Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS70202PWP

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HTSSOP-20

TPS70202PWP from Texas Instruments, in a HTSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No internal connection; leave unconnected.
2 VIN1 power_in Input voltage of regulator 1; recommended range is 2.7 V to 6 V and absolute maximum is -0.3 V to +7 V.
3 VIN1 power_in Input voltage of regulator 1; recommended range is 2.7 V to 6 V and absolute maximum is -0.3 V to +7 V.
4 MR input Manual reset input, active low, pulled up internally by a 6 µA source to VIN1; logic-low threshold 0.7 V and logic-high threshold 2 V.
5 EN1 input Active low enable for VOUT1; logic-high threshold 2 V, logic-low threshold 0.7 V, input current ±1 µA.
6 EN2 input Active low enable for VOUT2; logic-high threshold 2 V, logic-low threshold 0.7 V, input current ±1 µA.
7 RESET output Open drain, active low SVS (power-on reset) output that asserts on undervoltage and needs an external pull-up resistor; it releases after a 120 ms delay (80 to 160 ms).
8 GND power_in Ground.
9 VIN2 power_in Input voltage of regulator 2; recommended range is 2.7 V to 6 V and absolute maximum is -0.3 V to +7 V.
10 VIN2 power_in Input voltage of regulator 2; recommended range is 2.7 V to 6 V and absolute maximum is -0.3 V to +7 V.
11 NC unconnected No internal connection; leave unconnected.
12 VOUT2 power_out Output voltage of regulator 2, rated up to 250 mA; peak output current is 375 mA for a 2 ms pulse.
13 VOUT2 power_out Output voltage of regulator 2, rated up to 250 mA; peak output current is 375 mA for a 2 ms pulse.
14 VSENSE2/FB2 input Regulator 2 output voltage sense for fixed-output versions or feedback input for the adjustable version (1.22 V to 5.5 V); keep the connection to the divider or VOUT2 as short as possible.
15 PG2 output Open drain power-good output, low when VOUT2 is below 95% of its nominal regulated voltage; requires a pull-up resistor.
16 PG1 output Open drain power-good output, low when VOUT1 is below 95% of its nominal regulated voltage; requires a pull-up resistor.
17 VSENSE1/FB1 input Regulator 1 output voltage sense for fixed-output versions or feedback input for the adjustable version (1.22 V to 5.5 V); keep the connection to the divider or VOUT1 as short as possible.
18 VOUT1 power_out Output voltage of regulator 1, rated up to 500 mA; peak output current is 750 mA for a 2 ms pulse.
19 VOUT1 power_out Output voltage of regulator 1, rated up to 500 mA; peak output current is 750 mA for a 2 ms pulse.
20 NC unconnected No internal connection; leave unconnected.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20
Category Power Management (PMIC)
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output voltage range (VOUT1, VSENSE1) VOUT1, VSENSE1 5.5 V 3
Output voltage range (VOUT2, VSENSE2) VOUT2, VSENSE2 5.5 V 3
Maximum RESET, PG1, PG2 voltage 7 V 3
Input voltage range VIN1, VIN2 -0.3 7 V All voltages tied to network ground 3
Voltage range at EN1, EN2 EN1, EN2 -0.3 7 V 3
Operating virtual junction temperature range TJ -40 150 °C 3
Storage temperature range Tstg -65 150 °C 3
ESD rating, HBM 2 kV HBM 3
Input voltage (regulator 1 and 2) VI 2.7 6 V 4
Output current, regulator 1 IO 0 500 mA 4
Output current, regulator 2 IO 0 250 mA 4
Output voltage range (adjustable option) 1.22 5.5 V 4
Operating virtual junction temperature TJ -40 125 °C 4
Reference voltage 1.196 1.244 V 2.7V < VIN < 6V, FB connected to VO 5
Output voltage, 1.2V output option 1.176 1.224 V 2.7V < VIN < 6V, 1.2V output 5
Quiescent current (GND current) for regulator 1 and regulator 2 230 μA EN1 = EN2 = 0V; see note 2 5
Output voltage line regulation (ΔVO/VO) for regulator 1 and regulator 2 ΔVO/VO 0.1 %/V VO + 1V < VIN ≤ 6V 5
Output current limit, regulator 1 1.6 1.9 A VOUT = 0V 5
Output current limit, regulator 2 0.75 1 A VOUT = 0V 5
UVLO threshold 2.4 2.65 V 5
Minimum input voltage for valid RESET 1 1.3 V IRESET = 300μA, V(RESET) ≤ 0.8V 5
RESET pulse duration t(RESET) 80 120 160 ms 5
RESET output low voltage 0.15 0.4 V VIN = 3.5V, I(RESET) = 1mA 5
Minimum input voltage for valid PGx 1 1.3 V I(PGx) = 300μA, V(PGx) ≤ 0.8V 6
PGx trip threshold voltage 92 95 98 %VOUT VO decreasing 6
PGx output low voltage 0.15 0.4 V VIN = 2.7V, I(PGx) = 1mA 6
High-level ENx input voltage 2 V 6
Low-level ENx input voltage 0.7 V 6
Input current (ENx) -1 1 μA 6
MR high-level input voltage 2 V 6
MR low-level input voltage 0.7 V 6
Dropout voltage, VOUT1 275 mV IO = 500mA, VIN1 = 3.2V 6
Dissipation rating, PWP, 0 CFM PD 3.067 W TA ≤ +25°C 4
Dissipation rating, PWP, 0 CFM PD 1.687 W TA = +70°C 4
Dissipation rating, PWP, 0 CFM PD 1.227 W TA = +85°C 4
Dissipation rating, PWP, 250 CFM PD 4.115 W TA ≤ +25°C 4
Dissipation rating, PWP, 250 CFM PD 2.265 W TA = +70°C 4
Dissipation rating, PWP, 250 CFM PD 1.646 W TA = +85°C 4
Junction-to-ambient thermal resistance (RθJA) RθJA 32.6 °C/W 20-terminal PWP, no airflow 28

CAD (KiCad official)

  • Symbol: TPS70202PWP
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tps70202pwp-etched.step / tps70202pwp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps70202pwp.step / tps70202pwp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (39 pp, sha256 442e41a4a4622bc2, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF