO VDD 3 3.3 3.6 V VDDO = VDD ± 0.3 V 71
PLL supply voltage PLLVCCA 3 3.3 3.6 V 71
ADC supply voltage VCCA 3 3.3 3.6 V VCCA should not differ from VDD by more than 0.3 V 71
Flash programming supply voltage VCCP 4.75 5 5.25 V 71
Device clock frequency (system clock) fCLKOUT 2 40 MHz 71
High level input voltage VIH 2 V All inputs 71
High-level output source current, Group 1 IOH -2 mA Output pins Group 1; VOH = 2.4 V 71
High-level output source current, Group 2 IOH -4 mA Output pins Group 2; VOH = 2.4 V 71
High-level output source current, Group 3 IOH -8 mA Output pins Group 3; VOH = 2.4 V 71
Low-level output sink current, Group 1 IOL 2 mA Output pins Group 1; VOL = VOL MAX 71
Low-level output sink current, Group 2 IOL 4 mA Output pins Group 2; VOL = VOL MAX 71
Low-level output sink current, Group 3 IOL 8 mA Output pins Group 3; VOL = VOL MAX 71
Junction temperature TJ -40 25 150 °C 71
High-level output voltage VOH 2.4 V VDD = 3.0 V, IOH = IOHMAX 72
Low-level output voltage VOL 0.4 V IOL = IOLMAX 72
Input current (low level), with pullup IIL -10 -16 -30 µA With pullup; VDD = 3.3 V, VIN = 0 V 72
Input current (low level), with pulldown IIL -2 2 µA With pulldown; VDD = 3.3 V, VIN = 0 V 72
Input current (high level), with pullup IIH -2 2 µA With pullup; VDD = 3.3 V, VIN = VDD 72
Input current (high level), with pulldown IIH 10 16 30 µA With pulldown; VDD = 3.3 V, VIN = VDD 72
Leakage current, high-impedance state (off-state) IOZ -2 2 µA VO = VDD or 0 V 72
Input capacitance Ci 2 pF 72
Output capacitance Co 3 pF 72
Operational current, LF2406A IDD 95 120 mA 40-MHz CLKOUT; test code in B0 RAM; all I/O pins floating 72
ADC module current, LF2406A ICCA 10 22 mA 72
Operational current, LPM0, LF2406A IDD 70 80 mA LPM0; clock to all peripherals is enabled 73
ADC module current, LPM0, LF2406A ICCA 10 22 mA LPM0; clock to all peripherals is enabled; no I/O pins are switching 73
Operational current, LPM1, LF2406A IDD 35 45 mA LPM1; clock to all peripherals is disabled 73
ADC module current, LPM1, LF2406A ICCA 0 0 mA LPM1; clock to all peripherals is disabled; no I/O pins are switching 73
Operational current, LPM2, LF2406A IDD 200 400 µA LPM2; clock to all peripherals is disabled; Flash is powered down 73
ADC module current, LPM2, LF2406A ICCA 0 0 mA LPM2; Flash is powered down; input clock is disabled 73
ADC analog input reference current IADREFHI 0.75 1.5 mA 108
Analog input leakage IADCIN 1 µA 108
ADC operating frequency 4 30 MHz 107
Differential nonlinearity error EDNL 2 LSB CLKOUT 30 MHz; VREFHI = VCCA, VREFLO = VSSA 108
Integral nonlinearity error EINL 2 LSB CLKOUT 30 MHz; VREFHI = VCCA, VREFLO = VSSA 108
Cycle time, ADC prescaled clock tc(AD) 33.3 ns 109
Input clock frequency, resonator fx 4 13 MHz Resonator 80
Input clock frequency, crystal fx 4 20 MHz Crystal 80
Cycle time, CLKOUT ×4 mode tc(CO) 25 ns PLL ×4 mode 80
Fall time, CLKOUT tf(CO) 4 ns 80
Rise time, CLKOUT tr(CO) 4 ns 80
Cycle time, XTAL1/CLKIN tc(Cl) 250 ns 80
Fall time, XTAL1/CLKIN tf(Cl) 5 ns 80
Rise time, XTAL1/CLKIN tr(Cl) 5 ns 80
Pulse duration, XTAL1/CLKIN low as % of tc(Cl) tw(CIL) 40 60 % 80
Pulse duration, XTAL1/CLKIN high as % of tc(Cl) tw(CIH) 40 60 % 80
Junction-to-ambient thermal resistance, PZ package ΘJA 42 °C/W PZ package, typical 126
Junction-to-case thermal resistance, PZ package ΘJC 8 °C/W PZ package, typical 126
Junction-to-top of package thermal characterization, PZ package Ψjt 0.5 °C/W PZ package, typical 126

CAD (KiCad official)

  • Symbol: TMS320LF2406APZAR
  • Footprint: Package_QFP:LQFP-100_14x14mm_P0.5mm
  • 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
  • 3D model files: tms320lf2406apzar-etched.step / tms320lf2406apzar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tms320lf2406apzar.step / tms320lf2406apzar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (141 pp, sha256 f19019cb4a75676b, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF