Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NCS21914DR2G

onsemi · Precision Op Amps · SOIC-14

NCS21914DR2G from onsemi, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT1 output Amplifier 1 output. Rail-to-rail output stage, swings within ~10 mV of the supply rails; short-circuit current typ. 16 mA sourcing / 18 mA sinking; drives up to 1 nF capacitive load.
2 IN-1 input Amplifier 1 inverting input. High-impedance CMOS input; input bias current typ. ±100 pA; input diode-clamped to supply rails through 1.65 kΩ (limit input current to ±10 mA).
3 IN+1 input Amplifier 1 non-inverting input. Common-mode range VSS to VDD-1.5 V; CMRR typ. 150 dB at VS = 36 V; ESD/latch-up protected inputs.
4 VDD power_in Positive supply pin, shared by all four amplifiers. Operating range 4 V to 36 V (VDD-VSS ≤ 40 V absolute max). Quiescent current typ. 475 µA / max 570 µA per channel. Bypass with a local 0.1 µF ceramic close to the pin.
5 IN+2 input Amplifier 2 non-inverting input. Common-mode range VSS to VDD-1.5 V; input impedance is very high (CMOS gate).
6 IN-2 input Amplifier 2 inverting input. High-impedance input; differential input voltage limited to ±17 V by internal clamp diodes with 1.65 kΩ series protection.
7 OUT2 output Amplifier 2 output. Rail-to-rail; VOH/VOL typ. 100 mV from rail with 10 kΩ load; slew rate typ. 1.6 V/µs.
8 OUT3 output Amplifier 3 output. Rail-to-rail output; short-circuit protected; drives up to 1 nF cap load.
9 IN-3 input Amplifier 3 inverting input. High-impedance CMOS input; internal input protection diodes to VDD/VSS with 1.65 kΩ series (limit external input current to ±10 mA).
10 IN+3 input Amplifier 3 non-inverting input. Common-mode range VSS to VDD-1.5 V.
11 VSS power_in Negative supply / ground pin, shared by all four amplifiers. Total supply (VDD-VSS) 4 V to 36 V operating, 40 V absolute max. In single-supply designs tie to GND.
12 IN+4 input Amplifier 4 non-inverting input. Common-mode range VSS to VDD-1.5 V; CMOS high-impedance input.
13 IN-4 input Amplifier 4 inverting input. High-impedance input; internal ESD/latch-up protection.
14 OUT4 output Amplifier 4 output. Rail-to-rail; open-loop gain typ. 150 dB; output impedance behavior per Figure 23.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-14
Category Amplifiers/Comparators
Pins 14

Ordering variants

Same part, different packaging or reel option.

  • NCS21914DR2G
  • NCS21914DR2GNCV21914DR2G
  • NCS21914DTBR2G
  • NCS21914DR2GNCV21914DTBR2G

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Offset Voltage VOS -25 1 25 V 4
Offset Voltage Drift vs Temp VOS/T -0.085 0.02 0.085 V/°C 4
Input Bias Current IIB -500 100 500 pA 4
Input Bias Current (boldface, over temperature) IIB -3500 3500 pA Boldface: TA = –40°C to 125°C 4
Input Offset Current IOS -500 200 500 pA 4
Input Offset Current (boldface, over temperature) IOS -3500 3500 pA Boldface: TA = –40°C to 125°C 4
Common Mode Rejection Ratio CMRR 140 150 dB VSS ≤ VCM ≤ VDD−1.5 V, VS = 36 V 4
Common Mode Rejection Ratio (boldface, over temperature) CMRR 130 dB Boldface: TA = –40°C to 125°C, VS = 36 V 4
Common Mode Rejection Ratio CMRR 130 150 dB VSS ≤ VCM ≤ VDD−1.5 V, VS = 12 V (Note 8) 4
Common Mode Rejection Ratio (boldface, over temperature) CMRR 120 dB Boldface: TA = –40°C to 125°C, VS = 12 V (Note 8) 4
Common Mode Rejection Ratio CMRR 130 140 dB VSS ≤ VCM ≤ VDD−1.5 V, VS = 8 V (Note 8) 4
Common Mode Rejection Ratio CMRR 120 130 dB VSS ≤ VCM ≤ VDD−1.5 V, VS = 4 V 4
Common Mode Rejection Ratio (boldface, over temperature) CMRR 110 dB Boldface: TA = –40°C to 125°C, VS = 4 V 4
Open Loop Voltage Gain AVOL 130 150 dB VSS + 0.5 V < VO < VDD – 0.5 V 4
Open Loop Voltage Gain (boldface, over temperature) AVOL 125 135 dB Boldface: TA = –40°C to 125°C, VSS + 0.5 V < VO < VDD – 0.5 V 4
Output Voltage High, Referenced to Rail VOH 5 10 mV No Load 4
Output Voltage High, Referenced to Rail VOH 100 210 mV RL = 10 k 4
Output Voltage High, Referenced to Rail (boldface, over temperature) VOH 140 250 mV Boldface: TA = –40°C to 125°C, RL = 10 k 4
Output Voltage Low, Referenced to Rail VOL 5 10 mV No Load 4
Output Voltage Low, Referenced to Rail VOL 100 210 mV RL = 10 k 4
Output Voltage Low, Referenced to Rail (boldface, over temperature) VOL 140 250 mV Boldface: TA = –40°C to 125°C, RL = 10 k 4
Power Supply Rejection Ratio PSRR 0.02 0.3 V/V VS = 4 V to 36 V 5
Power Supply Rejection Ratio PSRR 130 154 dB VS = 4 V to 36 V 5
Quiescent Current IQ 475 570 A Per channel 5
Quiescent Current (boldface, over temperature) IQ 570 A Boldface: TA = –40°C to 125°C, per channel 5
Supply Voltage (VDD − VSS) VS 40 V 3
Differential Input Voltage VID -17 17 V Note 2: inputs diode connected with 1.65 kΩ total input protection 3
Input Current II -10 10 mA Notes 1 and 2 3
Operating Temperature TA -40 125 °C 3
Storage Temperature TSTG -65 150 °C 3
Junction Temperature TJ 150 °C 3
ESD Human Body Model (HBM) ESD HBM 3000 V JS-001-2017 (AEC-Q100-002) 3
ESD Charged Device Model (CDM) ESD CDM 2000 V JS-002-2014 (AEC-Q100-011) 3
Latch-up Current ILU 100 mA JESD78E (AEC-Q100-004) 3
Supply Voltage (VDD − VSS) VS 4 36 V 3
Specified Operating Temperature Range TA -40 125 °C 3
Differential Voltage VDIFF -17 17 V Note 7 3
Thermal Resistance, Junction to Ambient (SOIC-14) JA 59 °C/W As mounted on 80x80x1.5 mm FR4 PCB, 2S2P, 2 oz copper, 200 mm² heat spreader, JESD51-7 3

CAD (KiCad official)

  • Symbol: NCS21914DR2G
  • Footprint: Package_SO:SOIC-14_3.9x8.7mm_P1.27mm
  • 3D model: SOIC-14 (KiCad packages3D, STEP)
  • 3D model files: ncs21914dr2g-etched.step / ncs21914dr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncs21914dr2g.step / ncs21914dr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (22 pp, sha256 f5d8387cd1d9293b, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF