component
TMS320LF2406APZAR
Public Made by Adomby adom
Texas Instruments Microcontroller Units (MCUs/MPUs/SOCs), LQFP-100(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTMS320LF2406APZAR
Texas Instruments · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)
TMS320LF2406APZAR from Texas Instruments, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TRST | input | JTAG test reset with internal pulldown; it must be maintained low during normal device operation and pullup resistors must not be used on it. |
| 2 | TDIRB/IOPF4 | bidirectional | Counting direction input for the EVB general-purpose timer or GPIO; TDIRB = 1 selects upward counting and TDIRB = 0 selects downward counting. |
| 3 | VSSO | power_in | I/O buffer ground and digital logic/buffer ground reference; all power supply pins must be connected for proper operation. |
| 4 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 5 | T4PWM/T4CMP/IOPF3 | bidirectional | Timer 4 compare output (EVB) or GPIO. |
| 6 | PDPINTA | input | Power drive protection interrupt input that places the EVA PWM outputs in high impedance on motor drive/power converter abnormalities such as overvoltage or overcurrent; it is falling-edge sensitive. |
| 7 | T3PWM/T3CMP/IOPF2 | bidirectional | Timer 3 compare output (EVB) or GPIO. |
| 8 | PLLF2 | passive | PLL loop filter input 2, connected to the external loop filter circuit (R1, C1, C2). |
| 9 | PLLF | passive | PLL loop filter input 1, connected to the external loop filter circuit (R1, C1, C2). |
| 10 | PLLVCCA | power_in | PLL supply, 3.3 V. |
| 11 | TDIRA/IOPB6 | bidirectional | Counting direction input for the EVA general-purpose timer or GPIO; TDIRA = 1 selects upward counting and TDIRA = 0 selects downward counting. |
| 12 | T1PWM/T1CMP/IOPB4 | bidirectional | Timer 1 compare output (EVA) or GPIO. |
| 13 | T2PWM/T2CMP/IOPB5 | bidirectional | Timer 2 compare output (EVA) or GPIO. |
| 14 | IOPC0 | bidirectional | General-purpose I/O (shared with W/R); on the 2406A, W/R mode is not functional, so MCRB.0 must be set to 0 before the pin is used as IOPC0. |
| 15 | XINT2/ADCSOC/IOPD0 | bidirectional | External user interrupt 2 and external ADC start-of-conversion input, or GPIO; edge-sensitive with programmable polarity. |
| 16 | XINT1/IOPA2 | bidirectional | External user interrupt 1 or GPIO; edge-sensitive with programmable polarity. |
| 17 | SCITXD/IOPA0 | bidirectional | SCI asynchronous serial port transmit data or GPIO. |
| 18 | SCIRXD/IOPA1 | bidirectional | SCI asynchronous serial port receive data or GPIO. |
| 19 | VSS | power_in | Core ground, digital logic ground reference. |
| 20 | VDD | power_in | Core supply, +3.3 V digital logic supply voltage. |
| 21 | SPISIMO/IOPC2 | bidirectional | SPI slave in, master out, or GPIO. |
| 22 | SPISOMI/IOPC3 | bidirectional | SPI slave out, master in, or GPIO. |
| 23 | SPISTE/IOPC5 | bidirectional | SPI slave transmit enable (optional) or GPIO. |
| 24 | SPICLK/IOPC4 | bidirectional | SPI clock or GPIO. |
| 25 | TMS2 | input | JTAG test-mode select 2 with internal pullup, for test and emulation only; it may be left unconnected in user applications, and if PLL bypass is desired TMS2, TMS and TRST must be held low during reset. |
| 26 | TCLKINA/IOPB7 | bidirectional | External clock input for the EVA general-purpose timer or GPIO; the timer can also use the internal device clock. |
| 27 | PWM12/IOPE6 | bidirectional | Compare/PWM output pin #12 (EVB) or GPIO. |
| 28 | PWM6/IOPB3 | bidirectional | Compare/PWM output pin #6 (EVA) or GPIO. |
| 29 | VSSO | power_in | I/O buffer ground, digital logic and buffer ground reference. |
| 30 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 31 | PWM5/IOPB2 | bidirectional | Compare/PWM output pin #5 (EVA) or GPIO. |
| 32 | PWM11/IOPE5 | bidirectional | Compare/PWM output pin #11 (EVB) or GPIO. |
| 33 | PWM4/IOPB1 | bidirectional | Compare/PWM output pin #4 (EVA) or GPIO. |
| 34 | VSS | power_in | Core ground, digital logic ground reference. |
| 35 | VDD | power_in | Core supply, +3.3 V digital logic supply voltage. |
| 36 | PWM3/IOPB0 | bidirectional | Compare/PWM output pin #3 (EVA) or GPIO. |
| 37 | PWM2/IOPA7 | bidirectional | Compare/PWM output pin #2 (EVA) or GPIO. |
| 38 | PWM10/IOPE4 | bidirectional | Compare/PWM output pin #10 (EVB) or GPIO. |
| 39 | PWM1/IOPA6 | bidirectional | Compare/PWM output pin #1 (EVA) or GPIO. |
| 40 | VCCP (5V) | power_in | Flash programming voltage; must be connected to a 5-V supply for Flash programming, may be tied to 5 V or GND during normal operation, must not be left floating, and no current-limiting resistor may be used in series. |
| 41 | PWM9/IOPE3 | bidirectional | Compare/PWM output pin #9 (EVB) or GPIO. |
| 42 | TP1 | unconnected | Test pin 1; do not connect. |
| 43 | PWM8/IOPE2 | bidirectional | Compare/PWM output pin #8 (EVB) or GPIO. |
| 44 | TP2 | unconnected | Test pin 2; do not connect. |
| 45 | PWM7/IOPE1 | bidirectional | Compare/PWM output pin #7 (EVB) or GPIO. |
| 46 | VSSO | power_in | I/O buffer ground, digital logic and buffer ground reference. |
| 47 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 48 | CAP6/IOPF1 | bidirectional | Capture input #6 (EVB) or GPIO. |
| 49 | CANRX/IOPC7 | bidirectional | CAN receive data or GPIO. |
| 50 | CANTX/IOPC6 | bidirectional | CAN transmit data or GPIO. |
| 51 | CLKOUT/IOPE0 | bidirectional | Clock output (CPU CLKOUT or watchdog clock WDCLK, selected by the CLKSRC bit of SCSR) or GPIO. |
| 52 | CAP3/IOPA5 | bidirectional | Capture input #3 (EVA) or GPIO. |
| 53 | VSSO | power_in | I/O buffer ground, digital logic and buffer ground reference. |
| 54 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 55 | CAP2/QEP2/IOPA4 | bidirectional | Capture input #2 / quadrature encoder pulse input #2 (EVA) or GPIO. |
| 56 | CAP5/QEP4/IOPF0 | bidirectional | Capture input #5 / quadrature encoder pulse input #4 (EVB) or GPIO. |
| 57 | CAP1/QEP1/IOPA3 | bidirectional | Capture input #1 / quadrature encoder pulse input #1 (EVA) or GPIO. |
| 58 | VSS | power_in | Core ground, digital logic ground reference. |
| 59 | VDD | power_in | Core supply, +3.3 V digital logic supply voltage. |
| 60 | CAP4/QEP3/IOPE7 | bidirectional | Capture input #4 / quadrature encoder pulse input #3 (EVB) or GPIO. |
| 61 | EMU0 | bidirectional | Emulator I/O #0 with internal pullup; when TRST is driven high it is used as an interrupt to or from the emulator and is defined as input/output through the JTAG scan. |
| 62 | EMU1/OFF | bidirectional | Emulator pin 1 with internal pullup; when TRST is driven low this pin is configured as OFF, and when active low it puts all output drivers in the high-impedance state (testing and emulation only). |
| 63 | VSSO | power_in | I/O buffer ground, digital logic and buffer ground reference. |
| 64 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 65 | ADCIN15 | input | Analog input #15 to the ADC. |
| 66 | ADCIN07 | input | Analog input #7 to the ADC. |
| 67 | ADCIN06 | input | Analog input #6 to the ADC. |
| 68 | ADCIN14 | input | Analog input #14 to the ADC. |
| 69 | ADCIN05 | input | Analog input #5 to the ADC. |
| 70 | ADCIN04 | input | Analog input #4 to the ADC. |
| 71 | ADCIN13 | input | Analog input #13 to the ADC. |
| 72 | ADCIN03 | input | Analog input #3 to the ADC. |
| 73 | ADCIN12 | input | Analog input #12 to the ADC. |
| 74 | ADCIN02 | input | Analog input #2 to the ADC. |
| 75 | ADCIN11 | input | Analog input #11 to the ADC. |
| 76 | ADCIN10 | input | Analog input #10 to the ADC. |
| 77 | ADCIN01 | input | Analog input #1 to the ADC. |
| 78 | ADCIN09 | input | Analog input #9 to the ADC. |
| 79 | ADCIN00 | input | Analog input #0 to the ADC. |
| 80 | ADCIN08 | input | Analog input #8 to the ADC. |
| 81 | VREFLO | input | ADC analog low-voltage reference input. |
| 82 | VREFHI | input | ADC analog high-voltage reference input. |
| 83 | VCCA | power_in | Analog supply voltage for the ADC, 3.3 V; it is highly recommended to isolate VCCA from the digital supply for ADC accuracy and noise immunity. |
| 84 | VSSA | power_in | Analog ground reference for the ADC; it is highly recommended to isolate VSSA from digital ground. |
| 85 | BIO/IOPC1 | bidirectional | Branch control input polled by the BCND instruction (branch executed if low); if not used it should be pulled high, and it can be used as GPIO if not used as branch control input. |
| 86 | BOOT_EN/XF | bidirectional | Boot ROM enable sampled as input during reset, then driven as the XF output (driven high after reset); it must be driven with a passive circuit only. |
| 87 | XTAL1/CLKIN | input | PLL oscillator input: crystal input or clock source input to the PLL, with input frequency 4-20 MHz for crystal or external clock with PLL. |
| 88 | XTAL2 | output | Crystal output (PLL oscillator output); it goes to the high-impedance state when EMU1/OFF is active low. |
| 89 | TCLKINB/IOPF5 | bidirectional | External clock input for the EVB general-purpose timer or GPIO; the timer can also use the internal device clock. |
| 90 | VSS | power_in | Core ground, digital logic ground reference. |
| 91 | VDD | power_in | Core supply, +3.3 V digital logic supply voltage. |
| 92 | IOPF6 | bidirectional | General-purpose I/O pin with internal pullup. |
| 93 | RS | bidirectional | Device reset input and watchdog reset output (open-drain with 20 µA typical internal pullup); it is recommended to drive it with an open-drain device, and it is driven low for 128 CLKIN cycles during a watchdog reset. |
| 94 | TCK | input | JTAG test clock with internal pullup. |
| 95 | PDPINTB | input | Power drive protection interrupt input that places the EVB PWM outputs in high impedance on motor drive/power converter abnormalities; it is falling-edge sensitive. |
| 96 | TDI | input | JTAG test data input with internal pullup; clocked into the selected register on a rising edge of TCK. |
| 97 | VSSO | power_in | I/O buffer ground, digital logic and buffer ground reference. |
| 98 | VDDO | power_in | I/O buffer supply, +3.3 V digital logic and buffer supply voltage. |
| 99 | TDO | output | JTAG scan out; the contents of the selected register are shifted out on the falling edge of TCK. |
| 100 | TMS | input | JTAG test-mode select with internal pullup; clocked into the TAP controller on the rising edge of TCK. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-100(14x14) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDD, PLLVCCA, VDDO, VCCA | VDD | -0.3 | 4.6 | V | with respect to VSS | 71 | |
| VCCP range | VCCP | -0.3 | 5.5 | V | 71 | ||
| Input voltage range | VIN | -0.3 | 4.6 | V | 71 | ||
| Output voltage range, LF240xA | VO | -0.3 | 4.6 | V | LF240xA | 71 | |
| Input clamp current | IIK | -20 | 20 | mA | VIN < 0 or VIN > VCC | 71 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VCC | 71 | |
| Operating free-air temperature, A version | TA | -40 | 85 | °C | A version | 71 | |
| Junction temperature range | TJ | -40 | 150 | °C | 71 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 71 | ||
| Supply voltage VDD/VDDO | VDD | 3 | 3.3 | 3.6 | V | VDDO = VDD ± 0.3 V | 71 |
| PLL supply voltage | PLLVCCA | 3 | 3.3 | 3.6 | V | 71 | |
| ADC supply voltage | VCCA | 3 | 3.3 | 3.6 | V | VCCA should not differ from VDD by more than 0.3 V | 71 |
| Flash programming supply voltage | VCCP | 4.75 | 5 | 5.25 | V | 71 | |
| Device clock frequency (system clock) | fCLKOUT | 2 | 40 | MHz | 71 | ||
| High level input voltage | VIH | 2 | V | All inputs | 71 | ||
| High-level output source current, Group 1 | IOH | -2 | mA | Output pins Group 1; VOH = 2.4 V | 71 | ||
| High-level output source current, Group 2 | IOH | -4 | mA | Output pins Group 2; VOH = 2.4 V | 71 | ||
| High-level output source current, Group 3 | IOH | -8 | mA | Output pins Group 3; VOH = 2.4 V | 71 | ||
| Low-level output sink current, Group 1 | IOL | 2 | mA | Output pins Group 1; VOL = VOL MAX | 71 | ||
| Low-level output sink current, Group 2 | IOL | 4 | mA | Output pins Group 2; VOL = VOL MAX | 71 | ||
| Low-level output sink current, Group 3 | IOL | 8 | mA | Output pins Group 3; VOL = VOL MAX | 71 | ||
| Junction temperature | TJ | -40 | 25 | 150 | °C | 71 | |
| High-level output voltage | VOH | 2.4 | V | VDD = 3.0 V, IOH = IOHMAX | 72 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = IOLMAX | 72 | ||
| Input current (low level), with pullup | IIL | -10 | -16 | -30 | µA | With pullup; VDD = 3.3 V, VIN = 0 V | 72 |
| Input current (low level), with pulldown | IIL | -2 | 2 | µA | With pulldown; VDD = 3.3 V, VIN = 0 V | 72 | |
| Input current (high level), with pullup | IIH | -2 | 2 | µA | With pullup; VDD = 3.3 V, VIN = VDD | 72 | |
| Input current (high level), with pulldown | IIH | 10 | 16 | 30 | µA | With pulldown; VDD = 3.3 V, VIN = VDD | 72 |
| Leakage current, high-impedance state (off-state) | IOZ | -2 | 2 | µA | VO = VDD or 0 V | 72 | |
| Input capacitance | Ci | 2 | pF | 72 | |||
| Output capacitance | Co | 3 | pF | 72 | |||
| Operational current, LF2406A | IDD | 95 | 120 | mA | 40-MHz CLKOUT; test code in B0 RAM; all I/O pins floating | 72 | |
| ADC module current, LF2406A | ICCA | 10 | 22 | mA | 72 | ||
| Operational current, LPM0, LF2406A | IDD | 70 | 80 | mA | LPM0; clock to all peripherals is enabled | 73 | |
| ADC module current, LPM0, LF2406A | ICCA | 10 | 22 | mA | LPM0; clock to all peripherals is enabled; no I/O pins are switching | 73 | |
| Operational current, LPM1, LF2406A | IDD | 35 | 45 | mA | LPM1; clock to all peripherals is disabled | 73 | |
| ADC module current, LPM1, LF2406A | ICCA | 0 | 0 | mA | LPM1; clock to all peripherals is disabled; no I/O pins are switching | 73 | |
| Operational current, LPM2, LF2406A | IDD | 200 | 400 | µA | LPM2; clock to all peripherals is disabled; Flash is powered down | 73 | |
| ADC module current, LPM2, LF2406A | ICCA | 0 | 0 | mA | LPM2; Flash is powered down; input clock is disabled | 73 | |
| ADC analog input reference current | IADREFHI | 0.75 | 1.5 | mA | 108 | ||
| Analog input leakage | IADCIN | 1 | µA | 108 | |||
| ADC operating frequency | 4 | 30 | MHz | 107 | |||
| Differential nonlinearity error | EDNL | 2 | LSB | CLKOUT 30 MHz; VREFHI = VCCA, VREFLO = VSSA | 108 | ||
| Integral nonlinearity error | EINL | 2 | LSB | CLKOUT 30 MHz; VREFHI = VCCA, VREFLO = VSSA | 108 | ||
| Cycle time, ADC prescaled clock | tc(AD) | 33.3 | ns | 109 | |||
| Input clock frequency, resonator | fx | 4 | 13 | MHz | Resonator | 80 | |
| Input clock frequency, crystal | fx | 4 | 20 | MHz | Crystal | 80 | |
| Cycle time, CLKOUT ×4 mode | tc(CO) | 25 | ns | PLL ×4 mode | 80 | ||
| Fall time, CLKOUT | tf(CO) | 4 | ns | 80 | |||
| Rise time, CLKOUT | tr(CO) | 4 | ns | 80 | |||
| Cycle time, XTAL1/CLKIN | tc(Cl) | 250 | ns | 80 | |||
| Fall time, XTAL1/CLKIN | tf(Cl) | 5 | ns | 80 | |||
| Rise time, XTAL1/CLKIN | tr(Cl) | 5 | ns | 80 | |||
| Pulse duration, XTAL1/CLKIN low as % of tc(Cl) | tw(CIL) | 40 | 60 | % | 80 | ||
| Pulse duration, XTAL1/CLKIN high as % of tc(Cl) | tw(CIH) | 40 | 60 | % | 80 | ||
| Junction-to-ambient thermal resistance, PZ package | ΘJA | 42 | °C/W | PZ package, typical | 126 | ||
| Junction-to-case thermal resistance, PZ package | ΘJC | 8 | °C/W | PZ package, typical | 126 | ||
| Junction-to-top of package thermal characterization, PZ package | Ψjt | 0.5 | °C/W | PZ package, typical | 126 |
CAD (KiCad official)
- Symbol:
TMS320LF2406APZAR - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
tms320lf2406apzar-etched.step/tms320lf2406apzar-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tms320lf2406apzar.step/tms320lf2406apzar.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (141 pp, sha256
f19019cb4a75676b, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).