3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMP4420HGJ-P
Monolithic Power Systems · DC-DC Converters · TSOT-23-8
MP4420HGJ-P from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Power good is an open-drain output that goes high when the output voltage exceeds 90% of its nominal value and must be pulled up through a resistor (e.g., 100kΩ) to VCC or another voltage source. |
| 2 | IN | power_in | Supply input that operates from a 4V to 36V input rail and requires a C1 input capacitor for decoupling, connected with a wide PCB trace. |
| 3 | SW | output | Switch output node that must be connected with a wide PCB trace; the absolute maximum rating for VSW is -0.3V to 41V. |
| 4 | GND | power_in | System ground and reference for the regulated output voltage, to be connected to the ground plane with copper traces and vias per the layout requirements. |
| 5 | BST | power_out | Bootstrap pin that forms a floating high-side driver supply with a capacitor to SW, where a 20Ω series resistor is strongly recommended; the absolute maximum rating is VBS = VSW + 6V. |
| 6 | EN/SYNC | input | Enable and synchronization input where high enables the regulator and low disables it, an external 200kHz to 2.2MHz clock can synchronize the switching frequency, and the pin is clamped by a 6.5V Zener so that direct connection to a source requires voltage ≤6V. |
| 7 | VCC | power_out | Bias supply output of the internal 5V regulator (4.6V to 5.2V at ICC = 0mA) that must be decoupled with a 0.1µF to 0.22µF capacitor not exceeding 0.22µF. |
| 8 | FB | input | Feedback input connected to the tap of the output resistor divider, which regulates to the 0.8V reference (VFB 780mV to 804mV) and triggers frequency fold-back when the FB voltage falls below 660mV. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current (Quiescent) | IQ | 0.5 | 0.7 | mA | VEN = 2V, VFB = 1V | 4 | |
| HS Switch-ON Resistance | RON_HS | 90 | 105 | mΩ | VBST-SW=5V | 4 | |
| LS Switch-ON Resistance | RON_LS | 55 | 75 | mΩ | VCC =5V | 4 | |
| Current Limit | ILIMIT | 3.2 | 4.2 | 5.3 | A | Under 40% Duty Cycle | 4 |
| Oscillator Frequency | fSW | 320 | 410 | 500 | kHz | VFB=750mV | 4 |
| Fold-Back Frequency | fFB | 70 | 100 | 130 | kHz | VFB<400mV | 4 |
| Maximum Duty Cycle | DMAX | 92 | 95 | % | VFB=750mV, 410kHz | 4 | |
| Sync Frequency Range | fSYNC | 0.2 | 2.4 | MHz | 4 | ||
| Feedback Voltage | VFB | 780 | 792 | 804 | mV | 4 | |
| Feedback Current | IFB | 10 | 100 | nA | VFB=820mV | 4 | |
| EN Rising Threshold | VEN RISING | 1.15 | 1.4 | 1.65 | V | 4 | |
| EN Falling Threshold | VEN FALLING | 1.05 | 1.25 | 1.45 | V | 4 | |
| EN Input Current | IEN | 4 | 6 | μA | VEN=2V | 4 | |
| EN Input Current | IEN | 0 | 0.2 | μA | VEN=0 | 4 | |
| VIN Under-Voltage Lockout Threshold-Rising | INUVRISING | 3.3 | 3.5 | 3.7 | V | 4 | |
| VIN Under-Voltage Lockout Threshold-Falling | INUVFALLING | 3.1 | 3.3 | 3.5 | V | 4 | |
| VCC Regulator | VCC | 4.6 | 4.9 | 5.2 | V | ICC=0mA | 4 |
| VCC Load Regulation | 1.5 | 4 | % | ICC=5mA | 4 | ||
| Soft-Start Period | tSS | 0.55 | 1.45 | 2.45 | ms | VOUT from 10% to 90% | 4 |
| Thermal Shutdown | 150 | 170 | °C | 4 | |||
| PG Rising Threshold | PGVth RISING | 86.5 | 90 | 93.5 | % | as percentage of VFB | 4 |
| PG Falling Threshold | PGVth FALLING | 80.5 | 84 | 87.5 | % | as percentage of VFB | 4 |
| PG Rising Delay | PGTd_RISING | 40 | 90 | 160 | μs | 5 | |
| PG Falling Delay | PGTd_FALLING | 30 | 55 | 95 | μs | 5 | |
| PG Sink Current Capability | VPG Sink | 0.1 | 0.3 | V | Sink 4mA | 5 | |
| PG Leakage Current | ILKG_PG | 10 | 100 | nA | 5 | ||
| Input Voltage (absolute maximum) | VIN | -0.3 | 40 | V | 3 | ||
| Switch Voltage (absolute maximum) | VSW | -0.3 | 41 | V | 3 | ||
| All Other Pins (absolute maximum) | -0.3 | 6 | V | 3 | |||
| Continuous Power Dissipation | 1.25 | W | TA = +25°C, TSOT23-8 | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| Lead Temperature | 260 | °C | 3 | ||||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Continuous Supply Voltage | VIN | 4 | 36 | V | 3 | ||
| Output Voltage | VOUT | 0.8 | V | Upper limit printed as 0.9xVIN | 3 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 3 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 100 | °C/W | Measured on JESD51-7, 4-layer PCB | 3 | ||
| Junction-to-Case Thermal Resistance | θJC | 55 | °C/W | Measured on JESD51-7, 4-layer PCB | 3 | ||
| Supply Current (Shutdown) | ISHDN | 8 | μA | VEN = 0V | 4 | ||
| Switch Leakage | ILKG SW | 1 | μA | VEN = 0V, VSW =12V | 4 | ||
| Minimum ON Time | tON MIN | 70 | ns | 4 | |||
| EN Threshold Hysteresis | VEN_HYS | 150 | mV | 4 | |||
| VIN Under-Voltage Lockout Threshold-Hysteresis | INUVHYS | 200 | mV | 4 | |||
| Thermal Hysteresis | 30 | °C | 4 | ||||
| PG Threshold Hysteresis | PGVth_HYS | 6 | % | as percentage of VFB | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 4 GND System Ground. This pin is the reference ground of the regulated output voltage, and PCB layout requires special care. For best results, connect to GND with copper traces and vias. | 12 |
CAD (KiCad official)
- Symbol:
MP4420HGJ-P - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mp4420hgj-p-etched.step/mp4420hgj-p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4420hgj-p.step/mp4420hgj-p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (20 pp, sha256
c68628245baef462, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).